From 5b7c4cabbb65f5c469464da6c5f614cbd7f730f2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 21 Feb 2023 18:24:12 -0800 Subject: Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core: - Add dedicated kmem_cache for typical/small skb->head, avoid having to access struct page at kfree time, and improve memory use. - Introduce sysctl to set default RPS configuration for new netdevs. - Define Netlink protocol specification format which can be used to describe messages used by each family and auto-generate parsers. Add tools for generating kernel data structures and uAPI headers. - Expose all net/core sysctls inside netns. - Remove 4s sleep in netpoll if carrier is instantly detected on boot. - Add configurable limit of MDB entries per port, and port-vlan. - Continue populating drop reasons throughout the stack. - Retire a handful of legacy Qdiscs and classifiers. Protocols: - Support IPv4 big TCP (TSO frames larger than 64kB). - Add IP_LOCAL_PORT_RANGE socket option, to control local port range on socket by socket basis. - Track and report in procfs number of MPTCP sockets used. - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path manager. - IPv6: don't check net.ipv6.route.max_size and rely on garbage collection to free memory (similarly to IPv4). - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986). - ICMP: add per-rate limit counters. - Add support for user scanning requests in ieee802154. - Remove static WEP support. - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting. - WiFi 7 EHT channel puncturing support (client & AP). BPF: - Add a rbtree data structure following the "next-gen data structure" precedent set by recently added linked list, that is, by using kfunc + kptr instead of adding a new BPF map type. - Expose XDP hints via kfuncs with initial support for RX hash and timestamp metadata. - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to better support decap on GRE tunnel devices not operating in collect metadata. - Improve x86 JIT's codegen for PROBE_MEM runtime error checks. - Remove the need for trace_printk_lock for bpf_trace_printk and bpf_trace_vprintk helpers. - Extend libbpf's bpf_tracing.h support for tracing arguments of kprobes/uprobes and syscall as a special case. - Significantly reduce the search time for module symbols by livepatch and BPF. - Enable cpumasks to be used as kptrs, which is useful for tracing programs tracking which tasks end up running on which CPUs in different time intervals. - Add support for BPF trampoline on s390x and riscv64. - Add capability to export the XDP features supported by the NIC. - Add __bpf_kfunc tag for marking kernel functions as kfuncs. - Add cgroup.memory=nobpf kernel parameter option to disable BPF memory accounting for container environments. Netfilter: - Remove the CLUSTERIP target. It has been marked as obsolete for years, and we still have WARN splats wrt races of the out-of-band /proc interface installed by this target. - Add 'destroy' commands to nf_tables. They are identical to the existing 'delete' commands, but do not return an error if the referenced object (set, chain, rule...) did not exist. Driver API: - Improve cpumask_local_spread() locality to help NICs set the right IRQ affinity on AMD platforms. - Separate C22 and C45 MDIO bus transactions more clearly. - Introduce new DCB table to control DSCP rewrite on egress. - Support configuration of Physical Layer Collision Avoidance (PLCA) Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of shared medium Ethernet. - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing preemption of low priority frames by high priority frames. - Add support for controlling MACSec offload using netlink SET. - Rework devlink instance refcounts to allow registration and de-registration under the instance lock. Split the code into multiple files, drop some of the unnecessarily granular locks and factor out common parts of netlink operation handling. - Add TX frame aggregation parameters (for USB drivers). - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning messages with notifications for debug. - Allow offloading of UDP NEW connections via act_ct. - Add support for per action HW stats in TC. - Support hardware miss to TC action (continue processing in SW from a specific point in the action chain). - Warn if old Wireless Extension user space interface is used with modern cfg80211/mac80211 drivers. Do not support Wireless Extensions for Wi-Fi 7 devices at all. Everyone should switch to using nl80211 interface instead. - Improve the CAN bit timing configuration. Use extack to return error messages directly to user space, update the SJW handling, including the definition of a new default value that will benefit CAN-FD controllers, by increasing their oscillator tolerance. New hardware / drivers: - Ethernet: - nVidia BlueField-3 support (control traffic driver) - Ethernet support for imx93 SoCs - Motorcomm yt8531 gigabit Ethernet PHY - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA) - Microchip LAN8841 PHY (incl. cable diagnostics and PTP) - Amlogic gxl MDIO mux - WiFi: - RealTek RTL8188EU (rtl8xxxu) - Qualcomm Wi-Fi 7 devices (ath12k) - CAN: - Renesas R-Car V4H Drivers: - Bluetooth: - Set Per Platform Antenna Gain (PPAG) for Intel controllers. - Ethernet NICs: - Intel (1G, igc): - support TSN / Qbv / packet scheduling features of i226 model - Intel (100G, ice): - use GNSS subsystem instead of TTY - multi-buffer XDP support - extend support for GPIO pins to E823 devices - nVidia/Mellanox: - update the shared buffer configuration on PFC commands - implement PTP adjphase function for HW offset control - TC support for Geneve and GRE with VF tunnel offload - more efficient crypto key management method - multi-port eswitch support - Netronome/Corigine: - add DCB IEEE support - support IPsec offloading for NFP3800 - Freescale/NXP (enetc): - support XDP_REDIRECT for XDP non-linear buffers - improve reconfig, avoid link flap and waiting for idle - support MAC Merge layer - Other NICs: - sfc/ef100: add basic devlink support for ef100 - ionic: rx_push mode operation (writing descriptors via MMIO) - bnxt: use the auxiliary bus abstraction for RDMA - r8169: disable ASPM and reset bus in case of tx timeout - cpsw: support QSGMII mode for J721e CPSW9G - cpts: support pulse-per-second output - ngbe: add an mdio bus driver - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing - r8152: handle devices with FW with NCM support - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation - virtio-net: support multi buffer XDP - virtio/vsock: replace virtio_vsock_pkt with sk_buff - tsnep: XDP support - Ethernet high-speed switches: - nVidia/Mellanox (mlxsw): - add support for latency TLV (in FW control messages) - Microchip (sparx5): - separate explicit and implicit traffic forwarding rules, make the implicit rules always active - add support for egress DSCP rewrite - IS0 VCAP support (Ingress Classification) - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.) - ES2 VCAP support (Egress Access Control) - support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1) - Ethernet embedded switches: - Marvell (mv88e6xxx): - add MAB (port auth) offload support - enable PTP receive for mv88e6390 - NXP (ocelot): - support MAC Merge layer - support for the the vsc7512 internal copper phys - Microchip: - lan9303: convert to PHYLINK - lan966x: support TC flower filter statistics - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x - lan937x: support Credit Based Shaper configuration - ksz9477: support Energy Efficient Ethernet - other: - qca8k: convert to regmap read/write API, use bulk operations - rswitch: Improve TX timestamp accuracy - Intel WiFi (iwlwifi): - EHT (Wi-Fi 7) rate reporting - STEP equalizer support: transfer some STEP (connection to radio on platforms with integrated wifi) related parameters from the BIOS to the firmware. - Qualcomm 802.11ax WiFi (ath11k): - IPQ5018 support - Fine Timing Measurement (FTM) responder role support - channel 177 support - MediaTek WiFi (mt76): - per-PHY LED support - mt7996: EHT (Wi-Fi 7) support - Wireless Ethernet Dispatch (WED) reset support - switch to using page pool allocator - RealTek WiFi (rtw89): - support new version of Bluetooth co-existance - Mobile: - rmnet: support TX aggregation" * tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits) page_pool: add a comment explaining the fragment counter usage net: ethtool: fix __ethtool_dev_mm_supported() implementation ethtool: pse-pd: Fix double word in comments xsk: add linux/vmalloc.h to xsk.c sefltests: netdevsim: wait for devlink instance after netns removal selftest: fib_tests: Always cleanup before exit net/mlx5e: Align IPsec ASO result memory to be as required by hardware net/mlx5e: TC, Set CT miss to the specific ct action instance net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG net/mlx5: Refactor tc miss handling to a single function net/mlx5: Kconfig: Make tc offload depend on tc skb extension net/sched: flower: Support hardware miss to tc action net/sched: flower: Move filter handle initialization earlier net/sched: cls_api: Support hardware miss to tc action net/sched: Rename user cookie and act cookie sfc: fix builds without CONFIG_RTC_LIB sfc: clean up some inconsistent indentings net/mlx4_en: Introduce flexible array to silence overflow warning net: lan966x: Fix possible deadlock inside PTP net/ulp: Remove redundant ->clone() test in inet_clone_ulp(). ... --- drivers/regulator/ab8500-ext.c | 473 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 473 insertions(+) create mode 100644 drivers/regulator/ab8500-ext.c (limited to 'drivers/regulator/ab8500-ext.c') diff --git a/drivers/regulator/ab8500-ext.c b/drivers/regulator/ab8500-ext.c new file mode 100644 index 000000000..4f26952ca --- /dev/null +++ b/drivers/regulator/ab8500-ext.c @@ -0,0 +1,473 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) ST-Ericsson SA 2010 + * + * Authors: Bengt Jonsson + * + * This file is based on drivers/regulator/ab8500.c + * + * AB8500 external regulators + * + * ab8500-ext supports the following regulators: + * - VextSupply3 + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* AB8500 external regulators */ +enum ab8500_ext_regulator_id { + AB8500_EXT_SUPPLY1, + AB8500_EXT_SUPPLY2, + AB8500_EXT_SUPPLY3, + AB8500_NUM_EXT_REGULATORS, +}; + +struct ab8500_ext_regulator_cfg { + bool hwreq; /* requires hw mode or high power mode */ +}; + +/* supply for VextSupply3 */ +static struct regulator_consumer_supply ab8500_ext_supply3_consumers[] = { + /* SIM supply for 3 V SIM cards */ + REGULATOR_SUPPLY("vinvsim", "sim-detect.0"), +}; + +/* + * AB8500 external regulators + */ +static struct regulator_init_data ab8500_ext_regulators[] = { + /* fixed Vbat supplies VSMPS1_EXT_1V8 */ + [AB8500_EXT_SUPPLY1] = { + .constraints = { + .name = "ab8500-ext-supply1", + .min_uV = 1800000, + .max_uV = 1800000, + .initial_mode = REGULATOR_MODE_IDLE, + .boot_on = 1, + .always_on = 1, + }, + }, + /* fixed Vbat supplies VSMPS2_EXT_1V36 and VSMPS5_EXT_1V15 */ + [AB8500_EXT_SUPPLY2] = { + .constraints = { + .name = "ab8500-ext-supply2", + .min_uV = 1360000, + .max_uV = 1360000, + }, + }, + /* fixed Vbat supplies VSMPS3_EXT_3V4 and VSMPS4_EXT_3V4 */ + [AB8500_EXT_SUPPLY3] = { + .constraints = { + .name = "ab8500-ext-supply3", + .min_uV = 3400000, + .max_uV = 3400000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = + ARRAY_SIZE(ab8500_ext_supply3_consumers), + .consumer_supplies = ab8500_ext_supply3_consumers, + }, +}; + +/** + * struct ab8500_ext_regulator_info - ab8500 regulator information + * @dev: device pointer + * @desc: regulator description + * @cfg: regulator configuration (extension of regulator FW configuration) + * @update_bank: bank to control on/off + * @update_reg: register to control on/off + * @update_mask: mask to enable/disable and set mode of regulator + * @update_val: bits holding the regulator current mode + * @update_val_hp: bits to set EN pin active (LPn pin deactive) + * normally this means high power mode + * @update_val_lp: bits to set EN pin active and LPn pin active + * normally this means low power mode + * @update_val_hw: bits to set regulator pins in HW control + * SysClkReq pins and logic will choose mode + */ +struct ab8500_ext_regulator_info { + struct device *dev; + struct regulator_desc desc; + struct ab8500_ext_regulator_cfg *cfg; + u8 update_bank; + u8 update_reg; + u8 update_mask; + u8 update_val; + u8 update_val_hp; + u8 update_val_lp; + u8 update_val_hw; +}; + +static int ab8500_ext_regulator_enable(struct regulator_dev *rdev) +{ + int ret; + struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev); + u8 regval; + + if (info == NULL) { + dev_err(rdev_get_dev(rdev), "regulator info null pointer\n"); + return -EINVAL; + } + + /* + * To satisfy both HW high power request and SW request, the regulator + * must be on in high power. + */ + if (info->cfg && info->cfg->hwreq) + regval = info->update_val_hp; + else + regval = info->update_val; + + ret = abx500_mask_and_set_register_interruptible(info->dev, + info->update_bank, info->update_reg, + info->update_mask, regval); + if (ret < 0) { + dev_err(rdev_get_dev(rdev), + "couldn't set enable bits for regulator\n"); + return ret; + } + + dev_dbg(rdev_get_dev(rdev), + "%s-enable (bank, reg, mask, value): 0x%02x, 0x%02x, 0x%02x, 0x%02x\n", + info->desc.name, info->update_bank, info->update_reg, + info->update_mask, regval); + + return 0; +} + +static int ab8500_ext_regulator_disable(struct regulator_dev *rdev) +{ + int ret; + struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev); + u8 regval; + + if (info == NULL) { + dev_err(rdev_get_dev(rdev), "regulator info null pointer\n"); + return -EINVAL; + } + + /* + * Set the regulator in HW request mode if configured + */ + if (info->cfg && info->cfg->hwreq) + regval = info->update_val_hw; + else + regval = 0; + + ret = abx500_mask_and_set_register_interruptible(info->dev, + info->update_bank, info->update_reg, + info->update_mask, regval); + if (ret < 0) { + dev_err(rdev_get_dev(rdev), + "couldn't set disable bits for regulator\n"); + return ret; + } + + dev_dbg(rdev_get_dev(rdev), "%s-disable (bank, reg, mask, value):" + " 0x%02x, 0x%02x, 0x%02x, 0x%02x\n", + info->desc.name, info->update_bank, info->update_reg, + info->update_mask, regval); + + return 0; +} + +static int ab8500_ext_regulator_is_enabled(struct regulator_dev *rdev) +{ + int ret; + struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev); + u8 regval; + + if (info == NULL) { + dev_err(rdev_get_dev(rdev), "regulator info null pointer\n"); + return -EINVAL; + } + + ret = abx500_get_register_interruptible(info->dev, + info->update_bank, info->update_reg, ®val); + if (ret < 0) { + dev_err(rdev_get_dev(rdev), + "couldn't read 0x%x register\n", info->update_reg); + return ret; + } + + dev_dbg(rdev_get_dev(rdev), "%s-is_enabled (bank, reg, mask, value):" + " 0x%02x, 0x%02x, 0x%02x, 0x%02x\n", + info->desc.name, info->update_bank, info->update_reg, + info->update_mask, regval); + + if (((regval & info->update_mask) == info->update_val_lp) || + ((regval & info->update_mask) == info->update_val_hp)) + return 1; + else + return 0; +} + +static int ab8500_ext_regulator_set_mode(struct regulator_dev *rdev, + unsigned int mode) +{ + int ret = 0; + struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev); + u8 regval; + + if (info == NULL) { + dev_err(rdev_get_dev(rdev), "regulator info null pointer\n"); + return -EINVAL; + } + + switch (mode) { + case REGULATOR_MODE_NORMAL: + regval = info->update_val_hp; + break; + case REGULATOR_MODE_IDLE: + regval = info->update_val_lp; + break; + + default: + return -EINVAL; + } + + /* If regulator is enabled and info->cfg->hwreq is set, the regulator + must be on in high power, so we don't need to write the register with + the same value. + */ + if (ab8500_ext_regulator_is_enabled(rdev) && + !(info->cfg && info->cfg->hwreq)) { + ret = abx500_mask_and_set_register_interruptible(info->dev, + info->update_bank, info->update_reg, + info->update_mask, regval); + if (ret < 0) { + dev_err(rdev_get_dev(rdev), + "Could not set regulator mode.\n"); + return ret; + } + + dev_dbg(rdev_get_dev(rdev), + "%s-set_mode (bank, reg, mask, value): " + "0x%x, 0x%x, 0x%x, 0x%x\n", + info->desc.name, info->update_bank, info->update_reg, + info->update_mask, regval); + } + + info->update_val = regval; + + return 0; +} + +static unsigned int ab8500_ext_regulator_get_mode(struct regulator_dev *rdev) +{ + struct ab8500_ext_regulator_info *info = rdev_get_drvdata(rdev); + int ret; + + if (info == NULL) { + dev_err(rdev_get_dev(rdev), "regulator info null pointer\n"); + return -EINVAL; + } + + if (info->update_val == info->update_val_hp) + ret = REGULATOR_MODE_NORMAL; + else if (info->update_val == info->update_val_lp) + ret = REGULATOR_MODE_IDLE; + else + ret = -EINVAL; + + return ret; +} + +static int ab8500_ext_set_voltage(struct regulator_dev *rdev, int min_uV, + int max_uV, unsigned *selector) +{ + struct regulation_constraints *regu_constraints = rdev->constraints; + + if (!regu_constraints) { + dev_err(rdev_get_dev(rdev), "No regulator constraints\n"); + return -EINVAL; + } + + if (regu_constraints->min_uV == min_uV && + regu_constraints->max_uV == max_uV) + return 0; + + dev_err(rdev_get_dev(rdev), + "Requested min %duV max %duV != constrained min %duV max %duV\n", + min_uV, max_uV, + regu_constraints->min_uV, regu_constraints->max_uV); + + return -EINVAL; +} + +static int ab8500_ext_list_voltage(struct regulator_dev *rdev, + unsigned selector) +{ + struct regulation_constraints *regu_constraints = rdev->constraints; + + if (regu_constraints == NULL) { + dev_err(rdev_get_dev(rdev), "regulator constraints null pointer\n"); + return -EINVAL; + } + /* return the uV for the fixed regulators */ + if (regu_constraints->min_uV && regu_constraints->max_uV) { + if (regu_constraints->min_uV == regu_constraints->max_uV) + return regu_constraints->min_uV; + } + return -EINVAL; +} + +static const struct regulator_ops ab8500_ext_regulator_ops = { + .enable = ab8500_ext_regulator_enable, + .disable = ab8500_ext_regulator_disable, + .is_enabled = ab8500_ext_regulator_is_enabled, + .set_mode = ab8500_ext_regulator_set_mode, + .get_mode = ab8500_ext_regulator_get_mode, + .set_voltage = ab8500_ext_set_voltage, + .list_voltage = ab8500_ext_list_voltage, +}; + +static struct ab8500_ext_regulator_info + ab8500_ext_regulator_info[AB8500_NUM_EXT_REGULATORS] = { + [AB8500_EXT_SUPPLY1] = { + .desc = { + .name = "VEXTSUPPLY1", + .of_match = of_match_ptr("ab8500_ext1"), + .ops = &ab8500_ext_regulator_ops, + .type = REGULATOR_VOLTAGE, + .id = AB8500_EXT_SUPPLY1, + .owner = THIS_MODULE, + .n_voltages = 1, + }, + .update_bank = 0x04, + .update_reg = 0x08, + .update_mask = 0x03, + .update_val = 0x01, + .update_val_hp = 0x01, + .update_val_lp = 0x03, + .update_val_hw = 0x02, + }, + [AB8500_EXT_SUPPLY2] = { + .desc = { + .name = "VEXTSUPPLY2", + .of_match = of_match_ptr("ab8500_ext2"), + .ops = &ab8500_ext_regulator_ops, + .type = REGULATOR_VOLTAGE, + .id = AB8500_EXT_SUPPLY2, + .owner = THIS_MODULE, + .n_voltages = 1, + }, + .update_bank = 0x04, + .update_reg = 0x08, + .update_mask = 0x0c, + .update_val = 0x04, + .update_val_hp = 0x04, + .update_val_lp = 0x0c, + .update_val_hw = 0x08, + }, + [AB8500_EXT_SUPPLY3] = { + .desc = { + .name = "VEXTSUPPLY3", + .of_match = of_match_ptr("ab8500_ext3"), + .ops = &ab8500_ext_regulator_ops, + .type = REGULATOR_VOLTAGE, + .id = AB8500_EXT_SUPPLY3, + .owner = THIS_MODULE, + .n_voltages = 1, + }, + .update_bank = 0x04, + .update_reg = 0x08, + .update_mask = 0x30, + .update_val = 0x10, + .update_val_hp = 0x10, + .update_val_lp = 0x30, + .update_val_hw = 0x20, + }, +}; + +static int ab8500_ext_regulator_probe(struct platform_device *pdev) +{ + struct ab8500 *ab8500 = dev_get_drvdata(pdev->dev.parent); + struct regulator_config config = { }; + struct regulator_dev *rdev; + int i; + + if (!ab8500) { + dev_err(&pdev->dev, "null mfd parent\n"); + return -EINVAL; + } + + /* check for AB8500 2.x */ + if (is_ab8500_2p0_or_earlier(ab8500)) { + struct ab8500_ext_regulator_info *info; + + /* VextSupply3LPn is inverted on AB8500 2.x */ + info = &ab8500_ext_regulator_info[AB8500_EXT_SUPPLY3]; + info->update_val = 0x30; + info->update_val_hp = 0x30; + info->update_val_lp = 0x10; + } + + /* register all regulators */ + for (i = 0; i < ARRAY_SIZE(ab8500_ext_regulator_info); i++) { + struct ab8500_ext_regulator_info *info = NULL; + + /* assign per-regulator data */ + info = &ab8500_ext_regulator_info[i]; + info->dev = &pdev->dev; + info->cfg = (struct ab8500_ext_regulator_cfg *) + ab8500_ext_regulators[i].driver_data; + + config.dev = &pdev->dev; + config.driver_data = info; + config.init_data = &ab8500_ext_regulators[i]; + + /* register regulator with framework */ + rdev = devm_regulator_register(&pdev->dev, &info->desc, + &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "failed to register regulator %s\n", + info->desc.name); + return PTR_ERR(rdev); + } + + dev_dbg(&pdev->dev, "%s-probed\n", info->desc.name); + } + + return 0; +} + +static struct platform_driver ab8500_ext_regulator_driver = { + .probe = ab8500_ext_regulator_probe, + .driver = { + .name = "ab8500-ext-regulator", + }, +}; + +static int __init ab8500_ext_regulator_init(void) +{ + int ret; + + ret = platform_driver_register(&ab8500_ext_regulator_driver); + if (ret) + pr_err("Failed to register ab8500 ext regulator: %d\n", ret); + + return ret; +} +subsys_initcall(ab8500_ext_regulator_init); + +static void __exit ab8500_ext_regulator_exit(void) +{ + platform_driver_unregister(&ab8500_ext_regulator_driver); +} +module_exit(ab8500_ext_regulator_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Bengt Jonsson "); +MODULE_DESCRIPTION("AB8500 external regulator driver"); +MODULE_ALIAS("platform:ab8500-ext-regulator"); -- cgit v1.2.3