From 5b7c4cabbb65f5c469464da6c5f614cbd7f730f2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 21 Feb 2023 18:24:12 -0800 Subject: Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core: - Add dedicated kmem_cache for typical/small skb->head, avoid having to access struct page at kfree time, and improve memory use. - Introduce sysctl to set default RPS configuration for new netdevs. - Define Netlink protocol specification format which can be used to describe messages used by each family and auto-generate parsers. Add tools for generating kernel data structures and uAPI headers. - Expose all net/core sysctls inside netns. - Remove 4s sleep in netpoll if carrier is instantly detected on boot. - Add configurable limit of MDB entries per port, and port-vlan. - Continue populating drop reasons throughout the stack. - Retire a handful of legacy Qdiscs and classifiers. Protocols: - Support IPv4 big TCP (TSO frames larger than 64kB). - Add IP_LOCAL_PORT_RANGE socket option, to control local port range on socket by socket basis. - Track and report in procfs number of MPTCP sockets used. - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path manager. - IPv6: don't check net.ipv6.route.max_size and rely on garbage collection to free memory (similarly to IPv4). - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986). - ICMP: add per-rate limit counters. - Add support for user scanning requests in ieee802154. - Remove static WEP support. - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting. - WiFi 7 EHT channel puncturing support (client & AP). BPF: - Add a rbtree data structure following the "next-gen data structure" precedent set by recently added linked list, that is, by using kfunc + kptr instead of adding a new BPF map type. - Expose XDP hints via kfuncs with initial support for RX hash and timestamp metadata. - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to better support decap on GRE tunnel devices not operating in collect metadata. - Improve x86 JIT's codegen for PROBE_MEM runtime error checks. - Remove the need for trace_printk_lock for bpf_trace_printk and bpf_trace_vprintk helpers. - Extend libbpf's bpf_tracing.h support for tracing arguments of kprobes/uprobes and syscall as a special case. - Significantly reduce the search time for module symbols by livepatch and BPF. - Enable cpumasks to be used as kptrs, which is useful for tracing programs tracking which tasks end up running on which CPUs in different time intervals. - Add support for BPF trampoline on s390x and riscv64. - Add capability to export the XDP features supported by the NIC. - Add __bpf_kfunc tag for marking kernel functions as kfuncs. - Add cgroup.memory=nobpf kernel parameter option to disable BPF memory accounting for container environments. Netfilter: - Remove the CLUSTERIP target. It has been marked as obsolete for years, and we still have WARN splats wrt races of the out-of-band /proc interface installed by this target. - Add 'destroy' commands to nf_tables. They are identical to the existing 'delete' commands, but do not return an error if the referenced object (set, chain, rule...) did not exist. Driver API: - Improve cpumask_local_spread() locality to help NICs set the right IRQ affinity on AMD platforms. - Separate C22 and C45 MDIO bus transactions more clearly. - Introduce new DCB table to control DSCP rewrite on egress. - Support configuration of Physical Layer Collision Avoidance (PLCA) Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of shared medium Ethernet. - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing preemption of low priority frames by high priority frames. - Add support for controlling MACSec offload using netlink SET. - Rework devlink instance refcounts to allow registration and de-registration under the instance lock. Split the code into multiple files, drop some of the unnecessarily granular locks and factor out common parts of netlink operation handling. - Add TX frame aggregation parameters (for USB drivers). - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning messages with notifications for debug. - Allow offloading of UDP NEW connections via act_ct. - Add support for per action HW stats in TC. - Support hardware miss to TC action (continue processing in SW from a specific point in the action chain). - Warn if old Wireless Extension user space interface is used with modern cfg80211/mac80211 drivers. Do not support Wireless Extensions for Wi-Fi 7 devices at all. Everyone should switch to using nl80211 interface instead. - Improve the CAN bit timing configuration. Use extack to return error messages directly to user space, update the SJW handling, including the definition of a new default value that will benefit CAN-FD controllers, by increasing their oscillator tolerance. New hardware / drivers: - Ethernet: - nVidia BlueField-3 support (control traffic driver) - Ethernet support for imx93 SoCs - Motorcomm yt8531 gigabit Ethernet PHY - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA) - Microchip LAN8841 PHY (incl. cable diagnostics and PTP) - Amlogic gxl MDIO mux - WiFi: - RealTek RTL8188EU (rtl8xxxu) - Qualcomm Wi-Fi 7 devices (ath12k) - CAN: - Renesas R-Car V4H Drivers: - Bluetooth: - Set Per Platform Antenna Gain (PPAG) for Intel controllers. - Ethernet NICs: - Intel (1G, igc): - support TSN / Qbv / packet scheduling features of i226 model - Intel (100G, ice): - use GNSS subsystem instead of TTY - multi-buffer XDP support - extend support for GPIO pins to E823 devices - nVidia/Mellanox: - update the shared buffer configuration on PFC commands - implement PTP adjphase function for HW offset control - TC support for Geneve and GRE with VF tunnel offload - more efficient crypto key management method - multi-port eswitch support - Netronome/Corigine: - add DCB IEEE support - support IPsec offloading for NFP3800 - Freescale/NXP (enetc): - support XDP_REDIRECT for XDP non-linear buffers - improve reconfig, avoid link flap and waiting for idle - support MAC Merge layer - Other NICs: - sfc/ef100: add basic devlink support for ef100 - ionic: rx_push mode operation (writing descriptors via MMIO) - bnxt: use the auxiliary bus abstraction for RDMA - r8169: disable ASPM and reset bus in case of tx timeout - cpsw: support QSGMII mode for J721e CPSW9G - cpts: support pulse-per-second output - ngbe: add an mdio bus driver - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing - r8152: handle devices with FW with NCM support - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation - virtio-net: support multi buffer XDP - virtio/vsock: replace virtio_vsock_pkt with sk_buff - tsnep: XDP support - Ethernet high-speed switches: - nVidia/Mellanox (mlxsw): - add support for latency TLV (in FW control messages) - Microchip (sparx5): - separate explicit and implicit traffic forwarding rules, make the implicit rules always active - add support for egress DSCP rewrite - IS0 VCAP support (Ingress Classification) - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.) - ES2 VCAP support (Egress Access Control) - support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1) - Ethernet embedded switches: - Marvell (mv88e6xxx): - add MAB (port auth) offload support - enable PTP receive for mv88e6390 - NXP (ocelot): - support MAC Merge layer - support for the the vsc7512 internal copper phys - Microchip: - lan9303: convert to PHYLINK - lan966x: support TC flower filter statistics - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x - lan937x: support Credit Based Shaper configuration - ksz9477: support Energy Efficient Ethernet - other: - qca8k: convert to regmap read/write API, use bulk operations - rswitch: Improve TX timestamp accuracy - Intel WiFi (iwlwifi): - EHT (Wi-Fi 7) rate reporting - STEP equalizer support: transfer some STEP (connection to radio on platforms with integrated wifi) related parameters from the BIOS to the firmware. - Qualcomm 802.11ax WiFi (ath11k): - IPQ5018 support - Fine Timing Measurement (FTM) responder role support - channel 177 support - MediaTek WiFi (mt76): - per-PHY LED support - mt7996: EHT (Wi-Fi 7) support - Wireless Ethernet Dispatch (WED) reset support - switch to using page pool allocator - RealTek WiFi (rtw89): - support new version of Bluetooth co-existance - Mobile: - rmnet: support TX aggregation" * tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits) page_pool: add a comment explaining the fragment counter usage net: ethtool: fix __ethtool_dev_mm_supported() implementation ethtool: pse-pd: Fix double word in comments xsk: add linux/vmalloc.h to xsk.c sefltests: netdevsim: wait for devlink instance after netns removal selftest: fib_tests: Always cleanup before exit net/mlx5e: Align IPsec ASO result memory to be as required by hardware net/mlx5e: TC, Set CT miss to the specific ct action instance net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG net/mlx5: Refactor tc miss handling to a single function net/mlx5: Kconfig: Make tc offload depend on tc skb extension net/sched: flower: Support hardware miss to tc action net/sched: flower: Move filter handle initialization earlier net/sched: cls_api: Support hardware miss to tc action net/sched: Rename user cookie and act cookie sfc: fix builds without CONFIG_RTC_LIB sfc: clean up some inconsistent indentings net/mlx4_en: Introduce flexible array to silence overflow warning net: lan966x: Fix possible deadlock inside PTP net/ulp: Remove redundant ->clone() test in inet_clone_ulp(). ... --- .../bindings/arm/msm/qcom,idle-state.txt | 84 ++++++++++++++++++++++ .../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 49 +++++++++++++ .../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 44 ++++++++++++ .../devicetree/bindings/arm/msm/qcom,llcc.yaml | 65 +++++++++++++++++ .../devicetree/bindings/arm/msm/qcom,saw2.txt | 58 +++++++++++++++ Documentation/devicetree/bindings/arm/msm/ssbi.txt | 18 +++++ 6 files changed, 318 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt create mode 100644 Documentation/devicetree/bindings/arm/msm/ssbi.txt (limited to 'Documentation/devicetree/bindings/arm/msm') diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt new file mode 100644 index 000000000..606b4b1b7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt @@ -0,0 +1,84 @@ +QCOM Idle States for cpuidle driver + +ARM provides idle-state node to define the cpuidle states, as defined in [1]. +cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle +states. Idle states have different enter/exit latency and residency values. +The idle states supported by the QCOM SoC are defined as - + + * Standby + * Retention + * Standalone Power Collapse (Standalone PC or SPC) + * Power Collapse (PC) + +Standby: Standby does a little more in addition to architectural clock gating. +When the WFI instruction is executed the ARM core would gate its internal +clocks. In addition to gating the clocks, QCOM cpus use this instruction as a +trigger to execute the SPM state machine. The SPM state machine waits for the +interrupt to trigger the core back in to active. This triggers the cache +hierarchy to enter standby states, when all cpus are idle. An interrupt brings +the SPM state machine out of its wait, the next step is to ensure that the +cache hierarchy is also out of standby, and then the cpu is allowed to resume +execution. This state is defined as a generic ARM WFI state by the ARM cpuidle +driver and is not defined in the DT. The SPM state machine should be +configured to execute this state by default and after executing every other +state below. + +Retention: Retention is a low power state where the core is clock gated and +the memory and the registers associated with the core are retained. The +voltage may be reduced to the minimum value needed to keep the processor +registers active. The SPM should be configured to execute the retention +sequence and would wait for interrupt, before restoring the cpu to execution +state. Retention may have a slightly higher latency than Standby. + +Standalone PC: A cpu can power down and warmboot if there is a sufficient time +between the time it enters idle and the next known wake up. SPC mode is used +to indicate a core entering a power down state without consulting any other +cpu or the system resources. This helps save power only on that core. The SPM +sequence for this idle state is programmed to power down the supply to the +core, wait for the interrupt, restore power to the core, and ensure the +system state including cache hierarchy is ready before allowing core to +resume. Applying power and resetting the core causes the core to warmboot +back into Elevation Level (EL) which trampolines the control back to the +kernel. Entering a power down state for the cpu, needs to be done by trapping +into a EL. Failing to do so, would result in a crash enforced by the warm boot +code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to +be flushed in s/w, before powering down the core. + +Power Collapse: This state is similar to the SPC mode, but distinguishes +itself in that the cpu acknowledges and permits the SoC to enter deeper sleep +modes. In a hierarchical power domain SoC, this means L2 and other caches can +be flushed, system bus, clocks - lowered, and SoC main XO clock gated and +voltages reduced, provided all cpus enter this state. Since the span of low +power modes possible at this state is vast, the exit latency and the residency +of this low power mode would be considered high even though at a cpu level, +this essentially is cpu power down. The SPM in this state also may handshake +with the Resource power manager (RPM) processor in the SoC to indicate a +complete application processor subsystem shut down. + +The idle-state for QCOM SoCs are distinguished by the compatible property of +the idle-states device node. + +The devicetree representation of the idle state should be - + +Required properties: + +- compatible: Must be one of - + "qcom,idle-state-ret", + "qcom,idle-state-spc", + "qcom,idle-state-pc", + and "arm,idle-state". + +Other required and optional properties are specified in [1]. + +Example: + + idle-states { + CPU_SPC: spc { + compatible = "qcom,idle-state-spc", "arm,idle-state"; + entry-latency-us = <150>; + exit-latency-us = <200>; + min-residency-us = <2000>; + }; + }; + +[1]. Documentation/devicetree/bindings/cpu/idle-states.yaml diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt new file mode 100644 index 000000000..7f696362a --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt @@ -0,0 +1,49 @@ +Krait Processor Sub-system (KPSS) Application Clock Controller (ACC) + +The KPSS ACC provides clock, power domain, and reset control to a Krait CPU. +There is one ACC register region per CPU within the KPSS remapped region as +well as an alias register region that remaps accesses to the ACC associated +with the CPU accessing the region. + +PROPERTIES + +- compatible: + Usage: required + Value type: + Definition: should be one of: + "qcom,kpss-acc-v1" + "qcom,kpss-acc-v2" + +- reg: + Usage: required + Value type: + Definition: the first element specifies the base address and size of + the register region. An optional second element specifies + the base address and size of the alias register region. + +- clocks: + Usage: required + Value type: + Definition: reference to the pll parents. + +- clock-names: + Usage: required + Value type: + Definition: must be "pll8_vote", "pxo". + +- clock-output-names: + Usage: optional + Value type: + Definition: Name of the output clock. Typically acpuX_aux where X is a + CPU number starting at 0. + +Example: + + clock-controller@2088000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0x02088000 0x1000>, + <0x02008000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu0_aux"; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt new file mode 100644 index 000000000..e62875895 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt @@ -0,0 +1,44 @@ +Krait Processor Sub-system (KPSS) Global Clock Controller (GCC) + +PROPERTIES + +- compatible: + Usage: required + Value type: + Definition: should be one of the following. The generic compatible + "qcom,kpss-gcc" should also be included. + "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc" + "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc" + "qcom,kpss-gcc-msm8974", "qcom,kpss-gcc" + "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc" + +- reg: + Usage: required + Value type: + Definition: base address and size of the register region + +- clocks: + Usage: required + Value type: + Definition: reference to the pll parents. + +- clock-names: + Usage: required + Value type: + Definition: must be "pll8_vote", "pxo". + +- clock-output-names: + Usage: required + Value type: + Definition: Name of the output clock. Typically acpu_l2_aux indicating + an L2 cache auxiliary clock. + +Example: + + l2cc: clock-controller@2011000 { + compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc"; + reg = <0x2011000 0x1000>; + clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; + clock-names = "pll8_vote", "pxo"; + clock-output-names = "acpu_l2_aux"; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml new file mode 100644 index 000000000..38efcad56 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/msm/qcom,llcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Last Level Cache Controller + +maintainers: + - Rishabh Bhatnagar + - Sai Prakash Ranjan + +description: | + LLCC (Last Level Cache Controller) provides last level of cache memory in SoC, + that can be shared by multiple clients. Clients here are different cores in the + SoC, the idea is to minimize the local caches at the clients and migrate to + common pool of memory. Cache memory is divided into partitions called slices + which are assigned to clients. Clients can query the slice details, activate + and deactivate them. + +properties: + compatible: + enum: + - qcom,sc7180-llcc + - qcom,sc7280-llcc + - qcom,sc8180x-llcc + - qcom,sc8280xp-llcc + - qcom,sdm845-llcc + - qcom,sm6350-llcc + - qcom,sm8150-llcc + - qcom,sm8250-llcc + - qcom,sm8350-llcc + - qcom,sm8450-llcc + - qcom,sm8550-llcc + + reg: + items: + - description: LLCC base register region + - description: LLCC broadcast base register region + + reg-names: + items: + - const: llcc_base + - const: llcc_broadcast_base + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +examples: + - | + #include + + system-cache-controller@1100000 { + compatible = "qcom,sdm845-llcc"; + reg = <0x1100000 0x200000>, <0x1300000 0x50000> ; + reg-names = "llcc_base", "llcc_broadcast_base"; + interrupts = ; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt new file mode 100644 index 000000000..c0e3c3a42 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt @@ -0,0 +1,58 @@ +SPM AVS Wrapper 2 (SAW2) + +The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the +Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable +power-controller that transitions a piece of hardware (like a processor or +subsystem) into and out of low power modes via a direct connection to +the PMIC. It can also be wired up to interact with other processors in the +system, notifying them when a low power state is entered or exited. + +Multiple revisions of the SAW hardware are supported using these Device Nodes. +SAW2 revisions differ in the register offset and configuration data. Also, the +same revision of the SAW in different SoCs may have different configuration +data due the differences in hardware capabilities. Hence the SoC name, the +version of the SAW hardware in that SoC and the distinction between cpu (big +or Little) or cache, may be needed to uniquely identify the SAW register +configuration and initialization data. The compatible string is used to +indicate this parameter. + +PROPERTIES + +- compatible: + Usage: required + Value type: + Definition: Must have + "qcom,saw2" + A more specific value could be one of: + "qcom,apq8064-saw2-v1.1-cpu" + "qcom,msm8226-saw2-v2.1-cpu" + "qcom,msm8974-saw2-v2.1-cpu" + "qcom,apq8084-saw2-v2.1-cpu" + +- reg: + Usage: required + Value type: + Definition: the first element specifies the base address and size of + the register region. An optional second element specifies + the base address and size of the alias register region. + +- regulator: + Usage: optional + Value type: boolean + Definition: Indicates that this SPM device acts as a regulator device + device for the core (CPU or Cache) the SPM is attached + to. + +Example 1: + + power-controller@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + +Example 2: + saw0: power-controller@f9089000 { + compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2"; + reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/ssbi.txt b/Documentation/devicetree/bindings/arm/msm/ssbi.txt new file mode 100644 index 000000000..54fd5ced3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/ssbi.txt @@ -0,0 +1,18 @@ +* Qualcomm SSBI + +Some Qualcomm MSM devices contain a point-to-point serial bus used to +communicate with a limited range of devices (mostly power management +chips). + +These require the following properties: + +- compatible: "qcom,ssbi" + +- qcom,controller-type + indicates the SSBI bus variant the controller should use to talk + with the slave device. This should be one of "ssbi", "ssbi2", or + "pmic-arbiter". The type chosen is determined by the attached + slave. + +The slave device should be the single child node of the ssbi device +with a compatible field. -- cgit v1.2.3