Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

5 files changed, 771 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml
new file mode 100644
index 000000000..382ddab60
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,da8xx-ddrctl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments da8xx DDR2/mDDR memory controller
+
+maintainers:
+  - Bartosz Golaszewski <bgolaszewski@baylibre.com>
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  Documentation:
+    OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
+
+properties:
+  compatible:
+    const: ti,da850-ddr-controller
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@b0000000 {
+        compatible = "ti,da850-ddr-controller";
+        reg = <0xb0000000 0xe8>;
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml
new file mode 100644
index 000000000..383d19e0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml
@@ -0,0 +1,252 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments GPMC Bus Child Nodes
+
+maintainers:
+  - Tony Lindgren <tony@atomide.com>
+  - Roger Quadros <rogerq@kernel.org>
+
+description:
+  This binding is meant for the child nodes of the GPMC node. The node
+  represents any device connected to the GPMC bus. It may be a Flash chip,
+  RAM chip or Ethernet controller, etc. These properties are meant for
+  configuring the GPMC settings/timings and will accompany the bindings
+  supported by the respective device.
+
+properties:
+  reg: true
+
+# GPMC Timing properties for child nodes. All are optional and default to 0.
+  gpmc,sync-clk-ps:
+    description: Minimum clock period for synchronous mode
+    default: 0
+
+# Chip-select signal timings corresponding to GPMC_CONFIG2:
+  gpmc,cs-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,cs-rd-off-ns:
+    description: Read deassertion time
+    default: 0
+
+  gpmc,cs-wr-off-ns:
+    description: Write deassertion time
+    default: 0
+
+# ADV signal timings corresponding to GPMC_CONFIG3:
+  gpmc,adv-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,adv-rd-off-ns:
+    description: Read deassertion time
+    default: 0
+
+  gpmc,adv-wr-off-ns:
+    description: Write deassertion time
+    default: 0
+
+  gpmc,adv-aad-mux-on-ns:
+    description: Assertion time for AAD
+    default: 0
+
+  gpmc,adv-aad-mux-rd-off-ns:
+    description: Read deassertion time for AAD
+    default: 0
+
+  gpmc,adv-aad-mux-wr-off-ns:
+    description: Write deassertion time for AAD
+    default: 0
+
+# WE signals timings corresponding to GPMC_CONFIG4:
+  gpmc,we-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,we-off-ns:
+    description: Deassertion time
+    default: 0
+
+# OE signals timings corresponding to GPMC_CONFIG4:
+  gpmc,oe-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,oe-off-ns:
+    description: Deassertion time
+    default: 0
+
+  gpmc,oe-aad-mux-on-ns:
+    description: Assertion time for AAD
+    default: 0
+
+  gpmc,oe-aad-mux-off-ns:
+    description: Deassertion time for AAD
+    default: 0
+
+# Access time and cycle time timings (in nanoseconds) corresponding to
+# GPMC_CONFIG5:
+  gpmc,page-burst-access-ns:
+    description: Multiple access word delay
+    default: 0
+
+  gpmc,access-ns:
+    description: Start-cycle to first data valid delay
+    default: 0
+
+  gpmc,rd-cycle-ns:
+    description: Total read cycle time
+    default: 0
+
+  gpmc,wr-cycle-ns:
+    description: Total write cycle time
+    default: 0
+
+  gpmc,bus-turnaround-ns:
+    description: Turn-around time between successive accesses
+    default: 0
+
+  gpmc,cycle2cycle-delay-ns:
+    description: Delay between chip-select pulses
+    default: 0
+
+  gpmc,clk-activation-ns:
+    description: GPMC clock activation time
+    default: 0
+
+  gpmc,wait-monitoring-ns:
+    description: Start of wait monitoring with regard to valid data
+    default: 0
+
+# Boolean timing parameters. If property is present, parameter is enabled
+# otherwise disabled.
+  gpmc,adv-extra-delay:
+    description: ADV signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,cs-extra-delay:
+    description: CS signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,cycle2cycle-diffcsen:
+    description: |
+      Add "cycle2cycle-delay" between successive accesses
+      to a different CS
+    type: boolean
+
+  gpmc,cycle2cycle-samecsen:
+    description: |
+      Add "cycle2cycle-delay" between successive accesses
+      to the same CS
+    type: boolean
+
+  gpmc,oe-extra-delay:
+    description: OE signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,we-extra-delay:
+    description: WE signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,time-para-granularity:
+    description: Multiply all access times by 2
+    type: boolean
+
+# The following two properties are applicable only to OMAP3+ and AM335x:
+  gpmc,wr-access-ns:
+    description: |
+      In synchronous write mode, for single or
+      burst accesses, defines the number of
+      GPMC_FCLK cycles from start access time
+      to the GPMC_CLK rising edge used by the
+      memory device for the first data capture.
+    default: 0
+
+  gpmc,wr-data-mux-bus-ns:
+    description: |
+      In address-data multiplex mode, specifies
+      the time when the first data is driven on
+      the address-data bus.
+    default: 0
+
+# GPMC chip-select settings properties for child nodes. All are optional.
+  gpmc,burst-length:
+    description: Page/burst length.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 4, 8, 16]
+    default: 0
+
+  gpmc,burst-wrap:
+    description: Enables wrap bursting
+    type: boolean
+
+  gpmc,burst-read:
+    description: Enables read page/burst mode
+    type: boolean
+
+  gpmc,burst-write:
+    description: Enables write page/burst mode
+    type: boolean
+
+  gpmc,device-width:
+    description: |
+      Total width of device(s) connected to a GPMC
+      chip-select in bytes. The GPMC supports 8-bit
+      and 16-bit devices and so this property must be
+      1 or 2.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2]
+    default: 1
+
+  gpmc,mux-add-data:
+    description: |
+      Address and data multiplexing configuration.
+      Valid values are
+      0 for Non multiplexed mode
+      1 for address-address-data multiplexing mode and
+      2 for address-data multiplexing mode.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2]
+
+  gpmc,sync-read:
+    description: |
+      Enables synchronous read. Defaults to asynchronous
+      is this is not set.
+    type: boolean
+
+  gpmc,sync-write:
+    description: |
+      Enables synchronous writes. Defaults to asynchronous
+      is this is not set.
+    type: boolean
+
+  gpmc,wait-pin:
+    description: |
+      Wait-pin used by client. Must be less than "gpmc,num-waitpins".
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  ti,wait-pin-polarity:
+    description: |
+      Set the desired polarity for the selected wait pin.
+      0 for active low, 1 for active high.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  gpmc,wait-on-read:
+    description: Enables wait monitoring on reads.
+    type: boolean
+
+  gpmc,wait-on-write:
+    description: Enables wait monitoring on writes.
+    type: boolean
+
+required:
+  - reg
+
+# the GPMC child will have its own native properties
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
new file mode 100644
index 000000000..4f30173ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
@@ -0,0 +1,190 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments GPMC Memory Controller
+
+maintainers:
+  - Tony Lindgren <tony@atomide.com>
+  - Roger Quadros <rogerq@kernel.org>
+
+description:
+  The GPMC is a unified memory controller dedicated for interfacing
+  with external memory devices like
+  - Asynchronous SRAM-like memories and ASICs
+  - Asynchronous, synchronous, and page mode burst NOR flash
+  - NAND flash
+  - Pseudo-SRAM devices
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - ti,am3352-gpmc
+          - ti,am64-gpmc
+          - ti,omap2420-gpmc
+          - ti,omap2430-gpmc
+          - ti,omap3430-gpmc
+          - ti,omap4430-gpmc
+
+  reg:
+    minItems: 1
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: cfg
+      - const: data
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: |
+      Functional clock. Used for bus timing calculations and
+      GPMC configuration.
+
+  clock-names:
+    items:
+      - const: fck
+
+  power-domains:
+    maxItems: 1
+
+  dmas:
+    items:
+      - description: DMA channel for GPMC NAND prefetch
+
+  dma-names:
+    items:
+      - const: rxtx
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  gpmc,num-cs:
+    description: maximum number of supported chip-select lines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  gpmc,num-waitpins:
+    description: maximum number of supported wait pins.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  ranges:
+    minItems: 1
+    description: |
+      Must be set up to reflect the memory layout with four
+      integer values for each chip-select line in use,
+      <cs-number> 0 <physical address of mapping> <size>
+    items:
+      - description: NAND bank 0
+      - description: NOR/SRAM bank 0
+      - description: NOR/SRAM bank 1
+
+  '#interrupt-cells':
+    const: 2
+
+  interrupt-controller:
+    description: |
+      The GPMC driver implements and interrupt controller for
+      the NAND events "fifoevent" and "termcount" plus the
+      rising/falling edges on the GPMC_WAIT pins.
+      The interrupt number mapping is as follows
+      0 - NAND_fifoevent
+      1 - NAND_termcount
+      2 - GPMC_WAIT0 pin edge
+      3 - GPMC_WAIT1 pin edge, and so on.
+
+  '#gpio-cells':
+    const: 2
+
+  gpio-controller:
+    description: |
+      The GPMC driver implements a GPIO controller for the
+      GPMC WAIT pins that can be used as general purpose inputs.
+      0 maps to GPMC_WAIT0 pin.
+
+  ti,hwmods:
+    description:
+      Name of the HWMOD associated with GPMC. This is for legacy
+      omap2/3 platforms only.
+    $ref: /schemas/types.yaml#/definitions/string
+    deprecated: true
+
+  ti,no-idle-on-init:
+    description:
+      Prevent idling the module at init. This is for legacy omap2/3
+      platforms only.
+    type: boolean
+    deprecated: true
+
+patternProperties:
+  "@[0-7],[a-f0-9]+$":
+    type: object
+    description: |
+      The child device node represents the device connected to the GPMC
+      bus. The device can be a NAND chip, SRAM device, NOR device
+      or an ASIC.
+    $ref: "ti,gpmc-child.yaml"
+
+
+required:
+  - compatible
+  - reg
+  - gpmc,num-cs
+  - gpmc,num-waitpins
+  - "#address-cells"
+  - "#size-cells"
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,am64-gpmc
+    then:
+      required:
+        - reg-names
+        - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    gpmc: memory-controller@50000000 {
+      compatible = "ti,am3352-gpmc";
+      reg = <0x50000000 0x2000>;
+      interrupts = <100>;
+      clocks = <&l3s_clkctrl>;
+      clock-names = "fck";
+      dmas = <&edma 52 0>;
+      dma-names = "rxtx";
+      gpmc,num-cs = <8>;
+      gpmc,num-waitpins = <2>;
+      #address-cells = <2>;
+      #size-cells = <1>;
+      ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+      interrupt-controller;
+      #interrupt-cells = <2>;
+      gpio-controller;
+      #gpio-cells = <2>;
+
+      nand@0,0 {
+        compatible = "ti,omap2-nand";
+        reg = <0 0 4>;
+        interrupt-parent = <&gpmc>;
+        interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+                     <1 IRQ_TYPE_NONE>; /* termcount */
+        ti,nand-xfer-type = "prefetch-dma";
+        ti,nand-ecc-opt = "bch16";
+        ti,elm-id = <&elm>;
+        rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
+      };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
new file mode 100644
index 000000000..190437a0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
@@ -0,0 +1,210 @@
+* Device tree bindings for Texas instruments AEMIF controller
+
+The Async External Memory Interface (EMIF16/AEMIF) controller is intended to
+provide a glue-less interface to a variety of asynchronous memory devices like
+ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
+can be accessed at any given time via four chip selects with 64M byte access
+per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM
+and Mobile SDR are not supported.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible:		"ti,davinci-aemif"
+			"ti,keystone-aemif"
+			"ti,da850-aemif"
+
+- reg:			contains offset/length value for AEMIF control registers
+			space.
+
+- #address-cells:	Must be 2. The partition number has to be encoded in the
+			first address cell and it may accept values 0..N-1
+			(N - total number of partitions). It's recommended to
+			assign N-1 number for the control partition. The second
+			cell is the offset into the partition.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Contains memory regions. There are two types of
+			ranges/partitions:
+			- CS-specific partition/range. If continuous, must be
+			set up to reflect the memory layout for 4 chipselects,
+			if not then additional range/partition can be added and
+			child device can select the proper one.
+			- control partition which is common for all CS
+			interfaces.
+
+- clocks:		the clock feeding the controller clock. Required only
+			if clock tree data present in device tree.
+			See clock-bindings.txt
+
+- clock-names:		clock name. It has to be "aemif". Required only if clock
+			tree data present in device tree, in another case don't
+			use it.
+			See clock-bindings.txt
+
+- clock-ranges:		Empty property indicating that child nodes can inherit
+			named clocks. Required only if clock tree data present
+			in device tree.
+			See clock-bindings.txt
+
+
+Child chip-select (cs) nodes contain the memory devices nodes connected to
+such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt).
+There might be board specific devices like FPGAs.
+
+Required child cs node properties:
+
+- #address-cells:	Must be 2.
+
+- #size-cells:		Must be 1.
+
+- ranges:		Empty property indicating that child nodes can inherit
+			memory layout.
+
+- clock-ranges:		Empty property indicating that child nodes can inherit
+			named clocks. Required only if clock tree data present
+			in device tree.
+
+- ti,cs-chipselect:	number of chipselect. Indicates on the aemif driver
+			which chipselect is used for accessing the memory. For
+			compatibles "ti,davinci-aemif" and "ti,keystone-aemif"
+			it can be in range [0-3]. For compatible
+			"ti,da850-aemif" range is [2-5].
+
+Optional child cs node properties:
+
+- ti,cs-bus-width:		width of the asynchronous device's data bus
+				8 or 16 if not preset 8
+
+- ti,cs-select-strobe-mode:	enable/disable select strobe mode
+				In select strobe mode chip select behaves as
+				the strobe and is active only during the strobe
+				period. If present then enable.
+
+- ti,cs-extended-wait-mode:	enable/disable extended wait mode
+				if set, the controller monitors the EMIFWAIT pin
+				mapped to that chip select to determine if the
+				device wants to extend the strobe period. If
+				present then enable.
+
+- ti,cs-min-turnaround-ns:	minimum turn around time, ns
+				Time between the end of one asynchronous memory
+				access and the start of another asynchronous
+				memory access. This delay is not incurred
+				between a read followed by read or a write
+				followed by a write to same chip select.
+
+- ti,cs-read-setup-ns:		read setup width, ns
+				Time between the beginning of a memory cycle
+				and the activation of read strobe.
+				Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-strobe-ns:		read strobe width, ns
+				Time between the activation and deactivation of
+				the read strobe.
+				Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-hold-ns:		read hold width, ns
+				Time between the deactivation of the read
+				strobe and the end of the cycle (which may be
+				either an address change or the deactivation of
+				the chip select signal.
+				Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-setup-ns:		write setup width, ns
+				Time between the beginning of a memory cycle
+				and the activation of write strobe.
+				Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-strobe-ns:	write strobe width, ns
+				Time between the activation and deactivation of
+				the write strobe.
+				Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-hold-ns:		write hold width, ns
+				Time between the deactivation of the write
+				strobe and the end of the cycle (which may be
+				either an address change or the deactivation of
+				the chip select signal.
+				Minimum value is 1 (0 treated as 1).
+
+If any of the above parameters are absent, current parameter value will be taken
+from the corresponding HW reg.
+
+Example for aemif, davinci nand and nor flash chip select shown below.
+
+memory-controller@21000a00 {
+	compatible = "ti,davinci-aemif";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	clocks = <&clkaemif 0>;
+	clock-names = "aemif";
+	clock-ranges;
+	reg = <0x21000A00 0x00000100>;
+	ranges = <0 0 0x70000000 0x10000000
+		  1 0 0x21000A00 0x00000100>;
+		  /*
+		   * Partition0: CS-specific memory range which is
+		   * implemented as continuous physical memory region
+		   * Partition1: control memory range
+		   */
+
+	nand:cs2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <2>;
+		/* all timings in nanoseconds */
+		ti,cs-min-turnaround-ns = <0>;
+		ti,cs-read-hold-ns = <7>;
+		ti,cs-read-strobe-ns = <42>;
+		ti,cs-read-setup-ns = <14>;
+		ti,cs-write-hold-ns = <7>;
+		ti,cs-write-strobe-ns = <42>;
+		ti,cs-write-setup-ns = <14>;
+
+		nand@0,0x8000000 {
+			compatible = "ti,davinci-nand";
+			reg = <0 0x8000000 0x4000000
+			       1 0x0000000 0x0000100>;
+			/*
+			 * Partition0, offset 0x8000000, size 0x4000000
+			 * Partition1, offset 0x0000000, size 0x0000100
+			 */
+
+			.. see davinci-nand.txt
+		};
+	};
+
+	nor:cs0 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		clock-ranges;
+		ranges;
+
+		ti,cs-chipselect = <0>;
+		/* all timings in nanoseconds */
+		ti,cs-min-turnaround-ns = <0>;
+		ti,cs-read-hold-ns = <8>;
+		ti,cs-read-strobe-ns = <40>;
+		ti,cs-read-setup-ns = <14>;
+		ti,cs-write-hold-ns = <7>;
+		ti,cs-write-strobe-ns = <40>;
+		ti,cs-write-setup-ns = <14>;
+		ti,cs-bus-width = <16>;
+
+		flash@0,0x0000000 {
+			compatible = "cfi-flash";
+			reg = <0 0x0000000 0x4000000>;
+
+			...
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
new file mode 100644
index 000000000..63f674ffe
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
@@ -0,0 +1,84 @@
+* EMIF family of TI SDRAM controllers
+
+EMIF - External Memory Interface - is an SDRAM controller used in
+TI SoCs. EMIF supports, based on the IP revision, one or more of
+DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
+of the EMIF IP and memory parts attached to it. Certain revisions
+of the EMIF controller also contain optional ECC support, which
+corrects one bit errors and detects two bit errors.
+
+Required properties:
+- compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
+  is the IP revision of the specific EMIF instance. For newer controllers,
+  compatible should be one of the following:
+  	     "ti,emif-am3352"
+	     "ti,emif-am4372"
+	     "ti,emif-dra7xx"
+	     "ti,emif-keystone"
+
+- phy-type	: <u32> indicating the DDR phy type. Following are the
+  allowed values
+  <1>	: Attila PHY
+  <2>	: Intelli PHY
+
+- device-handle	: phandle to a "lpddr2" node representing the memory part
+
+- ti,hwmods	: For TI hwmods processing and omap device creation
+  the value shall be "emif<n>" where <n> is the number of the EMIF
+  instance with base 1.
+- interrupts	: interrupt used by the controller
+
+Required only for "ti,emif-am3352" and "ti,emif-am4372":
+- sram			: Phandles for generic sram driver nodes,
+  first should be type 'protect-exec' for the driver to use to copy
+  and run PM functions, second should be regular pool to be used for
+  data region for code. See Documentation/devicetree/bindings/sram/sram.yaml
+  for more details.
+
+Optional properties:
+- cs1-used		: Have this property if CS1 of this EMIF
+  instance has a memory part attached to it. If there is a memory
+  part attached to CS1, it should be the same type as the one on CS0,
+  so there is no need to give the details of this memory part.
+
+- cal-resistor-per-cs	: Have this property if the board has one
+  calibration resistor per chip-select.
+
+- hw-caps-read-idle-ctrl: Have this property if the controller
+  supports read idle window programming
+
+- hw-caps-dll-calib-ctrl: Have this property if the controller
+  supports dll calibration control
+
+- hw-caps-ll-interface	: Have this property if the controller
+  has a low latency interface and corresponding interrupt events
+
+- hw-caps-temp-alert	: Have this property if the controller
+  has capability for generating SDRAM temperature alerts
+
+-Examples:
+
+emif1: emif@4c000000 {
+	compatible	= "ti,emif-4d";
+	ti,hwmods	= "emif2";
+	phy-type	= <1>;
+	device-handle	= <&elpida_ECB240ABACN>;
+	cs1-used;
+	hw-caps-read-idle-ctrl;
+	hw-caps-ll-interface;
+	hw-caps-temp-alert;
+};
+
+/* From am33xx.dtsi */
+emif: emif@4c000000 {
+        compatible = "ti,emif-am3352";
+        reg =   <0x4C000000 0x1000>;
+        sram = <&pm_sram_code
+                &pm_sram_data>;
+};
+
+emif1: emif@4c000000 {
+	compatible = "ti,emif-dra7xx";
+	reg = <0x4c000000 0x200>;
+	interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+};