Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

6 files changed, 318 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
new file mode 100644
index 000000000..606b4b1b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
@@ -0,0 +1,84 @@
+QCOM Idle States for cpuidle driver
+
+ARM provides idle-state node to define the cpuidle states, as defined in [1].
+cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
+states. Idle states have different enter/exit latency and residency values.
+The idle states supported by the QCOM SoC are defined as -
+
+    * Standby
+    * Retention
+    * Standalone Power Collapse (Standalone PC or SPC)
+    * Power Collapse (PC)
+
+Standby: Standby does a little more in addition to architectural clock gating.
+When the WFI instruction is executed the ARM core would gate its internal
+clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
+trigger to execute the SPM state machine. The SPM state machine waits for the
+interrupt to trigger the core back in to active. This triggers the cache
+hierarchy to enter standby states, when all cpus are idle. An interrupt brings
+the SPM state machine out of its wait, the next step is to ensure that the
+cache hierarchy is also out of standby, and then the cpu is allowed to resume
+execution. This state is defined as a generic ARM WFI state by the ARM cpuidle
+driver and is not defined in the DT. The SPM state machine should be
+configured to execute this state by default and after executing every other
+state below.
+
+Retention: Retention is a low power state where the core is clock gated and
+the memory and the registers associated with the core are retained. The
+voltage may be reduced to the minimum value needed to keep the processor
+registers active. The SPM should be configured to execute the retention
+sequence and would wait for interrupt, before restoring the cpu to execution
+state. Retention may have a slightly higher latency than Standby.
+
+Standalone PC: A cpu can power down and warmboot if there is a sufficient time
+between the time it enters idle and the next known wake up. SPC mode is used
+to indicate a core entering a power down state without consulting any other
+cpu or the system resources. This helps save power only on that core.  The SPM
+sequence for this idle state is programmed to power down the supply to the
+core, wait for the interrupt, restore power to the core, and ensure the
+system state including cache hierarchy is ready before allowing core to
+resume. Applying power and resetting the core causes the core to warmboot
+back into Elevation Level (EL) which trampolines the control back to the
+kernel. Entering a power down state for the cpu, needs to be done by trapping
+into a EL. Failing to do so, would result in a crash enforced by the warm boot
+code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
+be flushed in s/w, before powering down the core.
+
+Power Collapse: This state is similar to the SPC mode, but distinguishes
+itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
+modes. In a hierarchical power domain SoC, this means L2 and other caches can
+be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
+voltages reduced, provided all cpus enter this state.  Since the span of low
+power modes possible at this state is vast, the exit latency and the residency
+of this low power mode would be considered high even though at a cpu level,
+this essentially is cpu power down. The SPM in this state also may handshake
+with the Resource power manager (RPM) processor in the SoC to indicate a
+complete application processor subsystem shut down.
+
+The idle-state for QCOM SoCs are distinguished by the compatible property of
+the idle-states device node.
+
+The devicetree representation of the idle state should be -
+
+Required properties:
+
+- compatible: Must be one of -
+			"qcom,idle-state-ret",
+			"qcom,idle-state-spc",
+			"qcom,idle-state-pc",
+		and "arm,idle-state".
+
+Other required and optional properties are specified in [1].
+
+Example:
+
+	idle-states {
+		CPU_SPC: spc {
+			compatible = "qcom,idle-state-spc", "arm,idle-state";
+			entry-latency-us = <150>;
+			exit-latency-us = <200>;
+			min-residency-us = <2000>;
+		};
+	};
+
+[1]. Documentation/devicetree/bindings/cpu/idle-states.yaml
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
new file mode 100644
index 000000000..7f696362a
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
@@ -0,0 +1,49 @@
+Krait Processor Sub-system (KPSS) Application Clock Controller (ACC)
+
+The KPSS ACC provides clock, power domain, and reset control to a Krait CPU.
+There is one ACC register region per CPU within the KPSS remapped region as
+well as an alias register region that remaps accesses to the ACC associated
+with the CPU accessing the region.
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: should be one of:
+			"qcom,kpss-acc-v1"
+			"qcom,kpss-acc-v2"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the first element specifies the base address and size of
+		    the register region. An optional second element specifies
+		    the base address and size of the alias register region.
+
+- clocks:
+        Usage: required
+        Value type: <prop-encoded-array>
+        Definition: reference to the pll parents.
+
+- clock-names:
+        Usage: required
+        Value type: <stringlist>
+        Definition: must be "pll8_vote", "pxo".
+
+- clock-output-names:
+	Usage: optional
+	Value type: <string>
+	Definition: Name of the output clock. Typically acpuX_aux where X is a
+		    CPU number starting at 0.
+
+Example:
+
+	clock-controller@2088000 {
+		compatible = "qcom,kpss-acc-v2";
+		reg = <0x02088000 0x1000>,
+		      <0x02008000 0x1000>;
+		clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
+		clock-names = "pll8_vote", "pxo";
+		clock-output-names = "acpu0_aux";
+	};
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
new file mode 100644
index 000000000..e62875895
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
@@ -0,0 +1,44 @@
+Krait Processor Sub-system (KPSS) Global Clock Controller (GCC)
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: should be one of the following. The generic compatible
+			"qcom,kpss-gcc" should also be included.
+			"qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc"
+			"qcom,kpss-gcc-apq8064", "qcom,kpss-gcc"
+			"qcom,kpss-gcc-msm8974", "qcom,kpss-gcc"
+			"qcom,kpss-gcc-msm8960", "qcom,kpss-gcc"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: base address and size of the register region
+
+- clocks:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: reference to the pll parents.
+
+- clock-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "pll8_vote", "pxo".
+
+- clock-output-names:
+	Usage: required
+	Value type: <string>
+	Definition: Name of the output clock. Typically acpu_l2_aux indicating
+		    an L2 cache auxiliary clock.
+
+Example:
+
+	l2cc: clock-controller@2011000 {
+		compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc";
+		reg = <0x2011000 0x1000>;
+		clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
+		clock-names = "pll8_vote", "pxo";
+		clock-output-names = "acpu_l2_aux";
+	};
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml
new file mode 100644
index 000000000..38efcad56
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,llcc.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/msm/qcom,llcc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Last Level Cache Controller
+
+maintainers:
+  - Rishabh Bhatnagar <rishabhb@codeaurora.org>
+  - Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
+
+description: |
+  LLCC (Last Level Cache Controller) provides last level of cache memory in SoC,
+  that can be shared by multiple clients. Clients here are different cores in the
+  SoC, the idea is to minimize the local caches at the clients and migrate to
+  common pool of memory. Cache memory is divided into partitions called slices
+  which are assigned to clients. Clients can query the slice details, activate
+  and deactivate them.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc7180-llcc
+      - qcom,sc7280-llcc
+      - qcom,sc8180x-llcc
+      - qcom,sc8280xp-llcc
+      - qcom,sdm845-llcc
+      - qcom,sm6350-llcc
+      - qcom,sm8150-llcc
+      - qcom,sm8250-llcc
+      - qcom,sm8350-llcc
+      - qcom,sm8450-llcc
+      - qcom,sm8550-llcc
+
+  reg:
+    items:
+      - description: LLCC base register region
+      - description: LLCC broadcast base register region
+
+  reg-names:
+    items:
+      - const: llcc_base
+      - const: llcc_broadcast_base
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    system-cache-controller@1100000 {
+      compatible = "qcom,sdm845-llcc";
+      reg = <0x1100000 0x200000>, <0x1300000 0x50000> ;
+      reg-names = "llcc_base", "llcc_broadcast_base";
+      interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
+    };
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
new file mode 100644
index 000000000..c0e3c3a42
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
@@ -0,0 +1,58 @@
+SPM AVS Wrapper 2 (SAW2)
+
+The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the
+Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable
+power-controller that transitions a piece of hardware (like a processor or
+subsystem) into and out of low power modes via a direct connection to
+the PMIC. It can also be wired up to interact with other processors in the
+system, notifying them when a low power state is entered or exited.
+
+Multiple revisions of the SAW hardware are supported using these Device Nodes.
+SAW2 revisions differ in the register offset and configuration data. Also, the
+same revision of the SAW in different SoCs may have different configuration
+data due the differences in hardware capabilities. Hence the SoC name, the
+version of the SAW hardware in that SoC and the distinction between cpu (big
+or Little) or cache, may be needed to uniquely identify the SAW register
+configuration and initialization data. The compatible string is used to
+indicate this parameter.
+
+PROPERTIES
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: Must have
+			"qcom,saw2"
+		    A more specific value could be one of:
+			"qcom,apq8064-saw2-v1.1-cpu"
+			"qcom,msm8226-saw2-v2.1-cpu"
+			"qcom,msm8974-saw2-v2.1-cpu"
+			"qcom,apq8084-saw2-v2.1-cpu"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the first element specifies the base address and size of
+		    the register region. An optional second element specifies
+		    the base address and size of the alias register region.
+
+- regulator:
+	Usage: optional
+	Value type: boolean
+	Definition: Indicates that this SPM device acts as a regulator device
+			device for the core (CPU or Cache) the SPM is attached
+			to.
+
+Example 1:
+
+	power-controller@2099000 {
+		compatible = "qcom,saw2";
+		reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+		regulator;
+	};
+
+Example 2:
+	saw0: power-controller@f9089000 {
+		compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
+		reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/msm/ssbi.txt b/Documentation/devicetree/bindings/arm/msm/ssbi.txt
new file mode 100644
index 000000000..54fd5ced3
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/ssbi.txt
@@ -0,0 +1,18 @@
+* Qualcomm SSBI
+
+Some Qualcomm MSM devices contain a point-to-point serial bus used to
+communicate with a limited range of devices (mostly power management
+chips).
+
+These require the following properties:
+
+- compatible: "qcom,ssbi"
+
+- qcom,controller-type
+  indicates the SSBI bus variant the controller should use to talk
+  with the slave device.  This should be one of "ssbi", "ssbi2", or
+  "pmic-arbiter".  The type chosen is determined by the attached
+  slave.
+
+The slave device should be the single child node of the ssbi device
+with a compatible field.