Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 530 insertions, 0 deletions

diff --git a/Documentation/s390/cds.rst b/Documentation/s390/cds.rst
new file mode 100644
index 000000000..7006d8209
--- /dev/null
+++ b/Documentation/s390/cds.rst
@@ -0,0 +1,530 @@
+===========================
+Linux for S/390 and zSeries
+===========================
+
+Common Device Support (CDS)
+Device Driver I/O Support Routines
+
+Authors:
+	- Ingo Adlung
+	- Cornelia Huck
+
+Copyright, IBM Corp. 1999-2002
+
+Introduction
+============
+
+This document describes the common device support routines for Linux/390.
+Different than other hardware architectures, ESA/390 has defined a unified
+I/O access method. This gives relief to the device drivers as they don't
+have to deal with different bus types, polling versus interrupt
+processing, shared versus non-shared interrupt processing, DMA versus port
+I/O (PIO), and other hardware features more. However, this implies that
+either every single device driver needs to implement the hardware I/O
+attachment functionality itself, or the operating system provides for a
+unified method to access the hardware, providing all the functionality that
+every single device driver would have to provide itself.
+
+The document does not intend to explain the ESA/390 hardware architecture in
+every detail.This information can be obtained from the ESA/390 Principles of
+Operation manual (IBM Form. No. SA22-7201).
+
+In order to build common device support for ESA/390 I/O interfaces, a
+functional layer was introduced that provides generic I/O access methods to
+the hardware.
+
+The common device support layer comprises the I/O support routines defined
+below. Some of them implement common Linux device driver interfaces, while
+some of them are ESA/390 platform specific.
+
+Note:
+  In order to write a driver for S/390, you also need to look into the interface
+  described in Documentation/s390/driver-model.rst.
+
+Note for porting drivers from 2.4:
+
+The major changes are:
+
+* The functions use a ccw_device instead of an irq (subchannel).
+* All drivers must define a ccw_driver (see driver-model.txt) and the associated
+  functions.
+* request_irq() and free_irq() are no longer done by the driver.
+* The oper_handler is (kindof) replaced by the probe() and set_online() functions
+  of the ccw_driver.
+* The not_oper_handler is (kindof) replaced by the remove() and set_offline()
+  functions of the ccw_driver.
+* The channel device layer is gone.
+* The interrupt handlers must be adapted to use a ccw_device as argument.
+  Moreover, they don't return a devstat, but an irb.
+* Before initiating an io, the options must be set via ccw_device_set_options().
+* Instead of calling read_dev_chars()/read_conf_data(), the driver issues
+  the channel program and handles the interrupt itself.
+
+ccw_device_get_ciw()
+   get commands from extended sense data.
+
+ccw_device_start(), ccw_device_start_timeout(), ccw_device_start_key(), ccw_device_start_key_timeout()
+   initiate an I/O request.
+
+ccw_device_resume()
+   resume channel program execution.
+
+ccw_device_halt()
+   terminate the current I/O request processed on the device.
+
+do_IRQ()
+   generic interrupt routine. This function is called by the interrupt entry
+   routine whenever an I/O interrupt is presented to the system. The do_IRQ()
+   routine determines the interrupt status and calls the device specific
+   interrupt handler according to the rules (flags) defined during I/O request
+   initiation with do_IO().
+
+The next chapters describe the functions other than do_IRQ() in more details.
+The do_IRQ() interface is not described, as it is called from the Linux/390
+first level interrupt handler only and does not comprise a device driver
+callable interface. Instead, the functional description of do_IO() also
+describes the input to the device specific interrupt handler.
+
+Note:
+	All explanations apply also to the 64 bit architecture s390x.
+
+
+Common Device Support (CDS) for Linux/390 Device Drivers
+========================================================
+
+General Information
+-------------------
+
+The following chapters describe the I/O related interface routines the
+Linux/390 common device support (CDS) provides to allow for device specific
+driver implementations on the IBM ESA/390 hardware platform. Those interfaces
+intend to provide the functionality required by every device driver
+implementation to allow to drive a specific hardware device on the ESA/390
+platform. Some of the interface routines are specific to Linux/390 and some
+of them can be found on other Linux platforms implementations too.
+Miscellaneous function prototypes, data declarations, and macro definitions
+can be found in the architecture specific C header file
+linux/arch/s390/include/asm/irq.h.
+
+Overview of CDS interface concepts
+----------------------------------
+
+Different to other hardware platforms, the ESA/390 architecture doesn't define
+interrupt lines managed by a specific interrupt controller and bus systems
+that may or may not allow for shared interrupts, DMA processing, etc.. Instead,
+the ESA/390 architecture has implemented a so called channel subsystem, that
+provides a unified view of the devices physically attached to the systems.
+Though the ESA/390 hardware platform knows about a huge variety of different
+peripheral attachments like disk devices (aka. DASDs), tapes, communication
+controllers, etc. they can all be accessed by a well defined access method and
+they are presenting I/O completion a unified way : I/O interruptions. Every
+single device is uniquely identified to the system by a so called subchannel,
+where the ESA/390 architecture allows for 64k devices be attached.
+
+Linux, however, was first built on the Intel PC architecture, with its two
+cascaded 8259 programmable interrupt controllers (PICs), that allow for a
+maximum of 15 different interrupt lines. All devices attached to such a system
+share those 15 interrupt levels. Devices attached to the ISA bus system must
+not share interrupt levels (aka. IRQs), as the ISA bus bases on edge triggered
+interrupts. MCA, EISA, PCI and other bus systems base on level triggered
+interrupts, and therewith allow for shared IRQs. However, if multiple devices
+present their hardware status by the same (shared) IRQ, the operating system
+has to call every single device driver registered on this IRQ in order to
+determine the device driver owning the device that raised the interrupt.
+
+Up to kernel 2.4, Linux/390 used to provide interfaces via the IRQ (subchannel).
+For internal use of the common I/O layer, these are still there. However,
+device drivers should use the new calling interface via the ccw_device only.
+
+During its startup the Linux/390 system checks for peripheral devices. Each
+of those devices is uniquely defined by a so called subchannel by the ESA/390
+channel subsystem. While the subchannel numbers are system generated, each
+subchannel also takes a user defined attribute, the so called device number.
+Both subchannel number and device number cannot exceed 65535. During sysfs
+initialisation, the information about control unit type and device types that
+imply specific I/O commands (channel command words - CCWs) in order to operate
+the device are gathered. Device drivers can retrieve this set of hardware
+information during their initialization step to recognize the devices they
+support using the information saved in the struct ccw_device given to them.
+This methods implies that Linux/390 doesn't require to probe for free (not
+armed) interrupt request lines (IRQs) to drive its devices with. Where
+applicable, the device drivers can use issue the READ DEVICE CHARACTERISTICS
+ccw to retrieve device characteristics in its online routine.
+
+In order to allow for easy I/O initiation the CDS layer provides a
+ccw_device_start() interface that takes a device specific channel program (one
+or more CCWs) as input sets up the required architecture specific control blocks
+and initiates an I/O request on behalf of the device driver. The
+ccw_device_start() routine allows to specify whether it expects the CDS layer
+to notify the device driver for every interrupt it observes, or with final status
+only. See ccw_device_start() for more details. A device driver must never issue
+ESA/390 I/O commands itself, but must use the Linux/390 CDS interfaces instead.
+
+For long running I/O request to be canceled, the CDS layer provides the
+ccw_device_halt() function. Some devices require to initially issue a HALT
+SUBCHANNEL (HSCH) command without having pending I/O requests. This function is
+also covered by ccw_device_halt().
+
+
+get_ciw() - get command information word
+
+This call enables a device driver to get information about supported commands
+from the extended SenseID data.
+
+::
+
+  struct ciw *
+  ccw_device_get_ciw(struct ccw_device *cdev, __u32 cmd);
+
+====  ========================================================
+cdev  The ccw_device for which the command is to be retrieved.
+cmd   The command type to be retrieved.
+====  ========================================================
+
+ccw_device_get_ciw() returns:
+
+=====  ================================================================
+ NULL  No extended data available, invalid device or command not found.
+!NULL  The command requested.
+=====  ================================================================
+
+::
+
+  ccw_device_start() - Initiate I/O Request
+
+The ccw_device_start() routines is the I/O request front-end processor. All
+device driver I/O requests must be issued using this routine. A device driver
+must not issue ESA/390 I/O commands itself. Instead the ccw_device_start()
+routine provides all interfaces required to drive arbitrary devices.
+
+This description also covers the status information passed to the device
+driver's interrupt handler as this is related to the rules (flags) defined
+with the associated I/O request when calling ccw_device_start().
+
+::
+
+  int ccw_device_start(struct ccw_device *cdev,
+		       struct ccw1 *cpa,
+		       unsigned long intparm,
+		       __u8 lpm,
+		       unsigned long flags);
+  int ccw_device_start_timeout(struct ccw_device *cdev,
+			       struct ccw1 *cpa,
+			       unsigned long intparm,
+			       __u8 lpm,
+			       unsigned long flags,
+			       int expires);
+  int ccw_device_start_key(struct ccw_device *cdev,
+			   struct ccw1 *cpa,
+			   unsigned long intparm,
+			   __u8 lpm,
+			   __u8 key,
+			   unsigned long flags);
+  int ccw_device_start_key_timeout(struct ccw_device *cdev,
+				   struct ccw1 *cpa,
+				   unsigned long intparm,
+				   __u8 lpm,
+				   __u8 key,
+				   unsigned long flags,
+				   int expires);
+
+============= =============================================================
+cdev          ccw_device the I/O is destined for
+cpa           logical start address of channel program
+user_intparm  user specific interrupt information; will be presented
+	      back to the device driver's interrupt handler. Allows a
+	      device driver to associate the interrupt with a
+	      particular I/O request.
+lpm           defines the channel path to be used for a specific I/O
+	      request. A value of 0 will make cio use the opm.
+key           the storage key to use for the I/O (useful for operating on a
+	      storage with a storage key != default key)
+flag          defines the action to be performed for I/O processing
+expires       timeout value in jiffies. The common I/O layer will terminate
+	      the running program after this and call the interrupt handler
+	      with ERR_PTR(-ETIMEDOUT) as irb.
+============= =============================================================
+
+Possible flag values are:
+
+========================= =============================================
+DOIO_ALLOW_SUSPEND        channel program may become suspended
+DOIO_DENY_PREFETCH        don't allow for CCW prefetch; usually
+			  this implies the channel program might
+			  become modified
+DOIO_SUPPRESS_INTER       don't call the handler on intermediate status
+========================= =============================================
+
+The cpa parameter points to the first format 1 CCW of a channel program::
+
+  struct ccw1 {
+	__u8  cmd_code;/* command code */
+	__u8  flags;   /* flags, like IDA addressing, etc. */
+	__u16 count;   /* byte count */
+	__u32 cda;     /* data address */
+  } __attribute__ ((packed,aligned(8)));
+
+with the following CCW flags values defined:
+
+=================== =========================
+CCW_FLAG_DC         data chaining
+CCW_FLAG_CC         command chaining
+CCW_FLAG_SLI        suppress incorrect length
+CCW_FLAG_SKIP       skip
+CCW_FLAG_PCI        PCI
+CCW_FLAG_IDA        indirect addressing
+CCW_FLAG_SUSPEND    suspend
+=================== =========================
+
+
+Via ccw_device_set_options(), the device driver may specify the following
+options for the device:
+
+========================= ======================================
+DOIO_EARLY_NOTIFICATION   allow for early interrupt notification
+DOIO_REPORT_ALL           report all interrupt conditions
+========================= ======================================
+
+
+The ccw_device_start() function returns:
+
+======== ======================================================================
+      0  successful completion or request successfully initiated
+ -EBUSY  The device is currently processing a previous I/O request, or there is
+	 a status pending at the device.
+-ENODEV  cdev is invalid, the device is not operational or the ccw_device is
+	 not online.
+======== ======================================================================
+
+When the I/O request completes, the CDS first level interrupt handler will
+accumulate the status in a struct irb and then call the device interrupt handler.
+The intparm field will contain the value the device driver has associated with a
+particular I/O request. If a pending device status was recognized,
+intparm will be set to 0 (zero). This may happen during I/O initiation or delayed
+by an alert status notification. In any case this status is not related to the
+current (last) I/O request. In case of a delayed status notification no special
+interrupt will be presented to indicate I/O completion as the I/O request was
+never started, even though ccw_device_start() returned with successful completion.
+
+The irb may contain an error value, and the device driver should check for this
+first:
+
+========== =================================================================
+-ETIMEDOUT the common I/O layer terminated the request after the specified
+	   timeout value
+-EIO       the common I/O layer terminated the request due to an error state
+========== =================================================================
+
+If the concurrent sense flag in the extended status word (esw) in the irb is
+set, the field erw.scnt in the esw describes the number of device specific
+sense bytes available in the extended control word irb->scsw.ecw[]. No device
+sensing by the device driver itself is required.
+
+The device interrupt handler can use the following definitions to investigate
+the primary unit check source coded in sense byte 0 :
+
+======================= ====
+SNS0_CMD_REJECT         0x80
+SNS0_INTERVENTION_REQ   0x40
+SNS0_BUS_OUT_CHECK      0x20
+SNS0_EQUIPMENT_CHECK    0x10
+SNS0_DATA_CHECK         0x08
+SNS0_OVERRUN            0x04
+SNS0_INCOMPL_DOMAIN     0x01
+======================= ====
+
+Depending on the device status, multiple of those values may be set together.
+Please refer to the device specific documentation for details.
+
+The irb->scsw.cstat field provides the (accumulated) subchannel status :
+
+========================= ============================
+SCHN_STAT_PCI             program controlled interrupt
+SCHN_STAT_INCORR_LEN      incorrect length
+SCHN_STAT_PROG_CHECK      program check
+SCHN_STAT_PROT_CHECK      protection check
+SCHN_STAT_CHN_DATA_CHK    channel data check
+SCHN_STAT_CHN_CTRL_CHK    channel control check
+SCHN_STAT_INTF_CTRL_CHK   interface control check
+SCHN_STAT_CHAIN_CHECK     chaining check
+========================= ============================
+
+The irb->scsw.dstat field provides the (accumulated) device status :
+
+===================== =================
+DEV_STAT_ATTENTION    attention
+DEV_STAT_STAT_MOD     status modifier
+DEV_STAT_CU_END       control unit end
+DEV_STAT_BUSY         busy
+DEV_STAT_CHN_END      channel end
+DEV_STAT_DEV_END      device end
+DEV_STAT_UNIT_CHECK   unit check
+DEV_STAT_UNIT_EXCEP   unit exception
+===================== =================
+
+Please see the ESA/390 Principles of Operation manual for details on the
+individual flag meanings.
+
+Usage Notes:
+
+ccw_device_start() must be called disabled and with the ccw device lock held.
+
+The device driver is allowed to issue the next ccw_device_start() call from
+within its interrupt handler already. It is not required to schedule a
+bottom-half, unless a non deterministically long running error recovery procedure
+or similar needs to be scheduled. During I/O processing the Linux/390 generic
+I/O device driver support has already obtained the IRQ lock, i.e. the handler
+must not try to obtain it again when calling ccw_device_start() or we end in a
+deadlock situation!
+
+If a device driver relies on an I/O request to be completed prior to start the
+next it can reduce I/O processing overhead by chaining a NoOp I/O command
+CCW_CMD_NOOP to the end of the submitted CCW chain. This will force Channel-End
+and Device-End status to be presented together, with a single interrupt.
+However, this should be used with care as it implies the channel will remain
+busy, not being able to process I/O requests for other devices on the same
+channel. Therefore e.g. read commands should never use this technique, as the
+result will be presented by a single interrupt anyway.
+
+In order to minimize I/O overhead, a device driver should use the
+DOIO_REPORT_ALL  only if the device can report intermediate interrupt
+information prior to device-end the device driver urgently relies on. In this
+case all I/O interruptions are presented to the device driver until final
+status is recognized.
+
+If a device is able to recover from asynchronously presented I/O errors, it can
+perform overlapping I/O using the DOIO_EARLY_NOTIFICATION flag. While some
+devices always report channel-end and device-end together, with a single
+interrupt, others present primary status (channel-end) when the channel is
+ready for the next I/O request and secondary status (device-end) when the data
+transmission has been completed at the device.
+
+Above flag allows to exploit this feature, e.g. for communication devices that
+can handle lost data on the network to allow for enhanced I/O processing.
+
+Unless the channel subsystem at any time presents a secondary status interrupt,
+exploiting this feature will cause only primary status interrupts to be
+presented to the device driver while overlapping I/O is performed. When a
+secondary status without error (alert status) is presented, this indicates
+successful completion for all overlapping ccw_device_start() requests that have
+been issued since the last secondary (final) status.
+
+Channel programs that intend to set the suspend flag on a channel command word
+(CCW)  must start the I/O operation with the DOIO_ALLOW_SUSPEND option or the
+suspend flag will cause a channel program check. At the time the channel program
+becomes suspended an intermediate interrupt will be generated by the channel
+subsystem.
+
+ccw_device_resume() - Resume Channel Program Execution
+
+If a device driver chooses to suspend the current channel program execution by
+setting the CCW suspend flag on a particular CCW, the channel program execution
+is suspended. In order to resume channel program execution the CIO layer
+provides the ccw_device_resume() routine.
+
+::
+
+  int ccw_device_resume(struct ccw_device *cdev);
+
+====  ================================================
+cdev  ccw_device the resume operation is requested for
+====  ================================================
+
+The ccw_device_resume() function returns:
+
+=========   ==============================================
+	0   suspended channel program is resumed
+   -EBUSY   status pending
+  -ENODEV   cdev invalid or not-operational subchannel
+  -EINVAL   resume function not applicable
+-ENOTCONN   there is no I/O request pending for completion
+=========   ==============================================
+
+Usage Notes:
+
+Please have a look at the ccw_device_start() usage notes for more details on
+suspended channel programs.
+
+ccw_device_halt() - Halt I/O Request Processing
+
+Sometimes a device driver might need a possibility to stop the processing of
+a long-running channel program or the device might require to initially issue
+a halt subchannel (HSCH) I/O command. For those purposes the ccw_device_halt()
+command is provided.
+
+ccw_device_halt() must be called disabled and with the ccw device lock held.
+
+::
+
+  int ccw_device_halt(struct ccw_device *cdev,
+		      unsigned long intparm);
+
+=======  =====================================================
+cdev     ccw_device the halt operation is requested for
+intparm  interruption parameter; value is only used if no I/O
+	 is outstanding, otherwise the intparm associated with
+	 the I/O request is returned
+=======  =====================================================
+
+The ccw_device_halt() function returns:
+
+=======  ==============================================================
+      0  request successfully initiated
+-EBUSY   the device is currently busy, or status pending.
+-ENODEV  cdev invalid.
+-EINVAL  The device is not operational or the ccw device is not online.
+=======  ==============================================================
+
+Usage Notes:
+
+A device driver may write a never-ending channel program by writing a channel
+program that at its end loops back to its beginning by means of a transfer in
+channel (TIC)   command (CCW_CMD_TIC). Usually this is performed by network
+device drivers by setting the PCI CCW flag (CCW_FLAG_PCI). Once this CCW is
+executed a program controlled interrupt (PCI) is generated. The device driver
+can then perform an appropriate action. Prior to interrupt of an outstanding
+read to a network device (with or without PCI flag) a ccw_device_halt()
+is required to end the pending operation.
+
+::
+
+  ccw_device_clear() - Terminage I/O Request Processing
+
+In order to terminate all I/O processing at the subchannel, the clear subchannel
+(CSCH) command is used. It can be issued via ccw_device_clear().
+
+ccw_device_clear() must be called disabled and with the ccw device lock held.
+
+::
+
+  int ccw_device_clear(struct ccw_device *cdev, unsigned long intparm);
+
+======= ===============================================
+cdev    ccw_device the clear operation is requested for
+intparm interruption parameter (see ccw_device_halt())
+======= ===============================================
+
+The ccw_device_clear() function returns:
+
+=======  ==============================================================
+      0  request successfully initiated
+-ENODEV  cdev invalid
+-EINVAL  The device is not operational or the ccw device is not online.
+=======  ==============================================================
+
+Miscellaneous Support Routines
+------------------------------
+
+This chapter describes various routines to be used in a Linux/390 device
+driver programming environment.
+
+get_ccwdev_lock()
+
+Get the address of the device specific lock. This is then used in
+spin_lock() / spin_unlock() calls.
+
+::
+
+  __u8 ccw_device_get_path_mask(struct ccw_device *cdev);
+
+Get the mask of the path currently available for cdev.