Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 494 insertions, 0 deletions

diff --git a/drivers/net/wireless/ath/ath10k/targaddrs.h b/drivers/net/wireless/ath/ath10k/targaddrs.h
new file mode 100644
index 000000000..ec556bb88
--- /dev/null
+++ b/drivers/net/wireless/ath/ath10k/targaddrs.h
@@ -0,0 +1,494 @@
+/* SPDX-License-Identifier: ISC */
+/*
+ * Copyright (c) 2005-2011 Atheros Communications Inc.
+ * Copyright (c) 2011-2016 Qualcomm Atheros, Inc.
+ */
+
+#ifndef __TARGADDRS_H__
+#define __TARGADDRS_H__
+
+#include "hw.h"
+
+/*
+ * xxx_HOST_INTEREST_ADDRESS is the address in Target RAM of the
+ * host_interest structure.  It must match the address of the _host_interest
+ * symbol (see linker script).
+ *
+ * Host Interest is shared between Host and Target in order to coordinate
+ * between the two, and is intended to remain constant (with additions only
+ * at the end) across software releases.
+ *
+ * All addresses are available here so that it's possible to
+ * write a single binary that works with all Target Types.
+ * May be used in assembler code as well as C.
+ */
+#define QCA988X_HOST_INTEREST_ADDRESS    0x00400800
+#define HOST_INTEREST_MAX_SIZE          0x200
+
+/*
+ * These are items that the Host may need to access via BMI or via the
+ * Diagnostic Window. The position of items in this structure must remain
+ * constant across firmware revisions! Types for each item must be fixed
+ * size across target and host platforms. More items may be added at the end.
+ */
+struct host_interest {
+	/*
+	 * Pointer to application-defined area, if any.
+	 * Set by Target application during startup.
+	 */
+	u32 hi_app_host_interest;			/* 0x00 */
+
+	/* Pointer to register dump area, valid after Target crash. */
+	u32 hi_failure_state;				/* 0x04 */
+
+	/* Pointer to debug logging header */
+	u32 hi_dbglog_hdr;				/* 0x08 */
+
+	u32 hi_unused0c;				/* 0x0c */
+
+	/*
+	 * General-purpose flag bits, similar to SOC_OPTION_* flags.
+	 * Can be used by application rather than by OS.
+	 */
+	u32 hi_option_flag;				/* 0x10 */
+
+	/*
+	 * Boolean that determines whether or not to
+	 * display messages on the serial port.
+	 */
+	u32 hi_serial_enable;				/* 0x14 */
+
+	/* Start address of DataSet index, if any */
+	u32 hi_dset_list_head;				/* 0x18 */
+
+	/* Override Target application start address */
+	u32 hi_app_start;				/* 0x1c */
+
+	/* Clock and voltage tuning */
+	u32 hi_skip_clock_init;				/* 0x20 */
+	u32 hi_core_clock_setting;			/* 0x24 */
+	u32 hi_cpu_clock_setting;			/* 0x28 */
+	u32 hi_system_sleep_setting;			/* 0x2c */
+	u32 hi_xtal_control_setting;			/* 0x30 */
+	u32 hi_pll_ctrl_setting_24ghz;			/* 0x34 */
+	u32 hi_pll_ctrl_setting_5ghz;			/* 0x38 */
+	u32 hi_ref_voltage_trim_setting;		/* 0x3c */
+	u32 hi_clock_info;				/* 0x40 */
+
+	/* Host uses BE CPU or not */
+	u32 hi_be;					/* 0x44 */
+
+	u32 hi_stack;	/* normal stack */			/* 0x48 */
+	u32 hi_err_stack; /* error stack */		/* 0x4c */
+	u32 hi_desired_cpu_speed_hz;			/* 0x50 */
+
+	/* Pointer to Board Data  */
+	u32 hi_board_data;				/* 0x54 */
+
+	/*
+	 * Indication of Board Data state:
+	 *    0: board data is not yet initialized.
+	 *    1: board data is initialized; unknown size
+	 *   >1: number of bytes of initialized board data
+	 */
+	u32 hi_board_data_initialized;			/* 0x58 */
+
+	u32 hi_dset_ram_index_table;			/* 0x5c */
+
+	u32 hi_desired_baud_rate;			/* 0x60 */
+	u32 hi_dbglog_config;				/* 0x64 */
+	u32 hi_end_ram_reserve_sz;			/* 0x68 */
+	u32 hi_mbox_io_block_sz;			/* 0x6c */
+
+	u32 hi_num_bpatch_streams;			/* 0x70 -- unused */
+	u32 hi_mbox_isr_yield_limit;			/* 0x74 */
+
+	u32 hi_refclk_hz;				/* 0x78 */
+	u32 hi_ext_clk_detected;			/* 0x7c */
+	u32 hi_dbg_uart_txpin;				/* 0x80 */
+	u32 hi_dbg_uart_rxpin;				/* 0x84 */
+	u32 hi_hci_uart_baud;				/* 0x88 */
+	u32 hi_hci_uart_pin_assignments;		/* 0x8C */
+
+	u32 hi_hci_uart_baud_scale_val;			/* 0x90 */
+	u32 hi_hci_uart_baud_step_val;			/* 0x94 */
+
+	u32 hi_allocram_start;				/* 0x98 */
+	u32 hi_allocram_sz;				/* 0x9c */
+	u32 hi_hci_bridge_flags;			/* 0xa0 */
+	u32 hi_hci_uart_support_pins;			/* 0xa4 */
+
+	u32 hi_hci_uart_pwr_mgmt_params;		/* 0xa8 */
+
+	/*
+	 * 0xa8 - [1]: 0 = UART FC active low, 1 = UART FC active high
+	 *        [31:16]: wakeup timeout in ms
+	 */
+	/* Pointer to extended board Data  */
+	u32 hi_board_ext_data;				/* 0xac */
+	u32 hi_board_ext_data_config;			/* 0xb0 */
+	/*
+	 * Bit [0]  :   valid
+	 * Bit[31:16:   size
+	 */
+	/*
+	 * hi_reset_flag is used to do some stuff when target reset.
+	 * such as restore app_start after warm reset or
+	 * preserve host Interest area, or preserve ROM data, literals etc.
+	 */
+	u32  hi_reset_flag;				/* 0xb4 */
+	/* indicate hi_reset_flag is valid */
+	u32  hi_reset_flag_valid;			/* 0xb8 */
+	u32 hi_hci_uart_pwr_mgmt_params_ext;		/* 0xbc */
+	/* 0xbc - [31:0]: idle timeout in ms */
+	/* ACS flags */
+	u32 hi_acs_flags;				/* 0xc0 */
+	u32 hi_console_flags;				/* 0xc4 */
+	u32 hi_nvram_state;				/* 0xc8 */
+	u32 hi_option_flag2;				/* 0xcc */
+
+	/* If non-zero, override values sent to Host in WMI_READY event. */
+	u32 hi_sw_version_override;			/* 0xd0 */
+	u32 hi_abi_version_override;			/* 0xd4 */
+
+	/*
+	 * Percentage of high priority RX traffic to total expected RX traffic
+	 * applicable only to ar6004
+	 */
+	u32 hi_hp_rx_traffic_ratio;			/* 0xd8 */
+
+	/* test applications flags */
+	u32 hi_test_apps_related;			/* 0xdc */
+	/* location of test script */
+	u32 hi_ota_testscript;				/* 0xe0 */
+	/* location of CAL data */
+	u32 hi_cal_data;				/* 0xe4 */
+
+	/* Number of packet log buffers */
+	u32 hi_pktlog_num_buffers;			/* 0xe8 */
+
+	/* wow extension configuration */
+	u32 hi_wow_ext_config;				/* 0xec */
+	u32 hi_pwr_save_flags;				/* 0xf0 */
+
+	/* Spatial Multiplexing Power Save (SMPS) options */
+	u32 hi_smps_options;				/* 0xf4 */
+
+	/* Interconnect-specific state */
+	u32 hi_interconnect_state;			/* 0xf8 */
+
+	/* Coex configuration flags */
+	u32 hi_coex_config;				/* 0xfc */
+
+	/* Early allocation support */
+	u32 hi_early_alloc;				/* 0x100 */
+	/* FW swap field */
+	/*
+	 * Bits of this 32bit word will be used to pass specific swap
+	 * instruction to FW
+	 */
+	/*
+	 * Bit 0 -- AP Nart descriptor no swap. When this bit is set
+	 * FW will not swap TX descriptor. Meaning packets are formed
+	 * on the target processor.
+	 */
+	/* Bit 1 - unused */
+	u32 hi_fw_swap;					/* 0x104 */
+
+	/* global arenas pointer address, used by host driver debug */
+	u32 hi_dynamic_mem_arenas_addr;			/* 0x108 */
+
+	/* allocated bytes of DRAM use by allocated */
+	u32 hi_dynamic_mem_allocated;			/* 0x10C */
+
+	/* remaining bytes of DRAM */
+	u32 hi_dynamic_mem_remaining;			/* 0x110 */
+
+	/* memory track count, configured by host */
+	u32 hi_dynamic_mem_track_max;			/* 0x114 */
+
+	/* minidump buffer */
+	u32 hi_minidump;				/* 0x118 */
+
+	/* bdata's sig and key addr */
+	u32 hi_bd_sig_key;				/* 0x11c */
+} __packed;
+
+#define HI_ITEM(item)  offsetof(struct host_interest, item)
+
+/* Bits defined in hi_option_flag */
+
+/* Enable timer workaround */
+#define HI_OPTION_TIMER_WAR         0x01
+/* Limit BMI command credits */
+#define HI_OPTION_BMI_CRED_LIMIT    0x02
+/* Relay Dot11 hdr to/from host */
+#define HI_OPTION_RELAY_DOT11_HDR   0x04
+/* MAC addr method 0-locally administred 1-globally unique addrs */
+#define HI_OPTION_MAC_ADDR_METHOD   0x08
+/* Firmware Bridging */
+#define HI_OPTION_FW_BRIDGE         0x10
+/* Enable CPU profiling */
+#define HI_OPTION_ENABLE_PROFILE    0x20
+/* Disable debug logging */
+#define HI_OPTION_DISABLE_DBGLOG    0x40
+/* Skip Era Tracking */
+#define HI_OPTION_SKIP_ERA_TRACKING 0x80
+/* Disable PAPRD (debug) */
+#define HI_OPTION_PAPRD_DISABLE     0x100
+#define HI_OPTION_NUM_DEV_LSB       0x200
+#define HI_OPTION_NUM_DEV_MSB       0x800
+#define HI_OPTION_DEV_MODE_LSB      0x1000
+#define HI_OPTION_DEV_MODE_MSB      0x8000000
+/* Disable LowFreq Timer Stabilization */
+#define HI_OPTION_NO_LFT_STBL       0x10000000
+/* Skip regulatory scan */
+#define HI_OPTION_SKIP_REG_SCAN     0x20000000
+/*
+ * Do regulatory scan during init before
+ * sending WMI ready event to host
+ */
+#define HI_OPTION_INIT_REG_SCAN     0x40000000
+
+/* REV6: Do not adjust memory map */
+#define HI_OPTION_SKIP_MEMMAP       0x80000000
+
+#define HI_OPTION_MAC_ADDR_METHOD_SHIFT 3
+
+/* 2 bits of hi_option_flag are used to represent 3 modes */
+#define HI_OPTION_FW_MODE_IBSS    0x0 /* IBSS Mode */
+#define HI_OPTION_FW_MODE_BSS_STA 0x1 /* STA Mode */
+#define HI_OPTION_FW_MODE_AP      0x2 /* AP Mode */
+#define HI_OPTION_FW_MODE_BT30AMP 0x3 /* BT30 AMP Mode */
+
+/* 2 bits of hi_option flag are usedto represent 4 submodes */
+#define HI_OPTION_FW_SUBMODE_NONE    0x0  /* Normal mode */
+#define HI_OPTION_FW_SUBMODE_P2PDEV  0x1  /* p2p device mode */
+#define HI_OPTION_FW_SUBMODE_P2PCLIENT 0x2 /* p2p client mode */
+#define HI_OPTION_FW_SUBMODE_P2PGO   0x3 /* p2p go mode */
+
+/* Num dev Mask */
+#define HI_OPTION_NUM_DEV_MASK    0x7
+#define HI_OPTION_NUM_DEV_SHIFT   0x9
+
+/* firmware bridging */
+#define HI_OPTION_FW_BRIDGE_SHIFT 0x04
+
+/*
+ * Fw Mode/SubMode Mask
+ *-----------------------------------------------------------------------------
+ *  SUB   |   SUB   |   SUB   |  SUB    |         |         |         |
+ *MODE[3] | MODE[2] | MODE[1] | MODE[0] | MODE[3] | MODE[2] | MODE[1] | MODE[0]
+ *  (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)   |   (2)
+ *-----------------------------------------------------------------------------
+ */
+#define HI_OPTION_FW_MODE_BITS         0x2
+#define HI_OPTION_FW_MODE_MASK         0x3
+#define HI_OPTION_FW_MODE_SHIFT        0xC
+#define HI_OPTION_ALL_FW_MODE_MASK     0xFF
+
+#define HI_OPTION_FW_SUBMODE_BITS      0x2
+#define HI_OPTION_FW_SUBMODE_MASK      0x3
+#define HI_OPTION_FW_SUBMODE_SHIFT     0x14
+#define HI_OPTION_ALL_FW_SUBMODE_MASK  0xFF00
+#define HI_OPTION_ALL_FW_SUBMODE_SHIFT 0x8
+
+/* hi_option_flag2 options */
+#define HI_OPTION_OFFLOAD_AMSDU     0x01
+#define HI_OPTION_DFS_SUPPORT       0x02 /* Enable DFS support */
+#define HI_OPTION_ENABLE_RFKILL     0x04 /* RFKill Enable Feature*/
+#define HI_OPTION_RADIO_RETENTION_DISABLE 0x08 /* Disable radio retention */
+#define HI_OPTION_EARLY_CFG_DONE    0x10 /* Early configuration is complete */
+
+#define HI_OPTION_RF_KILL_SHIFT     0x2
+#define HI_OPTION_RF_KILL_MASK      0x1
+
+/* hi_reset_flag */
+/* preserve App Start address */
+#define HI_RESET_FLAG_PRESERVE_APP_START         0x01
+/* preserve host interest */
+#define HI_RESET_FLAG_PRESERVE_HOST_INTEREST     0x02
+/* preserve ROM data */
+#define HI_RESET_FLAG_PRESERVE_ROMDATA           0x04
+#define HI_RESET_FLAG_PRESERVE_NVRAM_STATE       0x08
+#define HI_RESET_FLAG_PRESERVE_BOOT_INFO         0x10
+#define HI_RESET_FLAG_WARM_RESET	0x20
+
+/* define hi_fw_swap bits */
+#define HI_DESC_IN_FW_BIT	0x01
+
+/* indicate the reset flag is valid */
+#define HI_RESET_FLAG_IS_VALID  0x12345678
+
+/* ACS is enabled */
+#define HI_ACS_FLAGS_ENABLED        (1 << 0)
+/* Use physical WWAN device */
+#define HI_ACS_FLAGS_USE_WWAN       (1 << 1)
+/* Use test VAP */
+#define HI_ACS_FLAGS_TEST_VAP       (1 << 2)
+/* SDIO/mailbox ACS flag definitions */
+#define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_SET       (1 << 0)
+#define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_SET    (1 << 1)
+#define HI_ACS_FLAGS_ALT_DATA_CREDIT_SIZE        (1 << 2)
+#define HI_ACS_FLAGS_SDIO_SWAP_MAILBOX_FW_ACK    (1 << 16)
+#define HI_ACS_FLAGS_SDIO_REDUCE_TX_COMPL_FW_ACK (1 << 17)
+
+/*
+ * If both SDIO_CRASH_DUMP_ENHANCEMENT_HOST and SDIO_CRASH_DUMP_ENHANCEMENT_FW
+ * flags are set, then crashdump upload will be done using the BMI host/target
+ * communication channel.
+ */
+/* HOST to support using BMI dump FW memory when hit assert */
+#define HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_HOST 0x400
+
+/* FW to support using BMI dump FW memory when hit assert */
+#define HI_OPTION_SDIO_CRASH_DUMP_ENHANCEMENT_FW   0x800
+
+/*
+ * CONSOLE FLAGS
+ *
+ * Bit Range  Meaning
+ * ---------  --------------------------------
+ *   2..0     UART ID (0 = Default)
+ *    3       Baud Select (0 = 9600, 1 = 115200)
+ *   30..4    Reserved
+ *    31      Enable Console
+ *
+ */
+
+#define HI_CONSOLE_FLAGS_ENABLE       (1 << 31)
+#define HI_CONSOLE_FLAGS_UART_MASK    (0x7)
+#define HI_CONSOLE_FLAGS_UART_SHIFT   0
+#define HI_CONSOLE_FLAGS_BAUD_SELECT  (1 << 3)
+
+/* SM power save options */
+#define HI_SMPS_ALLOW_MASK            (0x00000001)
+#define HI_SMPS_MODE_MASK             (0x00000002)
+#define HI_SMPS_MODE_STATIC           (0x00000000)
+#define HI_SMPS_MODE_DYNAMIC          (0x00000002)
+#define HI_SMPS_DISABLE_AUTO_MODE     (0x00000004)
+#define HI_SMPS_DATA_THRESH_MASK      (0x000007f8)
+#define HI_SMPS_DATA_THRESH_SHIFT     (3)
+#define HI_SMPS_RSSI_THRESH_MASK      (0x0007f800)
+#define HI_SMPS_RSSI_THRESH_SHIFT     (11)
+#define HI_SMPS_LOWPWR_CM_MASK        (0x00380000)
+#define HI_SMPS_LOWPWR_CM_SHIFT       (15)
+#define HI_SMPS_HIPWR_CM_MASK         (0x03c00000)
+#define HI_SMPS_HIPWR_CM_SHIFT        (19)
+
+/*
+ * WOW Extension configuration
+ *
+ * Bit Range  Meaning
+ * ---------  --------------------------------
+ *   8..0     Size of each WOW pattern (max 511)
+ *   15..9    Number of patterns per list (max 127)
+ *   17..16   Number of lists (max 4)
+ *   30..18   Reserved
+ *   31       Enabled
+ *
+ *  set values (except enable) to zeros for default settings
+ */
+
+#define HI_WOW_EXT_ENABLED_MASK        (1 << 31)
+#define HI_WOW_EXT_NUM_LIST_SHIFT      16
+#define HI_WOW_EXT_NUM_LIST_MASK       (0x3 << HI_WOW_EXT_NUM_LIST_SHIFT)
+#define HI_WOW_EXT_NUM_PATTERNS_SHIFT  9
+#define HI_WOW_EXT_NUM_PATTERNS_MASK   (0x7F << HI_WOW_EXT_NUM_PATTERNS_SHIFT)
+#define HI_WOW_EXT_PATTERN_SIZE_SHIFT  0
+#define HI_WOW_EXT_PATTERN_SIZE_MASK   (0x1FF << HI_WOW_EXT_PATTERN_SIZE_SHIFT)
+
+#define HI_WOW_EXT_MAKE_CONFIG(num_lists, count, size) \
+	((((num_lists) << HI_WOW_EXT_NUM_LIST_SHIFT) & \
+		HI_WOW_EXT_NUM_LIST_MASK) | \
+	(((count) << HI_WOW_EXT_NUM_PATTERNS_SHIFT) & \
+		HI_WOW_EXT_NUM_PATTERNS_MASK) | \
+	(((size) << HI_WOW_EXT_PATTERN_SIZE_SHIFT) & \
+		HI_WOW_EXT_PATTERN_SIZE_MASK))
+
+#define HI_WOW_EXT_GET_NUM_LISTS(config) \
+	(((config) & HI_WOW_EXT_NUM_LIST_MASK) >> HI_WOW_EXT_NUM_LIST_SHIFT)
+#define HI_WOW_EXT_GET_NUM_PATTERNS(config) \
+	(((config) & HI_WOW_EXT_NUM_PATTERNS_MASK) >> \
+		HI_WOW_EXT_NUM_PATTERNS_SHIFT)
+#define HI_WOW_EXT_GET_PATTERN_SIZE(config) \
+	(((config) & HI_WOW_EXT_PATTERN_SIZE_MASK) >> \
+		HI_WOW_EXT_PATTERN_SIZE_SHIFT)
+
+/*
+ * Early allocation configuration
+ * Support RAM bank configuration before BMI done and this eases the memory
+ * allocation at very early stage
+ * Bit Range  Meaning
+ * ---------  ----------------------------------
+ * [0:3]      number of bank assigned to be IRAM
+ * [4:15]     reserved
+ * [16:31]    magic number
+ *
+ * Note:
+ * 1. target firmware would check magic number and if it's a match, firmware
+ *    would consider the bits[0:15] are valid and base on that to calculate
+ *    the end of DRAM. Early allocation would be located at that area and
+ *    may be reclaimed when necessary
+ * 2. if no magic number is found, early allocation would happen at "_end"
+ *    symbol of ROM which is located before the app-data and might NOT be
+ *    re-claimable. If this is adopted, link script should keep this in
+ *    mind to avoid data corruption.
+ */
+#define HI_EARLY_ALLOC_MAGIC		0x6d8a
+#define HI_EARLY_ALLOC_MAGIC_MASK	0xffff0000
+#define HI_EARLY_ALLOC_MAGIC_SHIFT	16
+#define HI_EARLY_ALLOC_IRAM_BANKS_MASK	0x0000000f
+#define HI_EARLY_ALLOC_IRAM_BANKS_SHIFT	0
+
+#define HI_EARLY_ALLOC_VALID() \
+	((((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_MAGIC_MASK) >> \
+	HI_EARLY_ALLOC_MAGIC_SHIFT) == (HI_EARLY_ALLOC_MAGIC))
+#define HI_EARLY_ALLOC_GET_IRAM_BANKS() \
+	(((HOST_INTEREST->hi_early_alloc) & HI_EARLY_ALLOC_IRAM_BANKS_MASK) \
+	>> HI_EARLY_ALLOC_IRAM_BANKS_SHIFT)
+
+/*power save flag bit definitions*/
+#define HI_PWR_SAVE_LPL_ENABLED   0x1
+/*b1-b3 reserved*/
+/*b4-b5 : dev0 LPL type : 0 - none
+ *			  1- Reduce Pwr Search
+ *			  2- Reduce Pwr Listen
+ */
+/*b6-b7 : dev1 LPL type and so on for Max 8 devices*/
+#define HI_PWR_SAVE_LPL_DEV0_LSB   4
+#define HI_PWR_SAVE_LPL_DEV_MASK   0x3
+/*power save related utility macros*/
+#define HI_LPL_ENABLED() \
+	((HOST_INTEREST->hi_pwr_save_flags & HI_PWR_SAVE_LPL_ENABLED))
+#define HI_DEV_LPL_TYPE_GET(_devix) \
+	(HOST_INTEREST->hi_pwr_save_flags & ((HI_PWR_SAVE_LPL_DEV_MASK) << \
+	 (HI_PWR_SAVE_LPL_DEV0_LSB + (_devix) * 2)))
+
+#define HOST_INTEREST_SMPS_IS_ALLOWED() \
+	((HOST_INTEREST->hi_smps_options & HI_SMPS_ALLOW_MASK))
+
+/* Reserve 1024 bytes for extended board data */
+#define QCA988X_BOARD_DATA_SZ     7168
+#define QCA988X_BOARD_EXT_DATA_SZ 0
+
+#define QCA9887_BOARD_DATA_SZ     7168
+#define QCA9887_BOARD_EXT_DATA_SZ 0
+
+#define QCA6174_BOARD_DATA_SZ     8192
+#define QCA6174_BOARD_EXT_DATA_SZ 0
+
+#define QCA9377_BOARD_DATA_SZ     QCA6174_BOARD_DATA_SZ
+#define QCA9377_BOARD_EXT_DATA_SZ 0
+
+#define QCA99X0_BOARD_DATA_SZ	  12288
+#define QCA99X0_BOARD_EXT_DATA_SZ 0
+
+/* Dual band extended board data */
+#define QCA99X0_EXT_BOARD_DATA_SZ 2048
+#define EXT_BOARD_ADDRESS_OFFSET 0x3000
+
+#define QCA4019_BOARD_DATA_SZ	  12064
+#define QCA4019_BOARD_EXT_DATA_SZ 0
+
+#endif /* __TARGADDRS_H__ */