Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 620 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
new file mode 100644
index 000000000..7ae6aba5d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
@@ -0,0 +1,620 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */
+#define PMK8350_SID 6
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm7225.dtsi"
+#include "pm6150l.dtsi"
+#include "pm6350.dtsi"
+#include "pm7250b.dtsi"
+#include "pmk8350.dtsi"
+
+/ {
+	model = "Fairphone 4";
+	compatible = "fairphone,fp4", "qcom,sm7225";
+	chassis-type = "handset";
+
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <434 0x10000>, <459 0x10000>;
+	qcom,board-id = <8 32>;
+
+	aliases {
+		serial0 = &uart9;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0:115200n8";
+
+		framebuffer0: framebuffer@a000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0xa0000000 0 (2340 * 1080 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin>;
+
+		key-volume-up {
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reserved-memory {
+		/*
+		 * The rmtfs memory region in downstream is 'dynamically allocated'
+		 * but given the same address every time. Hard code it as this address is
+		 * where the modem firmware expects it to be.
+		 */
+		memory@efe01000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xefe01000 0 0x600000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+	};
+
+	thermal-zones {
+		chg-skin-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+};
+
+&adsp {
+	firmware-name = "qcom/sm7225/fairphone4/adsp.mdt";
+	status = "okay";
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm6350-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s1a: smps1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_s2a: smps2 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <2048000>;
+		};
+
+		vreg_l2a: ldo2 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a: ldo3 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4a: ldo4 {
+			regulator-min-microvolt = <352000>;
+			regulator-max-microvolt = <801000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a: ldo6 {
+			regulator-min-microvolt = <1710000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a: ldo9 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a: ldo11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a: ldo12 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-min-microvolt = <570000>;
+			regulator-max-microvolt = <650000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a: ldo14 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a: ldo15 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a: ldo16 {
+			regulator-min-microvolt = <830000>;
+			regulator-max-microvolt = <921000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a: ldo18 {
+			regulator-min-microvolt = <788000>;
+			regulator-max-microvolt = <1049000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a: ldo19 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a: ldo20 {
+			regulator-min-microvolt = <530000>;
+			regulator-max-microvolt = <801000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a: ldo21 {
+			regulator-min-microvolt = <751000>;
+			regulator-max-microvolt = <825000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a: ldo22 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm6150l-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s8e: smps8 {
+			regulator-min-microvolt = <313000>;
+			regulator-max-microvolt = <1395000>;
+		};
+
+		vreg_l1e: ldo1 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e: ldo2 {
+			regulator-min-microvolt = <1170000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e: ldo3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1299000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4e: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5e: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6e: ldo6 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7e: ldo7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8e: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9e: ldo9 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10e: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11e: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <5492000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+};
+
+&cci0 {
+	status = "okay";
+};
+
+&cci0_i2c0 {
+	/* IMX582 @ 0x1a */
+};
+
+&cci0_i2c1 {
+	/* IMX582 @ 0x1a */
+};
+
+&cci1 {
+	status = "okay";
+};
+
+&cci1_i2c0 {
+	/* IMX576 @ 0x10 */
+};
+
+&cdsp {
+	firmware-name = "qcom/sm7225/fairphone4/cdsp.mdt";
+	status = "okay";
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* ST21NFCD NFC @ 8 */
+	/* VL53L3 ToF @ 29 */
+	/* AW88264A amplifier @ 34 */
+	/* AW88264A amplifier @ 35 */
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* HX83112A touchscreen @ 48 */
+};
+
+&i2c10 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* PM8008 PMIC @ 8 and 9 */
+	/* PX8618 @ 26 */
+	/* SMB1395 PMIC @ 34 */
+
+	haptics@5a {
+		compatible = "awinic,aw8695";
+		reg = <0x5a>;
+		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+
+		awinic,f0-preset = <2350>;
+		awinic,f0-coefficient = <260>;
+		awinic,f0-calibration-percent = <7>;
+		awinic,drive-level = <125>;
+
+		awinic,f0-detection-play-time = <5>;
+		awinic,f0-detection-wait-time = <3>;
+		awinic,f0-detection-repeat = <2>;
+		awinic,f0-detection-trace = <15>;
+
+		awinic,boost-debug = /bits/ 8 <0x30 0xeb 0xd4>;
+		awinic,tset = /bits/ 8 <0x12>;
+		awinic,r-spare = /bits/ 8 <0x68>;
+
+		awinic,bemf-upper-threshold = <4104>;
+		awinic,bemf-lower-threshold = <1016>;
+	};
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&pil_ipa_fw_mem>;
+	firmware-name = "qcom/sm7225/fairphone4/ipa_fws.mdt";
+	status = "okay";
+};
+
+&mpss {
+	firmware-name = "qcom/sm7225/fairphone4/modem.mdt";
+	status = "okay";
+};
+
+&pm6150l_flash {
+	status = "okay";
+
+	led-0 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_YELLOW>;
+		led-sources = <1>;
+		led-max-microamp = <180000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+	};
+
+	led-1 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_WHITE>;
+		led-sources = <2>;
+		led-max-microamp = <180000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+	};
+};
+
+&pm6150l_wled {
+	qcom,switching-freq = <800>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+
+	status = "okay";
+};
+
+&pm6350_gpios {
+	gpio_keys_pin: gpio-keys-state {
+		pins = "gpio2";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-up;
+		input-enable;
+		power-source = <0>;
+	};
+};
+
+&pm6350_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm7250b_adc {
+	adc-chan@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "charger_skin_therm";
+	};
+
+	adc-chan@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "conn_therm";
+	};
+};
+
+&pm7250b_adc_tm {
+	status = "okay";
+
+	charger-skin-therm@0 {
+		reg = <0>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	conn-therm@1 {
+		reg = <1>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pmk8350_vadc {
+	adc-chan@644 {
+		reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "xo_therm";
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdc2_off_state {
+	sd-cd-pins {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd-pins {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&sdhc_2 {
+	vmmc-supply = <&vreg_l9e>;
+	vqmmc-supply = <&vreg_l6e>;
+
+	cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <13 4>, <56 2>;
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 156 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7e>;
+	vcc-max-microamp = <800000>;
+	vccq2-supply = <&vreg_l12a>;
+	vccq2-max-microamp = <800000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l18a>;
+	vdda-pll-supply = <&vreg_l22a>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	maximum-speed = "super-speed";
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l18a>;
+	vdda-pll-supply = <&vreg_l2a>;
+	vdda-phy-dpdm-supply = <&vreg_l3a>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l22a>;
+	vdda-pll-supply = <&vreg_l16a>;
+
+	status = "okay";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l4a>;
+	vdd-1.8-xo-supply = <&vreg_l7a>;
+	vdd-1.3-rfa-supply = <&vreg_l2e>;
+	vdd-3.3-ch0-supply = <&vreg_l10e>;
+	vdd-3.3-ch1-supply = <&vreg_l11e>;
+
+	status = "okay";
+};