Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 459 insertions, 0 deletions

diff --git a/Documentation/networking/device_drivers/ethernet/3com/vortex.rst b/Documentation/networking/device_drivers/ethernet/3com/vortex.rst
new file mode 100644
index 000000000..a060f84c4
--- /dev/null
+++ b/Documentation/networking/device_drivers/ethernet/3com/vortex.rst
@@ -0,0 +1,459 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================
+3Com Vortex device driver
+=========================
+
+Andrew Morton
+
+30 April 2000
+
+
+This document describes the usage and errata of the 3Com "Vortex" device
+driver for Linux, 3c59x.c.
+
+The driver was written by Donald Becker <becker@scyld.com>
+
+Don is no longer the prime maintainer of this version of the driver.
+Please report problems to one or more of:
+
+- Andrew Morton
+- Netdev mailing list <netdev@vger.kernel.org>
+- Linux kernel mailing list <linux-kernel@vger.kernel.org>
+
+Please note the 'Reporting and Diagnosing Problems' section at the end
+of this file.
+
+
+Since kernel 2.3.99-pre6, this driver incorporates the support for the
+3c575-series Cardbus cards which used to be handled by 3c575_cb.c.
+
+This driver supports the following hardware:
+
+	- 3c590 Vortex 10Mbps
+	- 3c592 EISA 10Mbps Demon/Vortex
+	- 3c597 EISA Fast Demon/Vortex
+	- 3c595 Vortex 100baseTx
+	- 3c595 Vortex 100baseT4
+	- 3c595 Vortex 100base-MII
+	- 3c900 Boomerang 10baseT
+	- 3c900 Boomerang 10Mbps Combo
+	- 3c900 Cyclone 10Mbps TPO
+	- 3c900 Cyclone 10Mbps Combo
+	- 3c900 Cyclone 10Mbps TPC
+	- 3c900B-FL Cyclone 10base-FL
+	- 3c905 Boomerang 100baseTx
+	- 3c905 Boomerang 100baseT4
+	- 3c905B Cyclone 100baseTx
+	- 3c905B Cyclone 10/100/BNC
+	- 3c905B-FX Cyclone 100baseFx
+	- 3c905C Tornado
+	- 3c920B-EMB-WNM (ATI Radeon 9100 IGP)
+	- 3c980 Cyclone
+	- 3c980C Python-T
+	- 3cSOHO100-TX Hurricane
+	- 3c555 Laptop Hurricane
+	- 3c556 Laptop Tornado
+	- 3c556B Laptop Hurricane
+	- 3c575 [Megahertz] 10/100 LAN  CardBus
+	- 3c575 Boomerang CardBus
+	- 3CCFE575BT Cyclone CardBus
+	- 3CCFE575CT Tornado CardBus
+	- 3CCFE656 Cyclone CardBus
+	- 3CCFEM656B Cyclone+Winmodem CardBus
+	- 3CXFEM656C Tornado+Winmodem CardBus
+	- 3c450 HomePNA Tornado
+	- 3c920 Tornado
+	- 3c982 Hydra Dual Port A
+	- 3c982 Hydra Dual Port B
+	- 3c905B-T4
+	- 3c920B-EMB-WNM Tornado
+
+Module parameters
+=================
+
+There are several parameters which may be provided to the driver when
+its module is loaded.  These are usually placed in ``/etc/modprobe.d/*.conf``
+configuration files.  Example::
+
+    options 3c59x debug=3 rx_copybreak=300
+
+If you are using the PCMCIA tools (cardmgr) then the options may be
+placed in /etc/pcmcia/config.opts::
+
+    module "3c59x" opts "debug=3 rx_copybreak=300"
+
+
+The supported parameters are:
+
+debug=N
+
+  Where N is a number from 0 to 7.  Anything above 3 produces a lot
+  of output in your system logs.  debug=1 is default.
+
+options=N1,N2,N3,...
+
+  Each number in the list provides an option to the corresponding
+  network card.  So if you have two 3c905's and you wish to provide
+  them with option 0x204 you would use::
+
+    options=0x204,0x204
+
+  The individual options are composed of a number of bitfields which
+  have the following meanings:
+
+  Possible media type settings
+
+	==	=================================
+	0	10baseT
+	1	10Mbs AUI
+	2	undefined
+	3	10base2 (BNC)
+	4	100base-TX
+	5	100base-FX
+	6	MII (Media Independent Interface)
+	7	Use default setting from EEPROM
+	8       Autonegotiate
+	9       External MII
+	10      Use default setting from EEPROM
+	==	=================================
+
+  When generating a value for the 'options' setting, the above media
+  selection values may be OR'ed (or added to) the following:
+
+  ======  =============================================
+  0x8000  Set driver debugging level to 7
+  0x4000  Set driver debugging level to 2
+  0x0400  Enable Wake-on-LAN
+  0x0200  Force full duplex mode.
+  0x0010  Bus-master enable bit (Old Vortex cards only)
+  ======  =============================================
+
+  For example::
+
+    insmod 3c59x options=0x204
+
+  will force full-duplex 100base-TX, rather than allowing the usual
+  autonegotiation.
+
+global_options=N
+
+  Sets the ``options`` parameter for all 3c59x NICs in the machine.
+  Entries in the ``options`` array above will override any setting of
+  this.
+
+full_duplex=N1,N2,N3...
+
+  Similar to bit 9 of 'options'.  Forces the corresponding card into
+  full-duplex mode.  Please use this in preference to the ``options``
+  parameter.
+
+  In fact, please don't use this at all! You're better off getting
+  autonegotiation working properly.
+
+global_full_duplex=N1
+
+  Sets full duplex mode for all 3c59x NICs in the machine.  Entries
+  in the ``full_duplex`` array above will override any setting of this.
+
+flow_ctrl=N1,N2,N3...
+
+  Use 802.3x MAC-layer flow control.  The 3com cards only support the
+  PAUSE command, which means that they will stop sending packets for a
+  short period if they receive a PAUSE frame from the link partner.
+
+  The driver only allows flow control on a link which is operating in
+  full duplex mode.
+
+  This feature does not appear to work on the 3c905 - only 3c905B and
+  3c905C have been tested.
+
+  The 3com cards appear to only respond to PAUSE frames which are
+  sent to the reserved destination address of 01:80:c2:00:00:01.  They
+  do not honour PAUSE frames which are sent to the station MAC address.
+
+rx_copybreak=M
+
+  The driver preallocates 32 full-sized (1536 byte) network buffers
+  for receiving.  When a packet arrives, the driver has to decide
+  whether to leave the packet in its full-sized buffer, or to allocate
+  a smaller buffer and copy the packet across into it.
+
+  This is a speed/space tradeoff.
+
+  The value of rx_copybreak is used to decide when to make the copy.
+  If the packet size is less than rx_copybreak, the packet is copied.
+  The default value for rx_copybreak is 200 bytes.
+
+max_interrupt_work=N
+
+  The driver's interrupt service routine can handle many receive and
+  transmit packets in a single invocation.  It does this in a loop.
+  The value of max_interrupt_work governs how many times the interrupt
+  service routine will loop.  The default value is 32 loops.  If this
+  is exceeded the interrupt service routine gives up and generates a
+  warning message "eth0: Too much work in interrupt".
+
+hw_checksums=N1,N2,N3,...
+
+  Recent 3com NICs are able to generate IPv4, TCP and UDP checksums
+  in hardware.  Linux has used the Rx checksumming for a long time.
+  The "zero copy" patch which is planned for the 2.4 kernel series
+  allows you to make use of the NIC's DMA scatter/gather and transmit
+  checksumming as well.
+
+  The driver is set up so that, when the zerocopy patch is applied,
+  all Tornado and Cyclone devices will use S/G and Tx checksums.
+
+  This module parameter has been provided so you can override this
+  decision.  If you think that Tx checksums are causing a problem, you
+  may disable the feature with ``hw_checksums=0``.
+
+  If you think your NIC should be performing Tx checksumming and the
+  driver isn't enabling it, you can force the use of hardware Tx
+  checksumming with ``hw_checksums=1``.
+
+  The driver drops a message in the logfiles to indicate whether or
+  not it is using hardware scatter/gather and hardware Tx checksums.
+
+  Scatter/gather and hardware checksums provide considerable
+  performance improvement for the sendfile() system call, but a small
+  decrease in throughput for send().  There is no effect upon receive
+  efficiency.
+
+compaq_ioaddr=N,
+compaq_irq=N,
+compaq_device_id=N
+
+  "Variables to work-around the Compaq PCI BIOS32 problem"....
+
+watchdog=N
+
+  Sets the time duration (in milliseconds) after which the kernel
+  decides that the transmitter has become stuck and needs to be reset.
+  This is mainly for debugging purposes, although it may be advantageous
+  to increase this value on LANs which have very high collision rates.
+  The default value is 5000 (5.0 seconds).
+
+enable_wol=N1,N2,N3,...
+
+  Enable Wake-on-LAN support for the relevant interface.  Donald
+  Becker's ``ether-wake`` application may be used to wake suspended
+  machines.
+
+  Also enables the NIC's power management support.
+
+global_enable_wol=N
+
+  Sets enable_wol mode for all 3c59x NICs in the machine.  Entries in
+  the ``enable_wol`` array above will override any setting of this.
+
+Media selection
+---------------
+
+A number of the older NICs such as the 3c590 and 3c900 series have
+10base2 and AUI interfaces.
+
+Prior to January, 2001 this driver would autoselect the 10base2 or AUI
+port if it didn't detect activity on the 10baseT port.  It would then
+get stuck on the 10base2 port and a driver reload was necessary to
+switch back to 10baseT.  This behaviour could not be prevented with a
+module option override.
+
+Later (current) versions of the driver _do_ support locking of the
+media type.  So if you load the driver module with
+
+	modprobe 3c59x options=0
+
+it will permanently select the 10baseT port.  Automatic selection of
+other media types does not occur.
+
+
+Transmit error, Tx status register 82
+-------------------------------------
+
+This is a common error which is almost always caused by another host on
+the same network being in full-duplex mode, while this host is in
+half-duplex mode.  You need to find that other host and make it run in
+half-duplex mode or fix this host to run in full-duplex mode.
+
+As a last resort, you can force the 3c59x driver into full-duplex mode
+with
+
+	options 3c59x full_duplex=1
+
+but this has to be viewed as a workaround for broken network gear and
+should only really be used for equipment which cannot autonegotiate.
+
+
+Additional resources
+--------------------
+
+Details of the device driver implementation are at the top of the source file.
+
+Additional documentation is available at Don Becker's Linux Drivers site:
+
+     http://www.scyld.com/vortex.html
+
+Donald Becker's driver development site:
+
+     http://www.scyld.com/network.html
+
+Donald's vortex-diag program is useful for inspecting the NIC's state:
+
+     http://www.scyld.com/ethercard_diag.html
+
+Donald's mii-diag program may be used for inspecting and manipulating
+the NIC's Media Independent Interface subsystem:
+
+     http://www.scyld.com/ethercard_diag.html#mii-diag
+
+Donald's wake-on-LAN page:
+
+     http://www.scyld.com/wakeonlan.html
+
+3Com's DOS-based application for setting up the NICs EEPROMs:
+
+	ftp://ftp.3com.com/pub/nic/3c90x/3c90xx2.exe
+
+
+Autonegotiation notes
+---------------------
+
+  The driver uses a one-minute heartbeat for adapting to changes in
+  the external LAN environment if link is up and 5 seconds if link is down.
+  This means that when, for example, a machine is unplugged from a hubbed
+  10baseT LAN plugged into a  switched 100baseT LAN, the throughput
+  will be quite dreadful for up to sixty seconds.  Be patient.
+
+  Cisco interoperability note from Walter Wong <wcw+@CMU.EDU>:
+
+  On a side note, adding HAS_NWAY seems to share a problem with the
+  Cisco 6509 switch.  Specifically, you need to change the spanning
+  tree parameter for the port the machine is plugged into to 'portfast'
+  mode.  Otherwise, the negotiation fails.  This has been an issue
+  we've noticed for a while but haven't had the time to track down.
+
+  Cisco switches    (Jeff Busch <jbusch@deja.com>)
+
+    My "standard config" for ports to which PC's/servers connect directly::
+
+	interface FastEthernet0/N
+	description machinename
+	load-interval 30
+	spanning-tree portfast
+
+    If autonegotiation is a problem, you may need to specify "speed
+    100" and "duplex full" as well (or "speed 10" and "duplex half").
+
+    WARNING: DO NOT hook up hubs/switches/bridges to these
+    specially-configured ports! The switch will become very confused.
+
+
+Reporting and diagnosing problems
+---------------------------------
+
+Maintainers find that accurate and complete problem reports are
+invaluable in resolving driver problems.  We are frequently not able to
+reproduce problems and must rely on your patience and efforts to get to
+the bottom of the problem.
+
+If you believe you have a driver problem here are some of the
+steps you should take:
+
+- Is it really a driver problem?
+
+   Eliminate some variables: try different cards, different
+   computers, different cables, different ports on the switch/hub,
+   different versions of the kernel or of the driver, etc.
+
+- OK, it's a driver problem.
+
+   You need to generate a report.  Typically this is an email to the
+   maintainer and/or netdev@vger.kernel.org.  The maintainer's
+   email address will be in the driver source or in the MAINTAINERS file.
+
+- The contents of your report will vary a lot depending upon the
+  problem.  If it's a kernel crash then you should refer to
+  'Documentation/admin-guide/reporting-issues.rst'.
+
+  But for most problems it is useful to provide the following:
+
+   - Kernel version, driver version
+
+   - A copy of the banner message which the driver generates when
+     it is initialised.  For example:
+
+     eth0: 3Com PCI 3c905C Tornado at 0xa400,  00:50:da:6a:88:f0, IRQ 19
+     8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
+     MII transceiver found at address 24, status 782d.
+     Enabling bus-master transmits and whole-frame receives.
+
+     NOTE: You must provide the ``debug=2`` modprobe option to generate
+     a full detection message.  Please do this::
+
+	modprobe 3c59x debug=2
+
+   - If it is a PCI device, the relevant output from 'lspci -vx', eg::
+
+       00:09.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74)
+	       Subsystem: 3Com Corporation: Unknown device 9200
+	       Flags: bus master, medium devsel, latency 32, IRQ 19
+	       I/O ports at a400 [size=128]
+	       Memory at db000000 (32-bit, non-prefetchable) [size=128]
+	       Expansion ROM at <unassigned> [disabled] [size=128K]
+	       Capabilities: [dc] Power Management version 2
+       00: b7 10 00 92 07 00 10 02 74 00 00 02 08 20 00 00
+       10: 01 a4 00 00 00 00 00 db 00 00 00 00 00 00 00 00
+       20: 00 00 00 00 00 00 00 00 00 00 00 00 b7 10 00 10
+       30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 0a 0a
+
+   - A description of the environment: 10baseT? 100baseT?
+     full/half duplex? switched or hubbed?
+
+   - Any additional module parameters which you may be providing to the driver.
+
+   - Any kernel logs which are produced.  The more the merrier.
+     If this is a large file and you are sending your report to a
+     mailing list, mention that you have the logfile, but don't send
+     it.  If you're reporting direct to the maintainer then just send
+     it.
+
+     To ensure that all kernel logs are available, add the
+     following line to /etc/syslog.conf::
+
+	 kern.* /var/log/messages
+
+     Then restart syslogd with::
+
+	 /etc/rc.d/init.d/syslog restart
+
+     (The above may vary, depending upon which Linux distribution you use).
+
+    - If your problem is reproducible then that's great.  Try the
+      following:
+
+      1) Increase the debug level.  Usually this is done via:
+
+	 a) modprobe driver debug=7
+	 b) In /etc/modprobe.d/driver.conf:
+	    options driver debug=7
+
+      2) Recreate the problem with the higher debug level,
+	 send all logs to the maintainer.
+
+      3) Download you card's diagnostic tool from Donald
+	 Becker's website <http://www.scyld.com/ethercard_diag.html>.
+	 Download mii-diag.c as well.  Build these.
+
+	 a) Run 'vortex-diag -aaee' and 'mii-diag -v' when the card is
+	    working correctly.  Save the output.
+
+	 b) Run the above commands when the card is malfunctioning.  Send
+	    both sets of output.
+
+Finally, please be patient and be prepared to do some work.  You may
+end up working on this problem for a week or more as the maintainer
+asks more questions, asks for more tests, asks for patches to be
+applied, etc.  At the end of it all, the problem may even remain
+unresolved.