Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 383 insertions, 0 deletions

diff --git a/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst b/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst
new file mode 100644
index 000000000..f49cd370e
--- /dev/null
+++ b/Documentation/networking/device_drivers/ethernet/intel/e1000e.rst
@@ -0,0 +1,383 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+=====================================================
+Linux Driver for Intel(R) Ethernet Network Connection
+=====================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 2008-2018 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Additional Configurations
+- Support
+
+
+Identifying Your Adapter
+========================
+For information on how to identify your adapter, and for the latest Intel
+network drivers, refer to the Intel Support website:
+https://www.intel.com/support
+
+
+Command Line Parameters
+=======================
+If the driver is built as a module, the following optional parameters are used
+by entering them on the command line with the modprobe command using this
+syntax::
+
+    modprobe e1000e [<option>=<VAL1>,<VAL2>,...]
+
+There needs to be a <VAL#> for each network port in the system supported by
+this driver. The values will be applied to each instance, in function order.
+For example::
+
+    modprobe e1000e InterruptThrottleRate=16000,16000
+
+In this case, there are two network ports supported by e1000e in the system.
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTE: A descriptor describes a data buffer and attributes related to the data
+buffer. This information is accessed by the hardware.
+
+InterruptThrottleRate
+---------------------
+:Valid Range: 0,1,3,4,100-100000
+:Default Value: 3
+
+Interrupt Throttle Rate controls the number of interrupts each interrupt
+vector can generate per second. Increasing ITR lowers latency at the cost of
+increased CPU utilization, though it may help throughput in some circumstances.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The default behaviour of the driver previously assumed a static
+InterruptThrottleRate value of 8000, providing a good fallback value for
+all traffic types, but lacking in small packet performance and latency.
+The hardware can handle many more small packets per second however, and
+for this reason an adaptive interrupt moderation algorithm was implemented.
+
+The driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes.  Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+ - 0: Off
+      Turns off any interrupt moderation and may improve small packet latency.
+      However, this is generally not suitable for bulk throughput traffic due
+      to the increased CPU utilization of the higher interrupt rate.
+ - 1: Dynamic mode
+      This mode attempts to moderate interrupts per vector while maintaining
+      very low latency. This can sometimes cause extra CPU utilization. If
+      planning on deploying e1000e in a latency sensitive environment, this
+      parameter should be considered.
+ - 3: Dynamic Conservative mode (default)
+      In dynamic conservative mode, the InterruptThrottleRate value is set to
+      4000 for traffic that falls in class "Bulk traffic". If traffic falls in
+      the "Low latency" or "Lowest latency" class, the InterruptThrottleRate is
+      increased stepwise to 20000. This default mode is suitable for most
+      applications.
+ - 4: Simplified Balancing mode
+      In simplified mode the interrupt rate is based on the ratio of TX and
+      RX traffic.  If the bytes per second rate is approximately equal, the
+      interrupt rate will drop as low as 2000 interrupts per second.  If the
+      traffic is mostly transmit or mostly receive, the interrupt rate could
+      be as high as 8000.
+ - 100-100000:
+      Setting InterruptThrottleRate to a value greater or equal to 100
+      will program the adapter to send at most that many interrupts per second,
+      even if more packets have come in. This reduces interrupt load on the
+      system and can lower CPU utilization under heavy load, but will increase
+      latency as packets are not processed as quickly.
+
+NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+RxAbsIntDelay parameters. In other words, minimizing the receive and/or
+transmit absolute delays does not force the controller to generate more
+interrupts than what the Interrupt Throttle Rate allows.
+
+RxIntDelay
+----------
+:Valid Range: 0-65535 (0=off)
+:Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds. Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic. Increasing this value adds extra
+latency to frame reception and can end up decreasing the throughput of TCP
+traffic. If the system is reporting dropped receives, this value may be set
+too high, causing the driver to run out of available receive descriptors.
+
+CAUTION: When setting RxIntDelay to a value other than 0, adapters may hang
+(stop transmitting) under certain network conditions. If this occurs a NETDEV
+WATCHDOG message is logged in the system event log. In addition, the
+controller is automatically reset, restoring the network connection. To
+eliminate the potential for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+:Valid Range: 0-65535 (0=off)
+:Default Value: 8
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated. This value ensures that an interrupt is
+generated after the initial packet is received within the set amount of time,
+which is useful only if RxIntDelay is non-zero. Proper tuning, along with
+RxIntDelay, may improve traffic throughput in specific network conditions.
+
+TxIntDelay
+----------
+:Valid Range: 0-65535 (0=off)
+:Default Value: 8
+
+This value delays the generation of transmit interrupts in units of 1.024
+microseconds. Transmit interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic. If the system is reporting
+dropped transmits, this value may be set too high causing the driver to run
+out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+:Valid Range: 0-65535 (0=off)
+:Default Value: 32
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated. It is useful only if TxIntDelay is non-zero.
+It ensures that an interrupt is generated after the initial Packet is sent on
+the wire within the set amount of time. Proper tuning, along with TxIntDelay,
+may improve traffic throughput in specific network conditions.
+
+copybreak
+---------
+:Valid Range: 0-xxxxxxx (0=off)
+:Default Value: 256
+
+The driver copies all packets below or equaling this size to a fresh receive
+buffer before handing it up the stack.
+This parameter differs from other parameters because it is a single (not 1,1,1
+etc.) parameter applied to all driver instances and it is also available
+during runtime at /sys/module/e1000e/parameters/copybreak.
+
+To use copybreak, type::
+
+    modprobe e1000e.ko copybreak=128
+
+SmartPowerDownEnable
+--------------------
+:Valid Range: 0,1
+:Default Value: 0 (disabled)
+
+Allows the PHY to turn off in lower power states. The user can turn off this
+parameter in supported chipsets.
+
+KumeranLockLoss
+---------------
+:Valid Range: 0,1
+:Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial silicon
+releases of ICH8 systems.
+
+IntMode
+-------
+:Valid Range: 0-2
+:Default Value: 0
+
+   +-------+----------------+
+   | Value | Interrupt Mode |
+   +=======+================+
+   |   0   |     Legacy     |
+   +-------+----------------+
+   |   1   |       MSI      |
+   +-------+----------------+
+   |   2   |      MSI-X     |
+   +-------+----------------+
+
+IntMode allows load time control over the type of interrupt registered for by
+the driver. MSI-X is required for multiple queue support, and some kernels and
+combinations of kernel .config options will force a lower level of interrupt
+support.
+
+This command will show different values for each type of interrupt::
+
+  cat /proc/interrupts
+
+CrcStripping
+------------
+:Valid Range: 0,1
+:Default Value: 1 (enabled)
+
+Strip the CRC from received packets before sending up the network stack. If
+you have a machine with a BMC enabled but cannot receive IPMI traffic after
+loading or enabling the driver, try disabling this feature.
+
+WriteProtectNVM
+---------------
+:Valid Range: 0,1
+:Default Value: 1 (enabled)
+
+If set to 1, configure the hardware to ignore all write/erase cycles to the
+GbE region in the ICHx NVM (in order to prevent accidental corruption of the
+NVM). This feature can be disabled by setting the parameter to 0 during initial
+driver load.
+
+NOTE: The machine must be power cycled (full off/on) when enabling NVM writes
+via setting the parameter to zero. Once the NVM has been locked (via the
+parameter at 1 when the driver loads) it cannot be unlocked except via power
+cycle.
+
+Debug
+-----
+:Valid Range: 0-16 (0=none,...,16=all)
+:Default Value: 0
+
+This parameter adjusts the level of debug messages displayed in the system logs.
+
+
+Additional Features and Configurations
+======================================
+
+Jumbo Frames
+------------
+Jumbo Frames support is enabled by changing the Maximum Transmission Unit (MTU)
+to a value larger than the default value of 1500.
+
+Use the ifconfig command to increase the MTU size. For example, enter the
+following where <x> is the interface number::
+
+    ifconfig eth<x> mtu 9000 up
+
+Alternatively, you can use the ip command as follows::
+
+    ip link set mtu 9000 dev eth<x>
+    ip link set up dev eth<x>
+
+This setting is not saved across reboots. The setting change can be made
+permanent by adding 'MTU=9000' to the file:
+
+- For RHEL: /etc/sysconfig/network-scripts/ifcfg-eth<x>
+- For SLES: /etc/sysconfig/network/<config_file>
+
+NOTE: The maximum MTU setting for Jumbo Frames is 8996. This value coincides
+with the maximum Jumbo Frames size of 9018 bytes.
+
+NOTE: Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
+poor performance or loss of link.
+
+NOTE: The following adapters limit Jumbo Frames sized packets to a maximum of
+4088 bytes:
+
+  - Intel(R) 82578DM Gigabit Network Connection
+  - Intel(R) 82577LM Gigabit Network Connection
+
+The following adapters do not support Jumbo Frames:
+
+  - Intel(R) PRO/1000 Gigabit Server Adapter
+  - Intel(R) PRO/1000 PM Network Connection
+  - Intel(R) 82562G 10/100 Network Connection
+  - Intel(R) 82562G-2 10/100 Network Connection
+  - Intel(R) 82562GT 10/100 Network Connection
+  - Intel(R) 82562GT-2 10/100 Network Connection
+  - Intel(R) 82562V 10/100 Network Connection
+  - Intel(R) 82562V-2 10/100 Network Connection
+  - Intel(R) 82566DC Gigabit Network Connection
+  - Intel(R) 82566DC-2 Gigabit Network Connection
+  - Intel(R) 82566DM Gigabit Network Connection
+  - Intel(R) 82566MC Gigabit Network Connection
+  - Intel(R) 82566MM Gigabit Network Connection
+  - Intel(R) 82567V-3 Gigabit Network Connection
+  - Intel(R) 82577LC Gigabit Network Connection
+  - Intel(R) 82578DC Gigabit Network Connection
+
+NOTE: Jumbo Frames cannot be configured on an 82579-based Network device if
+MACSec is enabled on the system.
+
+
+ethtool
+-------
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information. The latest ethtool
+version is required for this functionality. Download it at:
+
+https://www.kernel.org/pub/software/network/ethtool/
+
+NOTE: When validating enable/disable tests on some parts (for example, 82578),
+it is necessary to add a few seconds between tests when working with ethtool.
+
+
+Speed and Duplex Configuration
+------------------------------
+In addressing speed and duplex configuration issues, you need to distinguish
+between copper-based adapters and fiber-based adapters.
+
+In the default mode, an Intel(R) Ethernet Network Adapter using copper
+connections will attempt to auto-negotiate with its link partner to determine
+the best setting. If the adapter cannot establish link with the link partner
+using auto-negotiation, you may need to manually configure the adapter and link
+partner to identical settings to establish link and pass packets. This should
+only be needed when attempting to link with an older switch that does not
+support auto-negotiation or one that has been forced to a specific speed or
+duplex mode. Your link partner must match the setting you choose. 1 Gbps speeds
+and higher cannot be forced. Use the autonegotiation advertising setting to
+manually set devices for 1 Gbps and higher.
+
+Speed, duplex, and autonegotiation advertising are configured through the
+ethtool utility.
+
+Caution: Only experienced network administrators should force speed and duplex
+or change autonegotiation advertising manually. The settings at the switch must
+always match the adapter settings. Adapter performance may suffer or your
+adapter may not operate if you configure the adapter differently from your
+switch.
+
+An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
+will not attempt to auto-negotiate with its link partner since those adapters
+operate only in full duplex and only at their native speed.
+
+
+Enabling Wake on LAN (WoL)
+--------------------------
+WoL is configured through the ethtool utility.
+
+WoL will be enabled on the system during the next shut down or reboot. For
+this driver version, in order to enable WoL, the e1000e driver must be loaded
+prior to shutting down or suspending the system.
+
+NOTE: Wake on LAN is only supported on port A for the following devices:
+- Intel(R) PRO/1000 PT Dual Port Network Connection
+- Intel(R) PRO/1000 PT Dual Port Server Connection
+- Intel(R) PRO/1000 PT Dual Port Server Adapter
+- Intel(R) PRO/1000 PF Dual Port Server Adapter
+- Intel(R) PRO/1000 PT Quad Port Server Adapter
+- Intel(R) Gigabit PT Quad Port Server ExpressModule
+
+
+Support
+=======
+For general information, go to the Intel support website at:
+
+https://www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+https://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on a supported kernel
+with a supported adapter, email the specific information related to the issue
+to e1000-devel@lists.sf.net.