Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 331 insertions, 0 deletions

diff --git a/Documentation/networking/device_drivers/can/can327.rst b/Documentation/networking/device_drivers/can/can327.rst
new file mode 100644
index 000000000..b87bfbe5d
--- /dev/null
+++ b/Documentation/networking/device_drivers/can/can327.rst
@@ -0,0 +1,331 @@
+.. SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+
+can327: ELM327 driver for Linux SocketCAN
+==========================================
+
+Authors
+--------
+
+Max Staudt <max@enpas.org>
+
+
+
+Motivation
+-----------
+
+This driver aims to lower the initial cost for hackers interested in
+working with CAN buses.
+
+CAN adapters are expensive, few, and far between.
+ELM327 interfaces are cheap and plentiful.
+Let's use ELM327s as CAN adapters.
+
+
+
+Introduction
+-------------
+
+This driver is an effort to turn abundant ELM327 based OBD interfaces
+into full fledged (as far as possible) CAN interfaces.
+
+Since the ELM327 was never meant to be a stand alone CAN controller,
+the driver has to switch between its modes as quickly as possible in
+order to fake full-duplex operation.
+
+As such, can327 is a best effort driver. However, this is more than
+enough to implement simple request-response protocols (such as OBD II),
+and to monitor broadcast messages on a bus (such as in a vehicle).
+
+Most ELM327s come as nondescript serial devices, attached via USB or
+Bluetooth. The driver cannot recognize them by itself, and as such it
+is up to the user to attach it in form of a TTY line discipline
+(similar to PPP, SLIP, slcan, ...).
+
+This driver is meant for ELM327 versions 1.4b and up, see below for
+known limitations in older controllers and clones.
+
+
+
+Data sheet
+-----------
+
+The official data sheets can be found at ELM electronics' home page:
+
+  https://www.elmelectronics.com/
+
+
+
+How to attach the line discipline
+----------------------------------
+
+Every ELM327 chip is factory programmed to operate at a serial setting
+of 38400 baud/s, 8 data bits, no parity, 1 stopbit.
+
+If you have kept this default configuration, the line discipline can
+be attached on a command prompt as follows::
+
+    sudo ldattach \
+           --debug \
+           --speed 38400 \
+           --eightbits \
+           --noparity \
+           --onestopbit \
+           --iflag -ICRNL,INLCR,-IXOFF \
+           30 \
+           /dev/ttyUSB0
+
+To change the ELM327's serial settings, please refer to its data
+sheet. This needs to be done before attaching the line discipline.
+
+Once the ldisc is attached, the CAN interface starts out unconfigured.
+Set the speed before starting it::
+
+    # The interface needs to be down to change parameters
+    sudo ip link set can0 down
+    sudo ip link set can0 type can bitrate 500000
+    sudo ip link set can0 up
+
+500000 bit/s is a common rate for OBD-II diagnostics.
+If you're connecting straight to a car's OBD port, this is the speed
+that most cars (but not all!) expect.
+
+After this, you can set out as usual with candump, cansniffer, etc.
+
+
+
+How to check the controller version
+------------------------------------
+
+Use a terminal program to attach to the controller.
+
+After issuing the "``AT WS``" command, the controller will respond with
+its version::
+
+    >AT WS
+
+
+    ELM327 v1.4b
+
+    >
+
+Note that clones may claim to be any version they like.
+It is not indicative of their actual feature set.
+
+
+
+
+Communication example
+----------------------
+
+This is a short and incomplete introduction on how to talk to an ELM327.
+It is here to guide understanding of the controller's and the driver's
+limitation (listed below) as well as manual testing.
+
+
+The ELM327 has two modes:
+
+- Command mode
+- Reception mode
+
+In command mode, it expects one command per line, terminated by CR.
+By default, the prompt is a "``>``", after which a command can be
+entered::
+
+    >ATE1
+    OK
+    >
+
+The init script in the driver switches off several configuration options
+that are only meaningful in the original OBD scenario the chip is meant
+for, and are actually a hindrance for can327.
+
+
+When a command is not recognized, such as by an older version of the
+ELM327, a question mark is printed as a response instead of OK::
+
+    >ATUNKNOWN
+    ?
+    >
+
+At present, can327 does not evaluate this response. See the section
+below on known limitations for details.
+
+
+When a CAN frame is to be sent, the target address is configured, after
+which the frame is sent as a command that consists of the data's hex
+dump::
+
+    >ATSH123
+    OK
+    >DEADBEEF12345678
+    OK
+    >
+
+The above interaction sends the SFF frame "``DE AD BE EF 12 34 56 78``"
+with (11 bit) CAN ID ``0x123``.
+For this to function, the controller must be configured for SFF sending
+mode (using "``AT PB``", see code or datasheet).
+
+
+Once a frame has been sent and wait-for-reply mode is on (``ATR1``,
+configured on ``listen-only=off``), or when the reply timeout expires
+and the driver sets the controller into monitoring mode (``ATMA``),
+the ELM327 will send one line for each received CAN frame, consisting
+of CAN ID, DLC, and data::
+
+    123 8 DEADBEEF12345678
+
+For EFF (29 bit) CAN frames, the address format is slightly different,
+which can327 uses to tell the two apart::
+
+    12 34 56 78 8 DEADBEEF12345678
+
+The ELM327 will receive both SFF and EFF frames - the current CAN
+config (``ATPB``) does not matter.
+
+
+If the ELM327's internal UART sending buffer runs full, it will abort
+the monitoring mode, print "BUFFER FULL" and drop back into command
+mode. Note that in this case, unlike with other error messages, the
+error message may appear on the same line as the last (usually
+incomplete) data frame::
+
+    12 34 56 78 8 DEADBEEF123 BUFFER FULL
+
+
+
+Known limitations of the controller
+------------------------------------
+
+- Clone devices ("v1.5" and others)
+
+  Sending RTR frames is not supported and will be dropped silently.
+
+  Receiving RTR with DLC 8 will appear to be a regular frame with
+  the last received frame's DLC and payload.
+
+  "``AT CSM``" (CAN Silent Monitoring, i.e. don't send CAN ACKs) is
+  not supported, and is hard coded to ON. Thus, frames are not ACKed
+  while listening: "``AT MA``" (Monitor All) will always be "silent".
+  However, immediately after sending a frame, the ELM327 will be in
+  "receive reply" mode, in which it *does* ACK any received frames.
+  Once the bus goes silent, or an error occurs (such as BUFFER FULL),
+  or the receive reply timeout runs out, the ELM327 will end reply
+  reception mode on its own and can327 will fall back to "``AT MA``"
+  in order to keep monitoring the bus.
+
+  Other limitations may apply, depending on the clone and the quality
+  of its firmware.
+
+
+- All versions
+
+  No full duplex operation is supported. The driver will switch
+  between input/output mode as quickly as possible.
+
+  The length of outgoing RTR frames cannot be set. In fact, some
+  clones (tested with one identifying as "``v1.5``") are unable to
+  send RTR frames at all.
+
+  We don't have a way to get real-time notifications on CAN errors.
+  While there is a command (``AT CS``) to retrieve some basic stats,
+  we don't poll it as it would force us to interrupt reception mode.
+
+
+- Versions prior to 1.4b
+
+  These versions do not send CAN ACKs when in monitoring mode (AT MA).
+  However, they do send ACKs while waiting for a reply immediately
+  after sending a frame. The driver maximizes this time to make the
+  controller as useful as possible.
+
+  Starting with version 1.4b, the ELM327 supports the "``AT CSM``"
+  command, and the "listen-only" CAN option will take effect.
+
+
+- Versions prior to 1.4
+
+  These chips do not support the "``AT PB``" command, and thus cannot
+  change bitrate or SFF/EFF mode on-the-fly. This will have to be
+  programmed by the user before attaching the line discipline. See the
+  data sheet for details.
+
+
+- Versions prior to 1.3
+
+  These chips cannot be used at all with can327. They do not support
+  the "``AT D1``" command, which is necessary to avoid parsing conflicts
+  on incoming data, as well as distinction of RTR frame lengths.
+
+  Specifically, this allows for easy distinction of SFF and EFF
+  frames, and to check whether frames are complete. While it is possible
+  to deduce the type and length from the length of the line the ELM327
+  sends us, this method fails when the ELM327's UART output buffer
+  overruns. It may abort sending in the middle of the line, which will
+  then be mistaken for something else.
+
+
+
+Known limitations of the driver
+--------------------------------
+
+- No 8/7 timing.
+
+  ELM327 can only set CAN bitrates that are of the form 500000/n, where
+  n is an integer divisor.
+  However there is an exception: With a separate flag, it may set the
+  speed to be 8/7 of the speed indicated by the divisor.
+  This mode is not currently implemented.
+
+- No evaluation of command responses.
+
+  The ELM327 will reply with OK when a command is understood, and with ?
+  when it is not. The driver does not currently check this, and simply
+  assumes that the chip understands every command.
+  The driver is built such that functionality degrades gracefully
+  nevertheless. See the section on known limitations of the controller.
+
+- No use of hardware CAN ID filtering
+
+  An ELM327's UART sending buffer will easily overflow on heavy CAN bus
+  load, resulting in the "``BUFFER FULL``" message. Using the hardware
+  filters available through "``AT CF xxx``" and "``AT CM xxx``" would be
+  helpful here, however SocketCAN does not currently provide a facility
+  to make use of such hardware features.
+
+
+
+Rationale behind the chosen configuration
+------------------------------------------
+
+``AT E1``
+  Echo on
+
+  We need this to be able to get a prompt reliably.
+
+``AT S1``
+  Spaces on
+
+  We need this to distinguish 11/29 bit CAN addresses received.
+
+  Note:
+  We can usually do this using the line length (odd/even),
+  but this fails if the line is not transmitted fully to
+  the host (BUFFER FULL).
+
+``AT D1``
+  DLC on
+
+  We need this to tell the "length" of RTR frames.
+
+
+
+A note on CAN bus termination
+------------------------------
+
+Your adapter may have resistors soldered in which are meant to terminate
+the bus. This is correct when it is plugged into a OBD-II socket, but
+not helpful when trying to tap into the middle of an existing CAN bus.
+
+If communications don't work with the adapter connected, check for the
+termination resistors on its PCB and try removing them.