From 5b7c4cabbb65f5c469464da6c5f614cbd7f730f2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 21 Feb 2023 18:24:12 -0800 Subject: Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core: - Add dedicated kmem_cache for typical/small skb->head, avoid having to access struct page at kfree time, and improve memory use. - Introduce sysctl to set default RPS configuration for new netdevs. - Define Netlink protocol specification format which can be used to describe messages used by each family and auto-generate parsers. Add tools for generating kernel data structures and uAPI headers. - Expose all net/core sysctls inside netns. - Remove 4s sleep in netpoll if carrier is instantly detected on boot. - Add configurable limit of MDB entries per port, and port-vlan. - Continue populating drop reasons throughout the stack. - Retire a handful of legacy Qdiscs and classifiers. Protocols: - Support IPv4 big TCP (TSO frames larger than 64kB). - Add IP_LOCAL_PORT_RANGE socket option, to control local port range on socket by socket basis. - Track and report in procfs number of MPTCP sockets used. - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path manager. - IPv6: don't check net.ipv6.route.max_size and rely on garbage collection to free memory (similarly to IPv4). - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986). - ICMP: add per-rate limit counters. - Add support for user scanning requests in ieee802154. - Remove static WEP support. - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting. - WiFi 7 EHT channel puncturing support (client & AP). BPF: - Add a rbtree data structure following the "next-gen data structure" precedent set by recently added linked list, that is, by using kfunc + kptr instead of adding a new BPF map type. - Expose XDP hints via kfuncs with initial support for RX hash and timestamp metadata. - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to better support decap on GRE tunnel devices not operating in collect metadata. - Improve x86 JIT's codegen for PROBE_MEM runtime error checks. - Remove the need for trace_printk_lock for bpf_trace_printk and bpf_trace_vprintk helpers. - Extend libbpf's bpf_tracing.h support for tracing arguments of kprobes/uprobes and syscall as a special case. - Significantly reduce the search time for module symbols by livepatch and BPF. - Enable cpumasks to be used as kptrs, which is useful for tracing programs tracking which tasks end up running on which CPUs in different time intervals. - Add support for BPF trampoline on s390x and riscv64. - Add capability to export the XDP features supported by the NIC. - Add __bpf_kfunc tag for marking kernel functions as kfuncs. - Add cgroup.memory=nobpf kernel parameter option to disable BPF memory accounting for container environments. Netfilter: - Remove the CLUSTERIP target. It has been marked as obsolete for years, and we still have WARN splats wrt races of the out-of-band /proc interface installed by this target. - Add 'destroy' commands to nf_tables. They are identical to the existing 'delete' commands, but do not return an error if the referenced object (set, chain, rule...) did not exist. Driver API: - Improve cpumask_local_spread() locality to help NICs set the right IRQ affinity on AMD platforms. - Separate C22 and C45 MDIO bus transactions more clearly. - Introduce new DCB table to control DSCP rewrite on egress. - Support configuration of Physical Layer Collision Avoidance (PLCA) Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of shared medium Ethernet. - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing preemption of low priority frames by high priority frames. - Add support for controlling MACSec offload using netlink SET. - Rework devlink instance refcounts to allow registration and de-registration under the instance lock. Split the code into multiple files, drop some of the unnecessarily granular locks and factor out common parts of netlink operation handling. - Add TX frame aggregation parameters (for USB drivers). - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning messages with notifications for debug. - Allow offloading of UDP NEW connections via act_ct. - Add support for per action HW stats in TC. - Support hardware miss to TC action (continue processing in SW from a specific point in the action chain). - Warn if old Wireless Extension user space interface is used with modern cfg80211/mac80211 drivers. Do not support Wireless Extensions for Wi-Fi 7 devices at all. Everyone should switch to using nl80211 interface instead. - Improve the CAN bit timing configuration. Use extack to return error messages directly to user space, update the SJW handling, including the definition of a new default value that will benefit CAN-FD controllers, by increasing their oscillator tolerance. New hardware / drivers: - Ethernet: - nVidia BlueField-3 support (control traffic driver) - Ethernet support for imx93 SoCs - Motorcomm yt8531 gigabit Ethernet PHY - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA) - Microchip LAN8841 PHY (incl. cable diagnostics and PTP) - Amlogic gxl MDIO mux - WiFi: - RealTek RTL8188EU (rtl8xxxu) - Qualcomm Wi-Fi 7 devices (ath12k) - CAN: - Renesas R-Car V4H Drivers: - Bluetooth: - Set Per Platform Antenna Gain (PPAG) for Intel controllers. - Ethernet NICs: - Intel (1G, igc): - support TSN / Qbv / packet scheduling features of i226 model - Intel (100G, ice): - use GNSS subsystem instead of TTY - multi-buffer XDP support - extend support for GPIO pins to E823 devices - nVidia/Mellanox: - update the shared buffer configuration on PFC commands - implement PTP adjphase function for HW offset control - TC support for Geneve and GRE with VF tunnel offload - more efficient crypto key management method - multi-port eswitch support - Netronome/Corigine: - add DCB IEEE support - support IPsec offloading for NFP3800 - Freescale/NXP (enetc): - support XDP_REDIRECT for XDP non-linear buffers - improve reconfig, avoid link flap and waiting for idle - support MAC Merge layer - Other NICs: - sfc/ef100: add basic devlink support for ef100 - ionic: rx_push mode operation (writing descriptors via MMIO) - bnxt: use the auxiliary bus abstraction for RDMA - r8169: disable ASPM and reset bus in case of tx timeout - cpsw: support QSGMII mode for J721e CPSW9G - cpts: support pulse-per-second output - ngbe: add an mdio bus driver - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing - r8152: handle devices with FW with NCM support - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation - virtio-net: support multi buffer XDP - virtio/vsock: replace virtio_vsock_pkt with sk_buff - tsnep: XDP support - Ethernet high-speed switches: - nVidia/Mellanox (mlxsw): - add support for latency TLV (in FW control messages) - Microchip (sparx5): - separate explicit and implicit traffic forwarding rules, make the implicit rules always active - add support for egress DSCP rewrite - IS0 VCAP support (Ingress Classification) - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.) - ES2 VCAP support (Egress Access Control) - support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1) - Ethernet embedded switches: - Marvell (mv88e6xxx): - add MAB (port auth) offload support - enable PTP receive for mv88e6390 - NXP (ocelot): - support MAC Merge layer - support for the the vsc7512 internal copper phys - Microchip: - lan9303: convert to PHYLINK - lan966x: support TC flower filter statistics - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x - lan937x: support Credit Based Shaper configuration - ksz9477: support Energy Efficient Ethernet - other: - qca8k: convert to regmap read/write API, use bulk operations - rswitch: Improve TX timestamp accuracy - Intel WiFi (iwlwifi): - EHT (Wi-Fi 7) rate reporting - STEP equalizer support: transfer some STEP (connection to radio on platforms with integrated wifi) related parameters from the BIOS to the firmware. - Qualcomm 802.11ax WiFi (ath11k): - IPQ5018 support - Fine Timing Measurement (FTM) responder role support - channel 177 support - MediaTek WiFi (mt76): - per-PHY LED support - mt7996: EHT (Wi-Fi 7) support - Wireless Ethernet Dispatch (WED) reset support - switch to using page pool allocator - RealTek WiFi (rtw89): - support new version of Bluetooth co-existance - Mobile: - rmnet: support TX aggregation" * tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits) page_pool: add a comment explaining the fragment counter usage net: ethtool: fix __ethtool_dev_mm_supported() implementation ethtool: pse-pd: Fix double word in comments xsk: add linux/vmalloc.h to xsk.c sefltests: netdevsim: wait for devlink instance after netns removal selftest: fib_tests: Always cleanup before exit net/mlx5e: Align IPsec ASO result memory to be as required by hardware net/mlx5e: TC, Set CT miss to the specific ct action instance net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG net/mlx5: Refactor tc miss handling to a single function net/mlx5: Kconfig: Make tc offload depend on tc skb extension net/sched: flower: Support hardware miss to tc action net/sched: flower: Move filter handle initialization earlier net/sched: cls_api: Support hardware miss to tc action net/sched: Rename user cookie and act cookie sfc: fix builds without CONFIG_RTC_LIB sfc: clean up some inconsistent indentings net/mlx4_en: Introduce flexible array to silence overflow warning net: lan966x: Fix possible deadlock inside PTP net/ulp: Remove redundant ->clone() test in inet_clone_ulp(). ... --- drivers/tty/Kconfig | 404 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 404 insertions(+) create mode 100644 drivers/tty/Kconfig (limited to 'drivers/tty/Kconfig') diff --git a/drivers/tty/Kconfig b/drivers/tty/Kconfig new file mode 100644 index 000000000..d35fc068d --- /dev/null +++ b/drivers/tty/Kconfig @@ -0,0 +1,404 @@ +# SPDX-License-Identifier: GPL-2.0 +config TTY + bool "Enable TTY" if EXPERT + default y + help + Allows you to remove TTY support which can save space, and + blocks features that require TTY from inclusion in the kernel. + TTY is required for any text terminals or serial port + communication. Most users should leave this enabled. + +if TTY + +config VT + bool "Virtual terminal" if EXPERT + select INPUT + default y if !UML + help + If you say Y here, you will get support for terminal devices with + display and keyboard devices. These are called "virtual" because you + can run several virtual terminals (also called virtual consoles) on + one physical terminal. This is rather useful, for example one + virtual terminal can collect system messages and warnings, another + one can be used for a text-mode user session, and a third could run + an X session, all in parallel. Switching between virtual terminals + is done with certain key combinations, usually Alt-. + + The setterm command ("man setterm") can be used to change the + properties (such as colors or beeping) of a virtual terminal. The + man page console_codes(4) ("man console_codes") contains the special + character sequences that can be used to change those properties + directly. The fonts used on virtual terminals can be changed with + the setfont ("man setfont") command and the key bindings are defined + with the loadkeys ("man loadkeys") command. + + You need at least one virtual terminal device in order to make use + of your keyboard and monitor. Therefore, only people configuring an + embedded system would want to say N here in order to save some + memory; the only way to log into such a system is then via a serial + or network connection. + + If unsure, say Y, or else you won't be able to do much with your new + shiny Linux system :-) + +config CONSOLE_TRANSLATIONS + depends on VT + default y + bool "Enable character translations in console" if EXPERT + help + This enables support for font mapping and Unicode translation + on virtual consoles. + +config VT_CONSOLE + bool "Support for console on virtual terminal" if EXPERT + depends on VT + default y + help + The system console is the device which receives all kernel messages + and warnings and which allows logins in single user mode. If you + answer Y here, a virtual terminal (the device used to interact with + a physical terminal) can be used as system console. This is the most + common mode of operations, so you should say Y here unless you want + the kernel messages be output only to a serial port (in which case + you should say Y to "Console on serial port", below). + + If you do say Y here, by default the currently visible virtual + terminal (/dev/tty0) will be used as system console. You can change + that with a kernel command line option such as "console=tty3" which + would use the third virtual terminal as system console. (Try "man + bootparam" or see the documentation of your boot loader (lilo or + loadlin) about how to pass options to the kernel at boot time.) + + If unsure, say Y. + +config VT_CONSOLE_SLEEP + def_bool y + depends on VT_CONSOLE && PM_SLEEP + +config HW_CONSOLE + bool + depends on VT + default y + +config VT_HW_CONSOLE_BINDING + bool "Support for binding and unbinding console drivers" + depends on HW_CONSOLE + help + The virtual terminal is the device that interacts with the physical + terminal through console drivers. On these systems, at least one + console driver is loaded. In other configurations, additional console + drivers may be enabled, such as the framebuffer console. If more than + 1 console driver is enabled, setting this to 'y' will allow you to + select the console driver that will serve as the backend for the + virtual terminals. + + See for more + information. For framebuffer console users, please refer to + . + +config UNIX98_PTYS + bool "Unix98 PTY support" if EXPERT + default y + help + A pseudo terminal (PTY) is a software device consisting of two + halves: a master and a slave. The slave device behaves identical to + a physical terminal; the master device is used by a process to + read data from and write data to the slave, thereby emulating a + terminal. Typical programs for the master side are telnet servers + and xterms. + + Linux has traditionally used the BSD-like names /dev/ptyxx for + masters and /dev/ttyxx for slaves of pseudo terminals. This scheme + has a number of problems. The GNU C library glibc 2.1 and later, + however, supports the Unix98 naming standard: in order to acquire a + pseudo terminal, a process opens /dev/ptmx; the number of the pseudo + terminal is then made available to the process and the pseudo + terminal slave can be accessed as /dev/pts/. What was + traditionally /dev/ttyp2 will then be /dev/pts/2, for example. + + All modern Linux systems use the Unix98 ptys. Say Y unless + you're on an embedded system and want to conserve memory. + +config LEGACY_PTYS + bool "Legacy (BSD) PTY support" + default y + help + A pseudo terminal (PTY) is a software device consisting of two + halves: a master and a slave. The slave device behaves identical to + a physical terminal; the master device is used by a process to + read data from and write data to the slave, thereby emulating a + terminal. Typical programs for the master side are telnet servers + and xterms. + + Linux has traditionally used the BSD-like names /dev/ptyxx + for masters and /dev/ttyxx for slaves of pseudo + terminals. This scheme has a number of problems, including + security. This option enables these legacy devices; on most + systems, it is safe to say N. + +config LEGACY_PTY_COUNT + int "Maximum number of legacy PTY in use" + depends on LEGACY_PTYS + range 0 256 + default "256" + help + The maximum number of legacy PTYs that can be used at any one time. + The default is 256, and should be more than enough. Embedded + systems may want to reduce this to save memory. + + When not in use, each legacy PTY occupies 12 bytes on 32-bit + architectures and 24 bytes on 64-bit architectures. + +config LEGACY_TIOCSTI + bool "Allow legacy TIOCSTI usage" + default y + help + Historically the kernel has allowed TIOCSTI, which will push + characters into a controlling TTY. This continues to be used + as a malicious privilege escalation mechanism, and provides no + meaningful real-world utility any more. Its use is considered + a dangerous legacy operation, and can be disabled on most + systems. + + Say 'Y here only if you have confirmed that your system's + userspace depends on this functionality to continue operating + normally. + + This functionality can be changed at runtime with the + dev.tty.legacy_tiocsti sysctl. This configuration option sets + the default value of the sysctl. + +config LDISC_AUTOLOAD + bool "Automatically load TTY Line Disciplines" + default y + help + Historically the kernel has always automatically loaded any + line discipline that is in a kernel module when a user asks + for it to be loaded with the TIOCSETD ioctl, or through other + means. This is not always the best thing to do on systems + where you know you will not be using some of the more + "ancient" line disciplines, so prevent the kernel from doing + this unless the request is coming from a process with the + CAP_SYS_MODULE permissions. + + Say 'Y' here if you trust your userspace users to do the right + thing, or if you have only provided the line disciplines that + you know you will be using, or if you wish to continue to use + the traditional method of on-demand loading of these modules + by any user. + + This functionality can be changed at runtime with the + dev.tty.ldisc_autoload sysctl, this configuration option will + only set the default value of this functionality. + +source "drivers/tty/serial/Kconfig" + +config SERIAL_NONSTANDARD + bool "Non-standard serial port support" + depends on HAS_IOMEM + help + Say Y here if you have any non-standard serial boards -- boards + which aren't supported using the standard "dumb" serial driver. + This includes intelligent serial boards such as + Digiboards, etc. These are usually used for systems that need many + serial ports because they serve many terminals or dial-in + connections. + + Note that the answer to this question won't directly affect the + kernel: saying N will just cause the configurator to skip all + the questions about non-standard serial boards. + + Most people can say N here. + +config MOXA_INTELLIO + tristate "Moxa Intellio support" + depends on SERIAL_NONSTANDARD && (ISA || EISA || PCI) + select FW_LOADER + help + Say Y here if you have a Moxa Intellio multiport serial card. + + To compile this driver as a module, choose M here: the + module will be called moxa. + +config MOXA_SMARTIO + tristate "Moxa SmartIO support v. 2.0" + depends on SERIAL_NONSTANDARD && PCI + help + Say Y here if you have a Moxa SmartIO multiport serial card and/or + want to help develop a new version of this driver. + + This is upgraded (1.9.1) driver from original Moxa drivers with + changes finally resulting in PCI probing. + + This driver can also be built as a module. The module will be called + mxser. If you want to do that, say M here. + +config SYNCLINK_GT + tristate "SyncLink GT/AC support" + depends on SERIAL_NONSTANDARD && PCI + help + Support for SyncLink GT and SyncLink AC families of + synchronous and asynchronous serial adapters + manufactured by Microgate Systems, Ltd. (www.microgate.com) + +config N_HDLC + tristate "HDLC line discipline support" + depends on SERIAL_NONSTANDARD + help + Allows synchronous HDLC communications with tty device drivers that + support synchronous HDLC such as the Microgate SyncLink adapter. + + This driver can be built as a module ( = code which can be + inserted in and removed from the running kernel whenever you want). + The module will be called n_hdlc. If you want to do that, say M + here. + +config PPC_EPAPR_HV_BYTECHAN + bool "ePAPR hypervisor byte channel driver" + depends on PPC + select EPAPR_PARAVIRT + help + This driver creates /dev entries for each ePAPR hypervisor byte + channel, thereby allowing applications to communicate with byte + channels as if they were serial ports. + +config PPC_EARLY_DEBUG_EHV_BC + bool "Early console (udbg) support for ePAPR hypervisors" + depends on PPC_EPAPR_HV_BYTECHAN=y + help + Select this option to enable early console (a.k.a. "udbg") support + via an ePAPR byte channel. You also need to choose the byte channel + handle below. + +config PPC_EARLY_DEBUG_EHV_BC_HANDLE + int "Byte channel handle for early console (udbg)" + depends on PPC_EARLY_DEBUG_EHV_BC + default 0 + help + If you want early console (udbg) output through a byte channel, + specify the handle of the byte channel to use. + + For this to work, the byte channel driver must be compiled + in-kernel, not as a module. + + Note that only one early console driver can be enabled, so don't + enable any others if you enable this one. + + If the number you specify is not a valid byte channel handle, then + there simply will be no early console output. This is true also + if you don't boot under a hypervisor at all. + +config GOLDFISH_TTY + tristate "Goldfish TTY Driver" + depends on GOLDFISH + select SERIAL_CORE + select SERIAL_CORE_CONSOLE + help + Console and system TTY driver for the Goldfish virtual platform. + +config GOLDFISH_TTY_EARLY_CONSOLE + bool + default y if GOLDFISH_TTY=y + select SERIAL_EARLYCON + +config N_GSM + tristate "GSM MUX line discipline support (EXPERIMENTAL)" + depends on NET + help + This line discipline provides support for the GSM MUX protocol and + presents the mux as a set of 61 individual tty devices. + +config NOZOMI + tristate "HSDPA Broadband Wireless Data Card - Globe Trotter" + depends on PCI + help + If you have a HSDPA driver Broadband Wireless Data Card - + Globe Trotter PCMCIA card, say Y here. + + To compile this driver as a module, choose M here, the module + will be called nozomi. + +config MIPS_EJTAG_FDC_TTY + bool "MIPS EJTAG Fast Debug Channel TTY" + depends on MIPS_CDMM + help + This enables a TTY and console on the MIPS EJTAG Fast Debug Channels, + if they are present. This can be useful when working with an EJTAG + probe which supports it, to get console output and a login prompt via + EJTAG without needing to connect a serial cable. + + TTY devices are named e.g. ttyFDC3c2 (for FDC channel 2 of the FDC on + CPU3). + + The console can be enabled with console=fdc1 (for FDC channel 1 on all + CPUs). Do not use the console unless there is a debug probe attached + to drain the FDC TX FIFO. + + If unsure, say N. + +config MIPS_EJTAG_FDC_EARLYCON + bool "Early FDC console" + depends on MIPS_EJTAG_FDC_TTY + help + This registers a console on FDC channel 1 very early during boot (from + MIPS arch code). This is useful for bring-up and debugging early boot + issues. + + Do not enable unless there is a debug probe attached to drain the FDC + TX FIFO. + + If unsure, say N. + +config MIPS_EJTAG_FDC_KGDB + bool "Use KGDB over an FDC channel" + depends on MIPS_EJTAG_FDC_TTY && KGDB + default y + help + This enables the use of KGDB over an FDC channel, allowing KGDB to be + used remotely or when a serial port isn't available. + +config MIPS_EJTAG_FDC_KGDB_CHAN + int "KGDB FDC channel" + depends on MIPS_EJTAG_FDC_KGDB + range 2 15 + default 3 + help + FDC channel number to use for KGDB. + +config NULL_TTY + tristate "NULL TTY driver" + help + Say Y here if you want a NULL TTY which simply discards messages. + + This is useful to allow userspace applications which expect a console + device to work without modifications even when no console is + available or desired. + + In order to use this driver, you should redirect the console to this + TTY, or boot the kernel with console=ttynull. + + If unsure, say N. + +config VCC + tristate "Sun Virtual Console Concentrator" + depends on SUN_LDOMS + help + Support for Sun logical domain consoles. + +source "drivers/tty/hvc/Kconfig" + +config RPMSG_TTY + tristate "RPMSG tty driver" + depends on RPMSG + help + Say y here to export rpmsg endpoints as tty devices, usually found + in /dev/ttyRPMSGx. + This makes it possible for user-space programs to send and receive + rpmsg messages as a standard tty protocol. + + To compile this driver as a module, choose M here: the module will be + called rpmsg_tty. + +endif # TTY + +source "drivers/tty/serdev/Kconfig" -- cgit v1.2.3