Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 433 insertions, 0 deletions

diff --git a/Documentation/PCI/pci-error-recovery.rst b/Documentation/PCI/pci-error-recovery.rst
new file mode 100644
index 000000000..bdafeb4b6
--- /dev/null
+++ b/Documentation/PCI/pci-error-recovery.rst
@@ -0,0 +1,433 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==================
+PCI Error Recovery
+==================
+
+
+:Authors: - Linas Vepstas <linasvepstas@gmail.com>
+          - Richard Lary <rlary@us.ibm.com>
+          - Mike Mason <mmlnx@us.ibm.com>
+
+
+Many PCI bus controllers are able to detect a variety of hardware
+PCI errors on the bus, such as parity errors on the data and address
+buses, as well as SERR and PERR errors.  Some of the more advanced
+chipsets are able to deal with these errors; these include PCI-E chipsets,
+and the PCI-host bridges found on IBM Power4, Power5 and Power6-based
+pSeries boxes. A typical action taken is to disconnect the affected device,
+halting all I/O to it.  The goal of a disconnection is to avoid system
+corruption; for example, to halt system memory corruption due to DMA's
+to "wild" addresses. Typically, a reconnection mechanism is also
+offered, so that the affected PCI device(s) are reset and put back
+into working condition. The reset phase requires coordination
+between the affected device drivers and the PCI controller chip.
+This document describes a generic API for notifying device drivers
+of a bus disconnection, and then performing error recovery.
+This API is currently implemented in the 2.6.16 and later kernels.
+
+Reporting and recovery is performed in several steps. First, when
+a PCI hardware error has resulted in a bus disconnect, that event
+is reported as soon as possible to all affected device drivers,
+including multiple instances of a device driver on multi-function
+cards. This allows device drivers to avoid deadlocking in spinloops,
+waiting for some i/o-space register to change, when it never will.
+It also gives the drivers a chance to defer incoming I/O as
+needed.
+
+Next, recovery is performed in several stages. Most of the complexity
+is forced by the need to handle multi-function devices, that is,
+devices that have multiple device drivers associated with them.
+In the first stage, each driver is allowed to indicate what type
+of reset it desires, the choices being a simple re-enabling of I/O
+or requesting a slot reset.
+
+If any driver requests a slot reset, that is what will be done.
+
+After a reset and/or a re-enabling of I/O, all drivers are
+again notified, so that they may then perform any device setup/config
+that may be required.  After these have all completed, a final
+"resume normal operations" event is sent out.
+
+The biggest reason for choosing a kernel-based implementation rather
+than a user-space implementation was the need to deal with bus
+disconnects of PCI devices attached to storage media, and, in particular,
+disconnects from devices holding the root file system.  If the root
+file system is disconnected, a user-space mechanism would have to go
+through a large number of contortions to complete recovery. Almost all
+of the current Linux file systems are not tolerant of disconnection
+from/reconnection to their underlying block device. By contrast,
+bus errors are easy to manage in the device driver. Indeed, most
+device drivers already handle very similar recovery procedures;
+for example, the SCSI-generic layer already provides significant
+mechanisms for dealing with SCSI bus errors and SCSI bus resets.
+
+
+Detailed Design
+===============
+
+Design and implementation details below, based on a chain of
+public email discussions with Ben Herrenschmidt, circa 5 April 2005.
+
+The error recovery API support is exposed to the driver in the form of
+a structure of function pointers pointed to by a new field in struct
+pci_driver. A driver that fails to provide the structure is "non-aware",
+and the actual recovery steps taken are platform dependent.  The
+arch/powerpc implementation will simulate a PCI hotplug remove/add.
+
+This structure has the form::
+
+	struct pci_error_handlers
+	{
+		int (*error_detected)(struct pci_dev *dev, pci_channel_state_t);
+		int (*mmio_enabled)(struct pci_dev *dev);
+		int (*slot_reset)(struct pci_dev *dev);
+		void (*resume)(struct pci_dev *dev);
+		void (*cor_error_detected)(struct pci_dev *dev);
+	};
+
+The possible channel states are::
+
+	typedef enum {
+		pci_channel_io_normal,  /* I/O channel is in normal state */
+		pci_channel_io_frozen,  /* I/O to channel is blocked */
+		pci_channel_io_perm_failure, /* PCI card is dead */
+	} pci_channel_state_t;
+
+Possible return values are::
+
+	enum pci_ers_result {
+		PCI_ERS_RESULT_NONE,        /* no result/none/not supported in device driver */
+		PCI_ERS_RESULT_CAN_RECOVER, /* Device driver can recover without slot reset */
+		PCI_ERS_RESULT_NEED_RESET,  /* Device driver wants slot to be reset. */
+		PCI_ERS_RESULT_DISCONNECT,  /* Device has completely failed, is unrecoverable */
+		PCI_ERS_RESULT_RECOVERED,   /* Device driver is fully recovered and operational */
+	};
+
+A driver does not have to implement all of these callbacks; however,
+if it implements any, it must implement error_detected(). If a callback
+is not implemented, the corresponding feature is considered unsupported.
+For example, if mmio_enabled() and resume() aren't there, then it
+is assumed that the driver is not doing any direct recovery and requires
+a slot reset.  Typically a driver will want to know about
+a slot_reset().
+
+The actual steps taken by a platform to recover from a PCI error
+event will be platform-dependent, but will follow the general
+sequence described below.
+
+STEP 0: Error Event
+-------------------
+A PCI bus error is detected by the PCI hardware.  On powerpc, the slot
+is isolated, in that all I/O is blocked: all reads return 0xffffffff,
+all writes are ignored.
+
+
+STEP 1: Notification
+--------------------
+Platform calls the error_detected() callback on every instance of
+every driver affected by the error.
+
+At this point, the device might not be accessible anymore, depending on
+the platform (the slot will be isolated on powerpc). The driver may
+already have "noticed" the error because of a failing I/O, but this
+is the proper "synchronization point", that is, it gives the driver
+a chance to cleanup, waiting for pending stuff (timers, whatever, etc...)
+to complete; it can take semaphores, schedule, etc... everything but
+touch the device. Within this function and after it returns, the driver
+shouldn't do any new IOs. Called in task context. This is sort of a
+"quiesce" point. See note about interrupts at the end of this doc.
+
+All drivers participating in this system must implement this call.
+The driver must return one of the following result codes:
+
+  - PCI_ERS_RESULT_CAN_RECOVER
+      Driver returns this if it thinks it might be able to recover
+      the HW by just banging IOs or if it wants to be given
+      a chance to extract some diagnostic information (see
+      mmio_enable, below).
+  - PCI_ERS_RESULT_NEED_RESET
+      Driver returns this if it can't recover without a
+      slot reset.
+  - PCI_ERS_RESULT_DISCONNECT
+      Driver returns this if it doesn't want to recover at all.
+
+The next step taken will depend on the result codes returned by the
+drivers.
+
+If all drivers on the segment/slot return PCI_ERS_RESULT_CAN_RECOVER,
+then the platform should re-enable IOs on the slot (or do nothing in
+particular, if the platform doesn't isolate slots), and recovery
+proceeds to STEP 2 (MMIO Enable).
+
+If any driver requested a slot reset (by returning PCI_ERS_RESULT_NEED_RESET),
+then recovery proceeds to STEP 4 (Slot Reset).
+
+If the platform is unable to recover the slot, the next step
+is STEP 6 (Permanent Failure).
+
+.. note::
+
+   The current powerpc implementation assumes that a device driver will
+   *not* schedule or semaphore in this routine; the current powerpc
+   implementation uses one kernel thread to notify all devices;
+   thus, if one device sleeps/schedules, all devices are affected.
+   Doing better requires complex multi-threaded logic in the error
+   recovery implementation (e.g. waiting for all notification threads
+   to "join" before proceeding with recovery.)  This seems excessively
+   complex and not worth implementing.
+
+   The current powerpc implementation doesn't much care if the device
+   attempts I/O at this point, or not.  I/O's will fail, returning
+   a value of 0xff on read, and writes will be dropped. If more than
+   EEH_MAX_FAILS I/O's are attempted to a frozen adapter, EEH
+   assumes that the device driver has gone into an infinite loop
+   and prints an error to syslog.  A reboot is then required to
+   get the device working again.
+
+STEP 2: MMIO Enabled
+--------------------
+The platform re-enables MMIO to the device (but typically not the
+DMA), and then calls the mmio_enabled() callback on all affected
+device drivers.
+
+This is the "early recovery" call. IOs are allowed again, but DMA is
+not, with some restrictions. This is NOT a callback for the driver to
+start operations again, only to peek/poke at the device, extract diagnostic
+information, if any, and eventually do things like trigger a device local
+reset or some such, but not restart operations. This callback is made if
+all drivers on a segment agree that they can try to recover and if no automatic
+link reset was performed by the HW. If the platform can't just re-enable IOs
+without a slot reset or a link reset, it will not call this callback, and
+instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
+
+.. note::
+
+   The following is proposed; no platform implements this yet:
+   Proposal: All I/O's should be done _synchronously_ from within
+   this callback, errors triggered by them will be returned via
+   the normal pci_check_whatever() API, no new error_detected()
+   callback will be issued due to an error happening here. However,
+   such an error might cause IOs to be re-blocked for the whole
+   segment, and thus invalidate the recovery that other devices
+   on the same segment might have done, forcing the whole segment
+   into one of the next states, that is, link reset or slot reset.
+
+The driver should return one of the following result codes:
+  - PCI_ERS_RESULT_RECOVERED
+      Driver returns this if it thinks the device is fully
+      functional and thinks it is ready to start
+      normal driver operations again. There is no
+      guarantee that the driver will actually be
+      allowed to proceed, as another driver on the
+      same segment might have failed and thus triggered a
+      slot reset on platforms that support it.
+
+  - PCI_ERS_RESULT_NEED_RESET
+      Driver returns this if it thinks the device is not
+      recoverable in its current state and it needs a slot
+      reset to proceed.
+
+  - PCI_ERS_RESULT_DISCONNECT
+      Same as above. Total failure, no recovery even after
+      reset driver dead. (To be defined more precisely)
+
+The next step taken depends on the results returned by the drivers.
+If all drivers returned PCI_ERS_RESULT_RECOVERED, then the platform
+proceeds to either STEP3 (Link Reset) or to STEP 5 (Resume Operations).
+
+If any driver returned PCI_ERS_RESULT_NEED_RESET, then the platform
+proceeds to STEP 4 (Slot Reset)
+
+STEP 3: Link Reset
+------------------
+The platform resets the link.  This is a PCI-Express specific step
+and is done whenever a fatal error has been detected that can be
+"solved" by resetting the link.
+
+STEP 4: Slot Reset
+------------------
+
+In response to a return value of PCI_ERS_RESULT_NEED_RESET, the
+platform will perform a slot reset on the requesting PCI device(s).
+The actual steps taken by a platform to perform a slot reset
+will be platform-dependent. Upon completion of slot reset, the
+platform will call the device slot_reset() callback.
+
+Powerpc platforms implement two levels of slot reset:
+soft reset(default) and fundamental(optional) reset.
+
+Powerpc soft reset consists of asserting the adapter #RST line and then
+restoring the PCI BAR's and PCI configuration header to a state
+that is equivalent to what it would be after a fresh system
+power-on followed by power-on BIOS/system firmware initialization.
+Soft reset is also known as hot-reset.
+
+Powerpc fundamental reset is supported by PCI Express cards only
+and results in device's state machines, hardware logic, port states and
+configuration registers to initialize to their default conditions.
+
+For most PCI devices, a soft reset will be sufficient for recovery.
+Optional fundamental reset is provided to support a limited number
+of PCI Express devices for which a soft reset is not sufficient
+for recovery.
+
+If the platform supports PCI hotplug, then the reset might be
+performed by toggling the slot electrical power off/on.
+
+It is important for the platform to restore the PCI config space
+to the "fresh poweron" state, rather than the "last state". After
+a slot reset, the device driver will almost always use its standard
+device initialization routines, and an unusual config space setup
+may result in hung devices, kernel panics, or silent data corruption.
+
+This call gives drivers the chance to re-initialize the hardware
+(re-download firmware, etc.).  At this point, the driver may assume
+that the card is in a fresh state and is fully functional. The slot
+is unfrozen and the driver has full access to PCI config space,
+memory mapped I/O space and DMA. Interrupts (Legacy, MSI, or MSI-X)
+will also be available.
+
+Drivers should not restart normal I/O processing operations
+at this point.  If all device drivers report success on this
+callback, the platform will call resume() to complete the sequence,
+and let the driver restart normal I/O processing.
+
+A driver can still return a critical failure for this function if
+it can't get the device operational after reset.  If the platform
+previously tried a soft reset, it might now try a hard reset (power
+cycle) and then call slot_reset() again.  If the device still can't
+be recovered, there is nothing more that can be done;  the platform
+will typically report a "permanent failure" in such a case.  The
+device will be considered "dead" in this case.
+
+Drivers for multi-function cards will need to coordinate among
+themselves as to which driver instance will perform any "one-shot"
+or global device initialization. For example, the Symbios sym53cxx2
+driver performs device init only from PCI function 0::
+
+	+       if (PCI_FUNC(pdev->devfn) == 0)
+	+               sym_reset_scsi_bus(np, 0);
+
+Result codes:
+	- PCI_ERS_RESULT_DISCONNECT
+	  Same as above.
+
+Drivers for PCI Express cards that require a fundamental reset must
+set the needs_freset bit in the pci_dev structure in their probe function.
+For example, the QLogic qla2xxx driver sets the needs_freset bit for certain
+PCI card types::
+
+	+	/* Set EEH reset type to fundamental if required by hba  */
+	+	if (IS_QLA24XX(ha) || IS_QLA25XX(ha) || IS_QLA81XX(ha))
+	+		pdev->needs_freset = 1;
+	+
+
+Platform proceeds either to STEP 5 (Resume Operations) or STEP 6 (Permanent
+Failure).
+
+.. note::
+
+   The current powerpc implementation does not try a power-cycle
+   reset if the driver returned PCI_ERS_RESULT_DISCONNECT.
+   However, it probably should.
+
+
+STEP 5: Resume Operations
+-------------------------
+The platform will call the resume() callback on all affected device
+drivers if all drivers on the segment have returned
+PCI_ERS_RESULT_RECOVERED from one of the 3 previous callbacks.
+The goal of this callback is to tell the driver to restart activity,
+that everything is back and running. This callback does not return
+a result code.
+
+At this point, if a new error happens, the platform will restart
+a new error recovery sequence.
+
+STEP 6: Permanent Failure
+-------------------------
+A "permanent failure" has occurred, and the platform cannot recover
+the device.  The platform will call error_detected() with a
+pci_channel_state_t value of pci_channel_io_perm_failure.
+
+The device driver should, at this point, assume the worst. It should
+cancel all pending I/O, refuse all new I/O, returning -EIO to
+higher layers. The device driver should then clean up all of its
+memory and remove itself from kernel operations, much as it would
+during system shutdown.
+
+The platform will typically notify the system operator of the
+permanent failure in some way.  If the device is hotplug-capable,
+the operator will probably want to remove and replace the device.
+Note, however, not all failures are truly "permanent". Some are
+caused by over-heating, some by a poorly seated card. Many
+PCI error events are caused by software bugs, e.g. DMA's to
+wild addresses or bogus split transactions due to programming
+errors. See the discussion in powerpc/eeh-pci-error-recovery.txt
+for additional detail on real-life experience of the causes of
+software errors.
+
+
+Conclusion; General Remarks
+---------------------------
+The way the callbacks are called is platform policy. A platform with
+no slot reset capability may want to just "ignore" drivers that can't
+recover (disconnect them) and try to let other cards on the same segment
+recover. Keep in mind that in most real life cases, though, there will
+be only one driver per segment.
+
+Now, a note about interrupts. If you get an interrupt and your
+device is dead or has been isolated, there is a problem :)
+The current policy is to turn this into a platform policy.
+That is, the recovery API only requires that:
+
+ - There is no guarantee that interrupt delivery can proceed from any
+   device on the segment starting from the error detection and until the
+   slot_reset callback is called, at which point interrupts are expected
+   to be fully operational.
+
+ - There is no guarantee that interrupt delivery is stopped, that is,
+   a driver that gets an interrupt after detecting an error, or that detects
+   an error within the interrupt handler such that it prevents proper
+   ack'ing of the interrupt (and thus removal of the source) should just
+   return IRQ_NOTHANDLED. It's up to the platform to deal with that
+   condition, typically by masking the IRQ source during the duration of
+   the error handling. It is expected that the platform "knows" which
+   interrupts are routed to error-management capable slots and can deal
+   with temporarily disabling that IRQ number during error processing (this
+   isn't terribly complex). That means some IRQ latency for other devices
+   sharing the interrupt, but there is simply no other way. High end
+   platforms aren't supposed to share interrupts between many devices
+   anyway :)
+
+.. note::
+
+   Implementation details for the powerpc platform are discussed in
+   the file Documentation/powerpc/eeh-pci-error-recovery.rst
+
+   As of this writing, there is a growing list of device drivers with
+   patches implementing error recovery. Not all of these patches are in
+   mainline yet. These may be used as "examples":
+
+   - drivers/scsi/ipr
+   - drivers/scsi/sym53c8xx_2
+   - drivers/scsi/qla2xxx
+   - drivers/scsi/lpfc
+   - drivers/next/bnx2.c
+   - drivers/next/e100.c
+   - drivers/net/e1000
+   - drivers/net/e1000e
+   - drivers/net/ixgb
+   - drivers/net/ixgbe
+   - drivers/net/cxgb3
+   - drivers/net/s2io.c
+
+   The cor_error_detected() callback is invoked in handle_error_source() when
+   the error severity is "correctable". The callback is optional and allows
+   additional logging to be done if desired. See example:
+
+   - drivers/cxl/pci.c
+
+The End
+-------