Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 711 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
new file mode 100644
index 000000000..7956b151c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
@@ -0,0 +1,711 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
+ * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/*
+ * Delete following upstream (msm8998.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &adsp_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &mba_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &wlan_msa_mem;
+
+/ {
+	model = "Xiaomi Mi 6";
+	compatible = "xiaomi,sagit", "qcom,msm8998";
+	chassis-type = "handset";
+	/* Required for bootloader to select correct board */
+	qcom,board-id = <30 0>;
+
+	reserved-memory {
+		/*
+		 * Xiaomi's ADSP firmware requires 30 MiB in total, so increase the adsp_mem
+		 * region by 4 MiB to account for this while relocating the other now
+		 * conflicting memory nodes accordingly.
+		 */
+		adsp_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x1e00000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8d000000 {
+			reg = <0x0 0x8d000000 0x0 0x7000000>;
+			no-map;
+		};
+
+		venus_mem: memory@94000000 {
+			reg = <0x0 0x94000000 0x0 0x500000>;
+			no-map;
+		};
+
+		mba_mem: memory@94500000 {
+			reg = <0x0 0x94500000 0x0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@94700000 {
+			reg = <0x0 0x94700000 0x0 0xf00000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@95600000 {
+			reg = <0x0 0x95600000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@95610000 {
+			reg = <0x0 0x95610000 0x0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: memory@95615000 {
+			reg = <0x0 0x95615000 0x0 0x100000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@95715000 {
+			reg = <0x0 0x95715000 0x0 0x100000>;
+			no-map;
+		};
+
+		/* Bootloader display framebuffer region */
+		cont_splash_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2400000>;
+			no-map;
+		};
+
+		/* For getting crash logs using Android downstream kernels */
+		ramoops@ac000000 {
+			compatible = "ramoops";
+			reg = <0x0 0xac000000 0x0 0x200000>;
+			console-size = <0x80000>;
+			pmsg-size = <0x40000>;
+			record-size = <0x8000>;
+			ftrace-size = <0x20000>;
+		};
+
+		/*
+		 * The following memory regions on downstream are "dynamically allocated"
+		 * but given the same addresses every time. Hard code them as these addresses
+		 * are where the Xiaomi signed firmware expects them to be.
+		 */
+		ipa_fws_region: memory@f7800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7800000 0x0 0x5000>;
+			no-map;
+		};
+
+		zap_shader_region: memory@f7900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7900000 0x0 0x2000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "Volume buttons";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_key_default>;
+
+		key-vol-up {
+			label = "Volume up";
+			gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+		label = "Hall effect sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor_default_state>;
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	disp_vddts_vreg: disp-vddts-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "disp-vddts-regulator";
+		gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_i2c5 {
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_active_state>;
+		pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
+
+		vdd-supply = <&disp_vddts_vreg>;
+		vio-supply = <&vreg_l6a_1p8>;
+
+		syna,reset-delay-ms = <20>;
+		syna,startup-delay-ms = <20>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <64>;
+			touchscreen-y-mm = <114>;
+			syna,sensor-type = <1>;
+			syna,rezero-wait-ms = <20>;
+		};
+
+		rmi4-f1a@1a {
+			reg = <0x1a>;
+			syna,codes = <KEY_BACK KEY_APPSELECT>;
+		};
+	};
+};
+
+&blsp1_i2c5_sleep {
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&blsp1_uart3_on {
+	rx-pins {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 46 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts-pins {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&pm8005_regulators {
+	compatible = "qcom,pm8005-regulators";
+
+	vdd_s1-supply = <&vph_pwr>;
+
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+
+		/* hack until we rig up the gpu consumer */
+		regulator-always-on;
+	};
+};
+
+&pm8998_gpios {
+	vol_up_key_default: vol-up-key-default-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	audio_mclk_pin: audio-mclk-pin-active-state {
+		pins = "gpio13";
+		function = "func2";
+		power-source = <0>;
+	};
+};
+
+&qusb2phy {
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p8: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 { };
+
+		vreg_lvs2a_1p8: lvs2 { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	cci1_default_state: cci1-default-state {
+		pins = "gpio19", "gpio20";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cdc_reset_n_state: cdc-reset-n-state {
+		pins = "gpio64";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <16>;
+		output-high;
+	};
+
+	hall_sensor_default_state: hall-sensor-default-state {
+		pins = "gpio124";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	mdss_dsi_active_state: mdss-dsi-active-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_active_state: mdss-te-active-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_suspend_state: mdss-te-suspend-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk0_active_state: msm-mclk0-active-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk1_active_state: msm-mclk1-active-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_int_active_state: nfc-int-active-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_int_suspend_state: nfc-int-suspend-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_active_state: nfc-enable-active-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_suspend_state: nfc-enable-suspend-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	ts_active_state: ts-active-state {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	ts_int_suspend_state: ts-int-suspend-state {
+		pins = "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ts_reset_suspend_state: ts-reset-suspend-state {
+		pins = "gpio89";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_int_n_state: wcd-int-n-state {
+		pins = "gpio54";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
+		pins = "gpio65";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
+	wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+};
+
+&pm8998_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&ufshc {
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
+	status = "okay";
+};
+
+&ufsphy {
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+	status = "okay";
+};
+
+&usb3 {
+	/* Disable USB3 clock requirement as the device only supports USB2 */
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	/* Drop the unused USB 3 PHY */
+	phys = <&qusb2phy>;
+	phy-names = "usb2-phy";
+
+	/* Fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Force to peripheral until we can switch modes */
+	dr_mode = "peripheral";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	status = "okay";
+};