From 5b7c4cabbb65f5c469464da6c5f614cbd7f730f2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Tue, 21 Feb 2023 18:24:12 -0800 Subject: Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core: - Add dedicated kmem_cache for typical/small skb->head, avoid having to access struct page at kfree time, and improve memory use. - Introduce sysctl to set default RPS configuration for new netdevs. - Define Netlink protocol specification format which can be used to describe messages used by each family and auto-generate parsers. Add tools for generating kernel data structures and uAPI headers. - Expose all net/core sysctls inside netns. - Remove 4s sleep in netpoll if carrier is instantly detected on boot. - Add configurable limit of MDB entries per port, and port-vlan. - Continue populating drop reasons throughout the stack. - Retire a handful of legacy Qdiscs and classifiers. Protocols: - Support IPv4 big TCP (TSO frames larger than 64kB). - Add IP_LOCAL_PORT_RANGE socket option, to control local port range on socket by socket basis. - Track and report in procfs number of MPTCP sockets used. - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path manager. - IPv6: don't check net.ipv6.route.max_size and rely on garbage collection to free memory (similarly to IPv4). - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986). - ICMP: add per-rate limit counters. - Add support for user scanning requests in ieee802154. - Remove static WEP support. - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting. - WiFi 7 EHT channel puncturing support (client & AP). BPF: - Add a rbtree data structure following the "next-gen data structure" precedent set by recently added linked list, that is, by using kfunc + kptr instead of adding a new BPF map type. - Expose XDP hints via kfuncs with initial support for RX hash and timestamp metadata. - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to better support decap on GRE tunnel devices not operating in collect metadata. - Improve x86 JIT's codegen for PROBE_MEM runtime error checks. - Remove the need for trace_printk_lock for bpf_trace_printk and bpf_trace_vprintk helpers. - Extend libbpf's bpf_tracing.h support for tracing arguments of kprobes/uprobes and syscall as a special case. - Significantly reduce the search time for module symbols by livepatch and BPF. - Enable cpumasks to be used as kptrs, which is useful for tracing programs tracking which tasks end up running on which CPUs in different time intervals. - Add support for BPF trampoline on s390x and riscv64. - Add capability to export the XDP features supported by the NIC. - Add __bpf_kfunc tag for marking kernel functions as kfuncs. - Add cgroup.memory=nobpf kernel parameter option to disable BPF memory accounting for container environments. Netfilter: - Remove the CLUSTERIP target. It has been marked as obsolete for years, and we still have WARN splats wrt races of the out-of-band /proc interface installed by this target. - Add 'destroy' commands to nf_tables. They are identical to the existing 'delete' commands, but do not return an error if the referenced object (set, chain, rule...) did not exist. Driver API: - Improve cpumask_local_spread() locality to help NICs set the right IRQ affinity on AMD platforms. - Separate C22 and C45 MDIO bus transactions more clearly. - Introduce new DCB table to control DSCP rewrite on egress. - Support configuration of Physical Layer Collision Avoidance (PLCA) Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of shared medium Ethernet. - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing preemption of low priority frames by high priority frames. - Add support for controlling MACSec offload using netlink SET. - Rework devlink instance refcounts to allow registration and de-registration under the instance lock. Split the code into multiple files, drop some of the unnecessarily granular locks and factor out common parts of netlink operation handling. - Add TX frame aggregation parameters (for USB drivers). - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning messages with notifications for debug. - Allow offloading of UDP NEW connections via act_ct. - Add support for per action HW stats in TC. - Support hardware miss to TC action (continue processing in SW from a specific point in the action chain). - Warn if old Wireless Extension user space interface is used with modern cfg80211/mac80211 drivers. Do not support Wireless Extensions for Wi-Fi 7 devices at all. Everyone should switch to using nl80211 interface instead. - Improve the CAN bit timing configuration. Use extack to return error messages directly to user space, update the SJW handling, including the definition of a new default value that will benefit CAN-FD controllers, by increasing their oscillator tolerance. New hardware / drivers: - Ethernet: - nVidia BlueField-3 support (control traffic driver) - Ethernet support for imx93 SoCs - Motorcomm yt8531 gigabit Ethernet PHY - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA) - Microchip LAN8841 PHY (incl. cable diagnostics and PTP) - Amlogic gxl MDIO mux - WiFi: - RealTek RTL8188EU (rtl8xxxu) - Qualcomm Wi-Fi 7 devices (ath12k) - CAN: - Renesas R-Car V4H Drivers: - Bluetooth: - Set Per Platform Antenna Gain (PPAG) for Intel controllers. - Ethernet NICs: - Intel (1G, igc): - support TSN / Qbv / packet scheduling features of i226 model - Intel (100G, ice): - use GNSS subsystem instead of TTY - multi-buffer XDP support - extend support for GPIO pins to E823 devices - nVidia/Mellanox: - update the shared buffer configuration on PFC commands - implement PTP adjphase function for HW offset control - TC support for Geneve and GRE with VF tunnel offload - more efficient crypto key management method - multi-port eswitch support - Netronome/Corigine: - add DCB IEEE support - support IPsec offloading for NFP3800 - Freescale/NXP (enetc): - support XDP_REDIRECT for XDP non-linear buffers - improve reconfig, avoid link flap and waiting for idle - support MAC Merge layer - Other NICs: - sfc/ef100: add basic devlink support for ef100 - ionic: rx_push mode operation (writing descriptors via MMIO) - bnxt: use the auxiliary bus abstraction for RDMA - r8169: disable ASPM and reset bus in case of tx timeout - cpsw: support QSGMII mode for J721e CPSW9G - cpts: support pulse-per-second output - ngbe: add an mdio bus driver - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing - r8152: handle devices with FW with NCM support - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation - virtio-net: support multi buffer XDP - virtio/vsock: replace virtio_vsock_pkt with sk_buff - tsnep: XDP support - Ethernet high-speed switches: - nVidia/Mellanox (mlxsw): - add support for latency TLV (in FW control messages) - Microchip (sparx5): - separate explicit and implicit traffic forwarding rules, make the implicit rules always active - add support for egress DSCP rewrite - IS0 VCAP support (Ingress Classification) - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS etc.) - ES2 VCAP support (Egress Access Control) - support for Per-Stream Filtering and Policing (802.1Q, 8.6.5.1) - Ethernet embedded switches: - Marvell (mv88e6xxx): - add MAB (port auth) offload support - enable PTP receive for mv88e6390 - NXP (ocelot): - support MAC Merge layer - support for the the vsc7512 internal copper phys - Microchip: - lan9303: convert to PHYLINK - lan966x: support TC flower filter statistics - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x - lan937x: support Credit Based Shaper configuration - ksz9477: support Energy Efficient Ethernet - other: - qca8k: convert to regmap read/write API, use bulk operations - rswitch: Improve TX timestamp accuracy - Intel WiFi (iwlwifi): - EHT (Wi-Fi 7) rate reporting - STEP equalizer support: transfer some STEP (connection to radio on platforms with integrated wifi) related parameters from the BIOS to the firmware. - Qualcomm 802.11ax WiFi (ath11k): - IPQ5018 support - Fine Timing Measurement (FTM) responder role support - channel 177 support - MediaTek WiFi (mt76): - per-PHY LED support - mt7996: EHT (Wi-Fi 7) support - Wireless Ethernet Dispatch (WED) reset support - switch to using page pool allocator - RealTek WiFi (rtw89): - support new version of Bluetooth co-existance - Mobile: - rmnet: support TX aggregation" * tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits) page_pool: add a comment explaining the fragment counter usage net: ethtool: fix __ethtool_dev_mm_supported() implementation ethtool: pse-pd: Fix double word in comments xsk: add linux/vmalloc.h to xsk.c sefltests: netdevsim: wait for devlink instance after netns removal selftest: fib_tests: Always cleanup before exit net/mlx5e: Align IPsec ASO result memory to be as required by hardware net/mlx5e: TC, Set CT miss to the specific ct action instance net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG net/mlx5: Refactor tc miss handling to a single function net/mlx5: Kconfig: Make tc offload depend on tc skb extension net/sched: flower: Support hardware miss to tc action net/sched: flower: Move filter handle initialization earlier net/sched: cls_api: Support hardware miss to tc action net/sched: Rename user cookie and act cookie sfc: fix builds without CONFIG_RTC_LIB sfc: clean up some inconsistent indentings net/mlx4_en: Introduce flexible array to silence overflow warning net: lan966x: Fix possible deadlock inside PTP net/ulp: Remove redundant ->clone() test in inet_clone_ulp(). ... --- include/dt-bindings/usb/pd.h | 468 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 468 insertions(+) create mode 100644 include/dt-bindings/usb/pd.h (limited to 'include/dt-bindings/usb/pd.h') diff --git a/include/dt-bindings/usb/pd.h b/include/dt-bindings/usb/pd.h new file mode 100644 index 000000000..e6526b138 --- /dev/null +++ b/include/dt-bindings/usb/pd.h @@ -0,0 +1,468 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __DT_POWER_DELIVERY_H +#define __DT_POWER_DELIVERY_H + +/* Power delivery Power Data Object definitions */ +#define PDO_TYPE_FIXED 0 +#define PDO_TYPE_BATT 1 +#define PDO_TYPE_VAR 2 +#define PDO_TYPE_APDO 3 + +#define PDO_TYPE_SHIFT 30 +#define PDO_TYPE_MASK 0x3 + +#define PDO_TYPE(t) ((t) << PDO_TYPE_SHIFT) + +#define PDO_VOLT_MASK 0x3ff +#define PDO_CURR_MASK 0x3ff +#define PDO_PWR_MASK 0x3ff + +#define PDO_FIXED_DUAL_ROLE (1 << 29) /* Power role swap supported */ +#define PDO_FIXED_SUSPEND (1 << 28) /* USB Suspend supported (Source) */ +#define PDO_FIXED_HIGHER_CAP (1 << 28) /* Requires more than vSafe5V (Sink) */ +#define PDO_FIXED_EXTPOWER (1 << 27) /* Externally powered */ +#define PDO_FIXED_USB_COMM (1 << 26) /* USB communications capable */ +#define PDO_FIXED_DATA_SWAP (1 << 25) /* Data role swap supported */ +#define PDO_FIXED_VOLT_SHIFT 10 /* 50mV units */ +#define PDO_FIXED_CURR_SHIFT 0 /* 10mA units */ + +#define PDO_FIXED_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_FIXED_VOLT_SHIFT) +#define PDO_FIXED_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) << PDO_FIXED_CURR_SHIFT) + +#define PDO_FIXED(mv, ma, flags) \ + (PDO_TYPE(PDO_TYPE_FIXED) | (flags) | \ + PDO_FIXED_VOLT(mv) | PDO_FIXED_CURR(ma)) + +#define VSAFE5V 5000 /* mv units */ + +#define PDO_BATT_MAX_VOLT_SHIFT 20 /* 50mV units */ +#define PDO_BATT_MIN_VOLT_SHIFT 10 /* 50mV units */ +#define PDO_BATT_MAX_PWR_SHIFT 0 /* 250mW units */ + +#define PDO_BATT_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_BATT_MIN_VOLT_SHIFT) +#define PDO_BATT_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_BATT_MAX_VOLT_SHIFT) +#define PDO_BATT_MAX_POWER(mw) ((((mw) / 250) & PDO_PWR_MASK) << PDO_BATT_MAX_PWR_SHIFT) + +#define PDO_BATT(min_mv, max_mv, max_mw) \ + (PDO_TYPE(PDO_TYPE_BATT) | PDO_BATT_MIN_VOLT(min_mv) | \ + PDO_BATT_MAX_VOLT(max_mv) | PDO_BATT_MAX_POWER(max_mw)) + +#define PDO_VAR_MAX_VOLT_SHIFT 20 /* 50mV units */ +#define PDO_VAR_MIN_VOLT_SHIFT 10 /* 50mV units */ +#define PDO_VAR_MAX_CURR_SHIFT 0 /* 10mA units */ + +#define PDO_VAR_MIN_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_VAR_MIN_VOLT_SHIFT) +#define PDO_VAR_MAX_VOLT(mv) ((((mv) / 50) & PDO_VOLT_MASK) << PDO_VAR_MAX_VOLT_SHIFT) +#define PDO_VAR_MAX_CURR(ma) ((((ma) / 10) & PDO_CURR_MASK) << PDO_VAR_MAX_CURR_SHIFT) + +#define PDO_VAR(min_mv, max_mv, max_ma) \ + (PDO_TYPE(PDO_TYPE_VAR) | PDO_VAR_MIN_VOLT(min_mv) | \ + PDO_VAR_MAX_VOLT(max_mv) | PDO_VAR_MAX_CURR(max_ma)) + +#define APDO_TYPE_PPS 0 + +#define PDO_APDO_TYPE_SHIFT 28 /* Only valid value currently is 0x0 - PPS */ +#define PDO_APDO_TYPE_MASK 0x3 + +#define PDO_APDO_TYPE(t) ((t) << PDO_APDO_TYPE_SHIFT) + +#define PDO_PPS_APDO_MAX_VOLT_SHIFT 17 /* 100mV units */ +#define PDO_PPS_APDO_MIN_VOLT_SHIFT 8 /* 100mV units */ +#define PDO_PPS_APDO_MAX_CURR_SHIFT 0 /* 50mA units */ + +#define PDO_PPS_APDO_VOLT_MASK 0xff +#define PDO_PPS_APDO_CURR_MASK 0x7f + +#define PDO_PPS_APDO_MIN_VOLT(mv) \ + ((((mv) / 100) & PDO_PPS_APDO_VOLT_MASK) << PDO_PPS_APDO_MIN_VOLT_SHIFT) +#define PDO_PPS_APDO_MAX_VOLT(mv) \ + ((((mv) / 100) & PDO_PPS_APDO_VOLT_MASK) << PDO_PPS_APDO_MAX_VOLT_SHIFT) +#define PDO_PPS_APDO_MAX_CURR(ma) \ + ((((ma) / 50) & PDO_PPS_APDO_CURR_MASK) << PDO_PPS_APDO_MAX_CURR_SHIFT) + +#define PDO_PPS_APDO(min_mv, max_mv, max_ma) \ + (PDO_TYPE(PDO_TYPE_APDO) | PDO_APDO_TYPE(APDO_TYPE_PPS) | \ + PDO_PPS_APDO_MIN_VOLT(min_mv) | PDO_PPS_APDO_MAX_VOLT(max_mv) | \ + PDO_PPS_APDO_MAX_CURR(max_ma)) + + /* + * Based on "Table 6-14 Fixed Supply PDO - Sink" of "USB Power Delivery Specification Revision 3.0, + * Version 1.2" + * Initial current capability of the new source when vSafe5V is applied. + */ +#define FRS_DEFAULT_POWER 1 +#define FRS_5V_1P5A 2 +#define FRS_5V_3A 3 + +/* + * SVDM Identity Header + * -------------------- + * <31> :: data capable as a USB host + * <30> :: data capable as a USB device + * <29:27> :: product type (UFP / Cable / VPD) + * <26> :: modal operation supported (1b == yes) + * <25:23> :: product type (DFP) (SVDM version 2.0+ only; set to zero in version 1.0) + * <22:21> :: connector type (SVDM version 2.0+ only; set to zero in version 1.0) + * <20:16> :: Reserved, Shall be set to zero + * <15:0> :: USB-IF assigned VID for this cable vendor + */ + +/* PD Rev2.0 definition */ +#define IDH_PTYPE_UNDEF 0 + +/* SOP Product Type (UFP) */ +#define IDH_PTYPE_NOT_UFP 0 +#define IDH_PTYPE_HUB 1 +#define IDH_PTYPE_PERIPH 2 +#define IDH_PTYPE_PSD 3 +#define IDH_PTYPE_AMA 5 + +/* SOP' Product Type (Cable Plug / VPD) */ +#define IDH_PTYPE_NOT_CABLE 0 +#define IDH_PTYPE_PCABLE 3 +#define IDH_PTYPE_ACABLE 4 +#define IDH_PTYPE_VPD 6 + +/* SOP Product Type (DFP) */ +#define IDH_PTYPE_NOT_DFP 0 +#define IDH_PTYPE_DFP_HUB 1 +#define IDH_PTYPE_DFP_HOST 2 +#define IDH_PTYPE_DFP_PB 3 + +#define VDO_IDH(usbh, usbd, ufp_cable, is_modal, dfp, conn, vid) \ + ((usbh) << 31 | (usbd) << 30 | ((ufp_cable) & 0x7) << 27 \ + | (is_modal) << 26 | ((dfp) & 0x7) << 23 | ((conn) & 0x3) << 21 \ + | ((vid) & 0xffff)) + +/* + * Cert Stat VDO + * ------------- + * <31:0> : USB-IF assigned XID for this cable + */ +#define VDO_CERT(xid) ((xid) & 0xffffffff) + +/* + * Product VDO + * ----------- + * <31:16> : USB Product ID + * <15:0> : USB bcdDevice + */ +#define VDO_PRODUCT(pid, bcd) (((pid) & 0xffff) << 16 | ((bcd) & 0xffff)) + +/* + * UFP VDO (PD Revision 3.0+ only) + * -------- + * <31:29> :: UFP VDO version + * <28> :: Reserved + * <27:24> :: Device capability + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) + * <21:11> :: Reserved + * <10:8> :: Vconn power (AMA only) + * <7> :: Vconn required (AMA only, 0b == no, 1b == yes) + * <6> :: Vbus required (AMA only, 0b == yes, 1b == no) + * <5:3> :: Alternate modes + * <2:0> :: USB highest speed + */ +/* UFP VDO Version */ +#define UFP_VDO_VER1_2 2 + +/* Device Capability */ +#define DEV_USB2_CAPABLE (1 << 0) +#define DEV_USB2_BILLBOARD (1 << 1) +#define DEV_USB3_CAPABLE (1 << 2) +#define DEV_USB4_CAPABLE (1 << 3) + +/* Connector Type */ +#define UFP_RECEPTACLE 2 +#define UFP_CAPTIVE 3 + +/* Vconn Power (AMA only, set to AMA_VCONN_NOT_REQ if Vconn is not required) */ +#define AMA_VCONN_PWR_1W 0 +#define AMA_VCONN_PWR_1W5 1 +#define AMA_VCONN_PWR_2W 2 +#define AMA_VCONN_PWR_3W 3 +#define AMA_VCONN_PWR_4W 4 +#define AMA_VCONN_PWR_5W 5 +#define AMA_VCONN_PWR_6W 6 + +/* Vconn Required (AMA only) */ +#define AMA_VCONN_NOT_REQ 0 +#define AMA_VCONN_REQ 1 + +/* Vbus Required (AMA only) */ +#define AMA_VBUS_REQ 0 +#define AMA_VBUS_NOT_REQ 1 + +/* Alternate Modes */ +#define UFP_ALTMODE_NOT_SUPP 0 +#define UFP_ALTMODE_TBT3 (1 << 0) +#define UFP_ALTMODE_RECFG (1 << 1) +#define UFP_ALTMODE_NO_RECFG (1 << 2) + +/* USB Highest Speed */ +#define UFP_USB2_ONLY 0 +#define UFP_USB32_GEN1 1 +#define UFP_USB32_4_GEN2 2 +#define UFP_USB4_GEN3 3 + +#define VDO_UFP(ver, cap, conn, vcpwr, vcr, vbr, alt, spd) \ + (((ver) & 0x7) << 29 | ((cap) & 0xf) << 24 | ((conn) & 0x3) << 22 \ + | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3 \ + | ((spd) & 0x7)) + +/* + * DFP VDO (PD Revision 3.0+ only) + * -------- + * <31:29> :: DFP VDO version + * <28:27> :: Reserved + * <26:24> :: Host capability + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) + * <21:5> :: Reserved + * <4:0> :: Port number + */ +#define DFP_VDO_VER1_1 1 +#define HOST_USB2_CAPABLE (1 << 0) +#define HOST_USB3_CAPABLE (1 << 1) +#define HOST_USB4_CAPABLE (1 << 2) +#define DFP_RECEPTACLE 2 +#define DFP_CAPTIVE 3 + +#define VDO_DFP(ver, cap, conn, pnum) \ + (((ver) & 0x7) << 29 | ((cap) & 0x7) << 24 | ((conn) & 0x3) << 22 \ + | ((pnum) & 0x1f)) + +/* + * Cable VDO (for both Passive and Active Cable VDO in PD Rev2.0) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:20> :: Reserved, Shall be set to zero + * <19:18> :: type-C to Type-A/B/C/Captive (00b == A, 01 == B, 10 == C, 11 == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (11b == both ends active VCONN req) + * <10> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable) + * <9> :: SSTX2 Directionality support + * <8> :: SSRX1 Directionality support + * <7> :: SSRX2 Directionality support + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4> :: Vbus through cable (0b == no, 1b == yes) + * <3> :: SOP" controller present? (0b == no, 1b == yes) + * <2:0> :: USB SS Signaling support + * + * Passive Cable VDO (PD Rev3.0+) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:21> :: VDO version + * <20> :: Reserved, Shall be set to zero + * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req) + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <8:7> :: Reserved, Shall be set to zero + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4:3> :: Reserved, Shall be set to zero + * <2:0> :: USB highest speed + * + * Active Cable VDO 1 (PD Rev3.0+) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:21> :: VDO version + * <20> :: Reserved, Shall be set to zero + * <19:18> :: Connector type (10b == C, 11b == Captive) + * <17> :: Reserved, Shall be set to zero + * <16:13> :: cable latency (0001 == <10ns(~1m length)) + * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req) + * <10:9> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <8> :: SBU supported (0b == supported, 1b == not supported) + * <7> :: SBU type (0b == passive, 1b == active) + * <6:5> :: Vbus current handling capability (01b == 3A, 10b == 5A) + * <4> :: Vbus through cable (0b == no, 1b == yes) + * <3> :: SOP" controller present? (0b == no, 1b == yes) + * <2:0> :: USB highest speed + */ +/* Cable VDO Version */ +#define CABLE_VDO_VER1_0 0 +#define CABLE_VDO_VER1_3 3 + +/* Connector Type (_ATYPE and _BTYPE are for PD Rev2.0 only) */ +#define CABLE_ATYPE 0 +#define CABLE_BTYPE 1 +#define CABLE_CTYPE 2 +#define CABLE_CAPTIVE 3 + +/* Cable Latency */ +#define CABLE_LATENCY_1M 1 +#define CABLE_LATENCY_2M 2 +#define CABLE_LATENCY_3M 3 +#define CABLE_LATENCY_4M 4 +#define CABLE_LATENCY_5M 5 +#define CABLE_LATENCY_6M 6 +#define CABLE_LATENCY_7M 7 +#define CABLE_LATENCY_7M_PLUS 8 + +/* Cable Termination Type */ +#define PCABLE_VCONN_NOT_REQ 0 +#define PCABLE_VCONN_REQ 1 +#define ACABLE_ONE_END 2 +#define ACABLE_BOTH_END 3 + +/* Maximum Vbus Voltage */ +#define CABLE_MAX_VBUS_20V 0 +#define CABLE_MAX_VBUS_30V 1 +#define CABLE_MAX_VBUS_40V 2 +#define CABLE_MAX_VBUS_50V 3 + +/* Active Cable SBU Supported/Type */ +#define ACABLE_SBU_SUPP 0 +#define ACABLE_SBU_NOT_SUPP 1 +#define ACABLE_SBU_PASSIVE 0 +#define ACABLE_SBU_ACTIVE 1 + +/* Vbus Current Handling Capability */ +#define CABLE_CURR_DEF 0 +#define CABLE_CURR_3A 1 +#define CABLE_CURR_5A 2 + +/* USB SuperSpeed Signaling Support (PD Rev2.0) */ +#define CABLE_USBSS_U2_ONLY 0 +#define CABLE_USBSS_U31_GEN1 1 +#define CABLE_USBSS_U31_GEN2 2 + +/* USB Highest Speed */ +#define CABLE_USB2_ONLY 0 +#define CABLE_USB32_GEN1 1 +#define CABLE_USB32_4_GEN2 2 +#define CABLE_USB4_GEN3 3 + +#define VDO_CABLE(hw, fw, cbl, lat, term, tx1d, tx2d, rx1d, rx2d, cur, vps, sopp, usbss) \ + (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 | ((cbl) & 0x3) << 18 \ + | ((lat) & 0x7) << 13 | ((term) & 0x3) << 11 | (tx1d) << 10 \ + | (tx2d) << 9 | (rx1d) << 8 | (rx2d) << 7 | ((cur) & 0x3) << 5 \ + | (vps) << 4 | (sopp) << 3 | ((usbss) & 0x7)) +#define VDO_PCABLE(hw, fw, ver, conn, lat, term, vbm, cur, spd) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ + | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7)) +#define VDO_ACABLE1(hw, fw, ver, conn, lat, term, vbm, sbu, sbut, cur, vbt, sopp, spd) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11 \ + | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5 \ + | (vbt) << 4 | (sopp) << 3 | ((spd) & 0x7)) + +/* + * Active Cable VDO 2 + * --------- + * <31:24> :: Maximum operating temperature + * <23:16> :: Shutdown temperature + * <15> :: Reserved, Shall be set to zero + * <14:12> :: U3/CLd power + * <11> :: U3 to U0 transition mode (0b == direct, 1b == through U3S) + * <10> :: Physical connection (0b == copper, 1b == optical) + * <9> :: Active element (0b == redriver, 1b == retimer) + * <8> :: USB4 supported (0b == yes, 1b == no) + * <7:6> :: USB2 hub hops consumed + * <5> :: USB2 supported (0b == yes, 1b == no) + * <4> :: USB3.2 supported (0b == yes, 1b == no) + * <3> :: USB lanes supported (0b == one lane, 1b == two lanes) + * <2> :: Optically isolated active cable (0b == no, 1b == yes) + * <1> :: Reserved, Shall be set to zero + * <0> :: USB gen (0b == gen1, 1b == gen2+) + */ +/* U3/CLd Power*/ +#define ACAB2_U3_CLD_10MW_PLUS 0 +#define ACAB2_U3_CLD_10MW 1 +#define ACAB2_U3_CLD_5MW 2 +#define ACAB2_U3_CLD_1MW 3 +#define ACAB2_U3_CLD_500UW 4 +#define ACAB2_U3_CLD_200UW 5 +#define ACAB2_U3_CLD_50UW 6 + +/* Other Active Cable VDO 2 Fields */ +#define ACAB2_U3U0_DIRECT 0 +#define ACAB2_U3U0_U3S 1 +#define ACAB2_PHY_COPPER 0 +#define ACAB2_PHY_OPTICAL 1 +#define ACAB2_REDRIVER 0 +#define ACAB2_RETIMER 1 +#define ACAB2_USB4_SUPP 0 +#define ACAB2_USB4_NOT_SUPP 1 +#define ACAB2_USB2_SUPP 0 +#define ACAB2_USB2_NOT_SUPP 1 +#define ACAB2_USB32_SUPP 0 +#define ACAB2_USB32_NOT_SUPP 1 +#define ACAB2_LANES_ONE 0 +#define ACAB2_LANES_TWO 1 +#define ACAB2_OPT_ISO_NO 0 +#define ACAB2_OPT_ISO_YES 1 +#define ACAB2_GEN_1 0 +#define ACAB2_GEN_2_PLUS 1 + +#define VDO_ACABLE2(mtemp, stemp, u3p, trans, phy, ele, u4, hops, u2, u32, lane, iso, gen) \ + (((mtemp) & 0xff) << 24 | ((stemp) & 0xff) << 16 | ((u3p) & 0x7) << 12 \ + | (trans) << 11 | (phy) << 10 | (ele) << 9 | (u4) << 8 \ + | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3 \ + | (iso) << 2 | (gen)) + +/* + * AMA VDO (PD Rev2.0) + * --------- + * <31:28> :: Cable HW version + * <27:24> :: Cable FW version + * <23:12> :: Reserved, Shall be set to zero + * <11> :: SSTX1 Directionality support (0b == fixed, 1b == cfgable) + * <10> :: SSTX2 Directionality support + * <9> :: SSRX1 Directionality support + * <8> :: SSRX2 Directionality support + * <7:5> :: Vconn power + * <4> :: Vconn power required + * <3> :: Vbus power required + * <2:0> :: USB SS Signaling support + */ +#define VDO_AMA(hw, fw, tx1d, tx2d, rx1d, rx2d, vcpwr, vcr, vbr, usbss) \ + (((hw) & 0x7) << 28 | ((fw) & 0x7) << 24 \ + | (tx1d) << 11 | (tx2d) << 10 | (rx1d) << 9 | (rx2d) << 8 \ + | ((vcpwr) & 0x7) << 5 | (vcr) << 4 | (vbr) << 3 \ + | ((usbss) & 0x7)) + +#define PD_VDO_AMA_VCONN_REQ(vdo) (((vdo) >> 4) & 1) +#define PD_VDO_AMA_VBUS_REQ(vdo) (((vdo) >> 3) & 1) + +#define AMA_USBSS_U2_ONLY 0 +#define AMA_USBSS_U31_GEN1 1 +#define AMA_USBSS_U31_GEN2 2 +#define AMA_USBSS_BBONLY 3 + +/* + * VPD VDO + * --------- + * <31:28> :: HW version + * <27:24> :: FW version + * <23:21> :: VDO version + * <20:17> :: Reserved, Shall be set to zero + * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V) + * <14> :: Charge through current support (0b == 3A, 1b == 5A) + * <13> :: Reserved, Shall be set to zero + * <12:7> :: Vbus impedance + * <6:1> :: Ground impedance + * <0> :: Charge through support (0b == no, 1b == yes) + */ +#define VPD_VDO_VER1_0 0 +#define VPD_MAX_VBUS_20V 0 +#define VPD_MAX_VBUS_30V 1 +#define VPD_MAX_VBUS_40V 2 +#define VPD_MAX_VBUS_50V 3 +#define VPDCT_CURR_3A 0 +#define VPDCT_CURR_5A 1 +#define VPDCT_NOT_SUPP 0 +#define VPDCT_SUPP 1 + +#define VDO_VPD(hw, fw, ver, vbm, curr, vbi, gi, ct) \ + (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21 \ + | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7 \ + | ((gi) & 0x3f) << 1 | (ct)) + +#endif /* __DT_POWER_DELIVERY_H */ -- cgit v1.2.3