Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

9 files changed, 844 insertions, 0 deletions

diff --git a/arch/mips/loongson2ef/lemote-2f/Makefile b/arch/mips/loongson2ef/lemote-2f/Makefile
new file mode 100644
index 000000000..881a0ec06
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for lemote loongson2f family machines
+#
+
+obj-y += clock.o machtype.o irq.o reset.o dma.o ec_kb3310b.o
+
+#
+# Suspend Support
+#
+
+obj-$(CONFIG_SUSPEND) += pm.o
diff --git a/arch/mips/loongson2ef/lemote-2f/clock.c b/arch/mips/loongson2ef/lemote-2f/clock.c
new file mode 100644
index 000000000..850b6b9f8
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/clock.c
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2006 - 2008 Lemote Inc. & Institute of Computing Technology
+ * Author: Yanhua, yanh@lemote.com
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/cpufreq.h>
+#include <linux/errno.h>
+#include <linux/export.h>
+
+#include <asm/mach-loongson2ef/loongson.h>
+
+enum {
+	DC_ZERO, DC_25PT = 2, DC_37PT, DC_50PT, DC_62PT, DC_75PT,
+	DC_87PT, DC_DISABLE, DC_RESV
+};
+
+struct cpufreq_frequency_table loongson2_clockmod_table[] = {
+	{0, DC_RESV, CPUFREQ_ENTRY_INVALID},
+	{0, DC_ZERO, CPUFREQ_ENTRY_INVALID},
+	{0, DC_25PT, 0},
+	{0, DC_37PT, 0},
+	{0, DC_50PT, 0},
+	{0, DC_62PT, 0},
+	{0, DC_75PT, 0},
+	{0, DC_87PT, 0},
+	{0, DC_DISABLE, 0},
+	{0, DC_RESV, CPUFREQ_TABLE_END},
+};
+EXPORT_SYMBOL_GPL(loongson2_clockmod_table);
+
+int loongson2_cpu_set_rate(unsigned long rate_khz)
+{
+	struct cpufreq_frequency_table *pos;
+	int regval;
+
+	cpufreq_for_each_valid_entry(pos, loongson2_clockmod_table)
+		if (rate_khz == pos->frequency)
+			break;
+	if (rate_khz != pos->frequency)
+		return -ENOTSUPP;
+
+	regval = readl(LOONGSON_CHIPCFG);
+	regval = (regval & ~0x7) | (pos->driver_data - 1);
+	writel(regval, LOONGSON_CHIPCFG);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(loongson2_cpu_set_rate);
diff --git a/arch/mips/loongson2ef/lemote-2f/dma.c b/arch/mips/loongson2ef/lemote-2f/dma.c
new file mode 100644
index 000000000..3c9e99456
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/dma.c
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/dma-direct.h>
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	return paddr | 0x80000000;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	if (dma_addr > 0x8fffffff)
+		return dma_addr;
+	return dma_addr & 0x0fffffff;
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c
new file mode 100644
index 000000000..d138220e9
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Basic KB3310B Embedded Controller support for the YeeLoong 2F netbook
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-04-20
+ */
+
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+
+#include "ec_kb3310b.h"
+
+static DEFINE_SPINLOCK(index_access_lock);
+static DEFINE_SPINLOCK(port_access_lock);
+
+unsigned char ec_read(unsigned short addr)
+{
+	unsigned char value;
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	value = inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+
+	return value;
+}
+EXPORT_SYMBOL_GPL(ec_read);
+
+void ec_write(unsigned short addr, unsigned char val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	outb(val, EC_IO_PORT_DATA);
+	/*  flush the write action */
+	inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ec_write);
+
+/*
+ * This function is used for EC command writes and corresponding status queries.
+ */
+int ec_query_seq(unsigned char cmd)
+{
+	int timeout;
+	unsigned char status;
+	unsigned long flags;
+	int ret = 0;
+
+	spin_lock_irqsave(&port_access_lock, flags);
+
+	/* make chip goto reset mode */
+	udelay(EC_REG_DELAY);
+	outb(cmd, EC_CMD_PORT);
+	udelay(EC_REG_DELAY);
+
+	/* check if the command is received by ec */
+	timeout = EC_CMD_TIMEOUT;
+	status = inb(EC_STS_PORT);
+	while (timeout-- && (status & (1 << 1))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+
+	spin_unlock_irqrestore(&port_access_lock, flags);
+
+	if (timeout <= 0) {
+		printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
+		ret = -EINVAL;
+	} else
+		printk(KERN_INFO
+			   "(%x/%d)ec issued command %d status : 0x%x\n",
+			   timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(ec_query_seq);
+
+/*
+ * Send query command to EC to get the proper event number
+ */
+int ec_query_event_num(void)
+{
+	return ec_query_seq(CMD_GET_EVENT_NUM);
+}
+EXPORT_SYMBOL(ec_query_event_num);
+
+/*
+ * Get event number from EC
+ *
+ * NOTE: This routine must follow the query_event_num function in the
+ * interrupt.
+ */
+int ec_get_event_num(void)
+{
+	int timeout = 100;
+	unsigned char value;
+	unsigned char status;
+
+	udelay(EC_REG_DELAY);
+	status = inb(EC_STS_PORT);
+	udelay(EC_REG_DELAY);
+	while (timeout-- && !(status & (1 << 0))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+	if (timeout <= 0) {
+		pr_info("%s: get event number timeout.\n", __func__);
+
+		return -EINVAL;
+	}
+	value = inb(EC_DAT_PORT);
+	udelay(EC_REG_DELAY);
+
+	return value;
+}
+EXPORT_SYMBOL(ec_get_event_num);
diff --git a/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h
new file mode 100644
index 000000000..aecdbc9c8
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h
@@ -0,0 +1,184 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * KB3310B Embedded Controller
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-03-14
+ */
+
+#ifndef _EC_KB3310B_H
+#define _EC_KB3310B_H
+
+extern unsigned char ec_read(unsigned short addr);
+extern void ec_write(unsigned short addr, unsigned char val);
+extern int ec_query_seq(unsigned char cmd);
+extern int ec_query_event_num(void);
+extern int ec_get_event_num(void);
+
+typedef int (*sci_handler) (int status);
+extern sci_handler yeeloong_report_lid_status;
+
+#define SCI_IRQ_NUM 0x0A
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1, fill the PORT_HIGH as EC register high part.
+ * 2, fill the PORT_LOW as EC register low part.
+ * 3, fill the PORT_DATA as EC register write data or get the data from it.
+ */
+#define EC_IO_PORT_HIGH 0x0381
+#define EC_IO_PORT_LOW	0x0382
+#define EC_IO_PORT_DATA 0x0383
+
+/*
+ * EC delay time is 500us for register and status access
+ */
+#define EC_REG_DELAY	500	/* unit : us */
+#define EC_CMD_TIMEOUT	0x1000
+
+/*
+ * EC access port for SCI communication
+ */
+#define EC_CMD_PORT		0x66
+#define EC_STS_PORT		0x66
+#define EC_DAT_PORT		0x62
+#define CMD_INIT_IDLE_MODE	0xdd
+#define CMD_EXIT_IDLE_MODE	0xdf
+#define CMD_INIT_RESET_MODE	0xd8
+#define CMD_REBOOT_SYSTEM	0x8c
+#define CMD_GET_EVENT_NUM	0x84
+#define CMD_PROGRAM_PIECE	0xda
+
+/* temperature & fan registers */
+#define REG_TEMPERATURE_VALUE	0xF458
+#define REG_FAN_AUTO_MAN_SWITCH 0xF459
+#define BIT_FAN_AUTO		0
+#define BIT_FAN_MANUAL		1
+#define REG_FAN_CONTROL		0xF4D2
+#define BIT_FAN_CONTROL_ON	(1 << 0)
+#define BIT_FAN_CONTROL_OFF	(0 << 0)
+#define REG_FAN_STATUS		0xF4DA
+#define BIT_FAN_STATUS_ON	(1 << 0)
+#define BIT_FAN_STATUS_OFF	(0 << 0)
+#define REG_FAN_SPEED_HIGH	0xFE22
+#define REG_FAN_SPEED_LOW	0xFE23
+#define REG_FAN_SPEED_LEVEL	0xF4CC
+/* fan speed divider */
+#define FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
+
+/* battery registers */
+#define REG_BAT_DESIGN_CAP_HIGH		0xF77D
+#define REG_BAT_DESIGN_CAP_LOW		0xF77E
+#define REG_BAT_FULLCHG_CAP_HIGH	0xF780
+#define REG_BAT_FULLCHG_CAP_LOW		0xF781
+#define REG_BAT_DESIGN_VOL_HIGH		0xF782
+#define REG_BAT_DESIGN_VOL_LOW		0xF783
+#define REG_BAT_CURRENT_HIGH		0xF784
+#define REG_BAT_CURRENT_LOW		0xF785
+#define REG_BAT_VOLTAGE_HIGH		0xF786
+#define REG_BAT_VOLTAGE_LOW		0xF787
+#define REG_BAT_TEMPERATURE_HIGH	0xF788
+#define REG_BAT_TEMPERATURE_LOW		0xF789
+#define REG_BAT_RELATIVE_CAP_HIGH	0xF492
+#define REG_BAT_RELATIVE_CAP_LOW	0xF493
+#define REG_BAT_VENDOR			0xF4C4
+#define FLAG_BAT_VENDOR_SANYO		0x01
+#define FLAG_BAT_VENDOR_SIMPLO		0x02
+#define REG_BAT_CELL_COUNT		0xF4C6
+#define FLAG_BAT_CELL_3S1P		0x03
+#define FLAG_BAT_CELL_3S2P		0x06
+#define REG_BAT_CHARGE			0xF4A2
+#define FLAG_BAT_CHARGE_DISCHARGE	0x01
+#define FLAG_BAT_CHARGE_CHARGE		0x02
+#define FLAG_BAT_CHARGE_ACPOWER		0x00
+#define REG_BAT_STATUS			0xF4B0
+#define BIT_BAT_STATUS_LOW		(1 << 5)
+#define BIT_BAT_STATUS_DESTROY		(1 << 2)
+#define BIT_BAT_STATUS_FULL		(1 << 1)
+#define BIT_BAT_STATUS_IN		(1 << 0)
+#define REG_BAT_CHARGE_STATUS		0xF4B1
+#define BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
+#define BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
+#define REG_BAT_STATE			0xF482
+#define BIT_BAT_STATE_CHARGING		(1 << 1)
+#define BIT_BAT_STATE_DISCHARGING	(1 << 0)
+#define REG_BAT_POWER			0xF440
+#define BIT_BAT_POWER_S3		(1 << 2)
+#define BIT_BAT_POWER_ON		(1 << 1)
+#define BIT_BAT_POWER_ACIN		(1 << 0)
+
+/* other registers */
+/* Audio: rd/wr */
+#define REG_AUDIO_VOLUME	0xF46C
+#define REG_AUDIO_MUTE		0xF4E7
+#define REG_AUDIO_BEEP		0xF4D0
+/* USB port power or not: rd/wr */
+#define REG_USB0_FLAG		0xF461
+#define REG_USB1_FLAG		0xF462
+#define REG_USB2_FLAG		0xF463
+#define BIT_USB_FLAG_ON		1
+#define BIT_USB_FLAG_OFF	0
+/* LID */
+#define REG_LID_DETECT		0xF4BD
+#define BIT_LID_DETECT_ON	1
+#define BIT_LID_DETECT_OFF	0
+/* CRT */
+#define REG_CRT_DETECT		0xF4AD
+#define BIT_CRT_DETECT_PLUG	1
+#define BIT_CRT_DETECT_UNPLUG	0
+/* LCD backlight brightness adjust: 9 levels */
+#define REG_DISPLAY_BRIGHTNESS	0xF4F5
+/* Black screen Status */
+#define BIT_DISPLAY_LCD_ON	1
+#define BIT_DISPLAY_LCD_OFF	0
+/* LCD backlight control: off/restore */
+#define REG_BACKLIGHT_CTRL	0xF7BD
+#define BIT_BACKLIGHT_ON	1
+#define BIT_BACKLIGHT_OFF	0
+/* Reset the machine auto-clear: rd/wr */
+#define REG_RESET		0xF4EC
+#define BIT_RESET_ON		1
+/* Light the led: rd/wr */
+#define REG_LED			0xF4C8
+#define BIT_LED_RED_POWER	(1 << 0)
+#define BIT_LED_ORANGE_POWER	(1 << 1)
+#define BIT_LED_GREEN_CHARGE	(1 << 2)
+#define BIT_LED_RED_CHARGE	(1 << 3)
+#define BIT_LED_NUMLOCK		(1 << 4)
+/* Test led mode, all led on/off */
+#define REG_LED_TEST		0xF4C2
+#define BIT_LED_TEST_IN		1
+#define BIT_LED_TEST_OUT	0
+/* Camera on/off */
+#define REG_CAMERA_STATUS	0xF46A
+#define BIT_CAMERA_STATUS_ON	1
+#define BIT_CAMERA_STATUS_OFF	0
+#define REG_CAMERA_CONTROL	0xF7B7
+#define BIT_CAMERA_CONTROL_OFF	0
+#define BIT_CAMERA_CONTROL_ON	1
+/* Wlan Status */
+#define REG_WLAN		0xF4FA
+#define BIT_WLAN_ON		1
+#define BIT_WLAN_OFF		0
+#define REG_DISPLAY_LCD		0xF79F
+
+/* SCI Event Number from EC */
+enum {
+	EVENT_LID = 0x23,	/*  LID open/close */
+	EVENT_DISPLAY_TOGGLE,	/*  Fn+F3 for display switch */
+	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
+	EVENT_OVERTEMP,		/*  Over-temperature happened */
+	EVENT_CRT_DETECT,	/*  CRT is connected */
+	EVENT_CAMERA,		/*  Camera on/off */
+	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
+	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
+	EVENT_BLACK_SCREEN,	/*  Turn on/off backlight */
+	EVENT_AUDIO_MUTE,	/*  Mute on/off */
+	EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
+	EVENT_AC_BAT,		/*  AC & Battery relative issue */
+	EVENT_AUDIO_VOLUME,	/*  Volume adjust */
+	EVENT_WLAN,		/*  Wlan on/off */
+	EVENT_END
+};
+
+#endif /* !_EC_KB3310B_H */
diff --git a/arch/mips/loongson2ef/lemote-2f/irq.c b/arch/mips/loongson2ef/lemote-2f/irq.c
new file mode 100644
index 000000000..f5a731a2a
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/irq.c
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc.
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+
+#include <loongson.h>
+#include <machine.h>
+
+#define LOONGSON_TIMER_IRQ	(MIPS_CPU_IRQ_BASE + 7) /* cpu timer */
+#define LOONGSON_NORTH_BRIDGE_IRQ	(MIPS_CPU_IRQ_BASE + 6) /* bonito */
+#define LOONGSON_UART_IRQ	(MIPS_CPU_IRQ_BASE + 3) /* cpu serial port */
+#define LOONGSON_SOUTH_BRIDGE_IRQ	(MIPS_CPU_IRQ_BASE + 2) /* i8259 */
+
+#define LOONGSON_INT_BIT_INT0		(1 << 11)
+#define LOONGSON_INT_BIT_INT1		(1 << 12)
+
+/*
+ * The generic i8259_irq() make the kernel hang on booting.  Since we cannot
+ * get the irq via the IRR directly, we access the ISR instead.
+ */
+int mach_i8259_irq(void)
+{
+	int irq, isr;
+
+	irq = -1;
+
+	if ((LOONGSON_INTISR & LOONGSON_INTEN) & LOONGSON_INT_BIT_INT0) {
+		raw_spin_lock(&i8259A_lock);
+		isr = inb(PIC_MASTER_CMD) &
+			~inb(PIC_MASTER_IMR) & ~(1 << PIC_CASCADE_IR);
+		if (!isr)
+			isr = (inb(PIC_SLAVE_CMD) & ~inb(PIC_SLAVE_IMR)) << 8;
+		irq = ffs(isr) - 1;
+		if (unlikely(irq == 7)) {
+			/*
+			 * This may be a spurious interrupt.
+			 *
+			 * Read the interrupt status register (ISR). If the most
+			 * significant bit is not set then there is no valid
+			 * interrupt.
+			 */
+			outb(0x0B, PIC_MASTER_ISR);	/* ISR register */
+			if (~inb(PIC_MASTER_ISR) & 0x80)
+				irq = -1;
+		}
+		raw_spin_unlock(&i8259A_lock);
+	}
+
+	return irq;
+}
+EXPORT_SYMBOL(mach_i8259_irq);
+
+static void i8259_irqdispatch(void)
+{
+	int irq;
+
+	irq = mach_i8259_irq();
+	if (irq >= 0)
+		do_IRQ(irq);
+	else
+		spurious_interrupt();
+}
+
+void mach_irq_dispatch(unsigned int pending)
+{
+	if (pending & CAUSEF_IP7)
+		do_IRQ(LOONGSON_TIMER_IRQ);
+	else if (pending & CAUSEF_IP6) {	/* North Bridge, Perf counter */
+		bonito_irqdispatch();
+	} else if (pending & CAUSEF_IP3)	/* CPU UART */
+		do_IRQ(LOONGSON_UART_IRQ);
+	else if (pending & CAUSEF_IP2)	/* South Bridge */
+		i8259_irqdispatch();
+	else
+		spurious_interrupt();
+}
+
+static irqreturn_t ip6_action(int cpl, void *dev_id)
+{
+	return IRQ_HANDLED;
+}
+
+void __init mach_init_irq(void)
+{
+	/* init all controller
+	 *   0-15	  ------> i8259 interrupt
+	 *   16-23	  ------> mips cpu interrupt
+	 *   32-63	  ------> bonito irq
+	 */
+
+	/* setup cs5536 as high level trigger */
+	LOONGSON_INTPOL = LOONGSON_INT_BIT_INT0 | LOONGSON_INT_BIT_INT1;
+	LOONGSON_INTEDGE &= ~(LOONGSON_INT_BIT_INT0 | LOONGSON_INT_BIT_INT1);
+
+	/* Sets the first-level interrupt dispatcher. */
+	mips_cpu_irq_init();
+	init_i8259_irqs();
+	bonito_irq_init();
+
+	/* setup north bridge irq (bonito) */
+	if (request_irq(LOONGSON_NORTH_BRIDGE_IRQ, ip6_action,
+			IRQF_SHARED | IRQF_NO_THREAD, "cascade", ip6_action))
+		pr_err("Failed to register north bridge cascade interrupt\n");
+	/* setup source bridge irq (i8259) */
+	if (request_irq(LOONGSON_SOUTH_BRIDGE_IRQ, no_action,
+			IRQF_NO_THREAD | IRQF_NO_SUSPEND, "cascade", NULL))
+		pr_err("Failed to register south bridge cascade interrupt\n");
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/machtype.c b/arch/mips/loongson2ef/lemote-2f/machtype.c
new file mode 100644
index 000000000..9462a3ab5
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/machtype.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+void __init mach_prom_init_machtype(void)
+{
+	/* We share the same kernel image file among Lemote 2F family
+	 * of machines, and provide the machtype= kernel command line
+	 * to users to indicate their machine, this command line will
+	 * be passed by the latest PMON automatically. and fortunately,
+	 * up to now, we can get the machine type from the PMON_VER=
+	 * commandline directly except the NAS machine, In the old
+	 * machines, this will help the users a lot.
+	 *
+	 * If no "machtype=" passed, get machine type from "PMON_VER=".
+	 *	PMON_VER=LM8089		Lemote 8.9'' netbook
+	 *		 LM8101		Lemote 10.1'' netbook
+	 *	(The above two netbooks have the same kernel support)
+	 *		 LM6XXX		Lemote FuLoong(2F) box series
+	 *		 LM9XXX		Lemote LynLoong PC series
+	 */
+	if (strstr(arcs_cmdline, "PMON_VER=LM")) {
+		if (strstr(arcs_cmdline, "PMON_VER=LM8"))
+			mips_machtype = MACH_LEMOTE_YL2F89;
+		else if (strstr(arcs_cmdline, "PMON_VER=LM6"))
+			mips_machtype = MACH_LEMOTE_FL2F;
+		else if (strstr(arcs_cmdline, "PMON_VER=LM9"))
+			mips_machtype = MACH_LEMOTE_LL2F;
+		else
+			mips_machtype = MACH_LEMOTE_NAS;
+
+		strcat(arcs_cmdline, " machtype=");
+		strcat(arcs_cmdline, get_system_type());
+		strcat(arcs_cmdline, " ");
+	}
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/pm.c b/arch/mips/loongson2ef/lemote-2f/pm.c
new file mode 100644
index 000000000..3d0027229
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/pm.c
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Lemote loongson2f family machines' specific suspend support
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+#include <linux/i8042.h>
+#include <linux/export.h>
+
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+#include <cs5536/cs5536_mfgpt.h>
+#include "ec_kb3310b.h"
+
+#define I8042_KBD_IRQ		1
+#define I8042_CTR_KBDINT	0x01
+#define I8042_CTR_KBDDIS	0x10
+
+static unsigned char i8042_ctr;
+
+static int i8042_enable_kbd_port(void)
+{
+	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_RCTR)) {
+		pr_err("i8042.c: Can't read CTR while enabling i8042 kbd port."
+		       "\n");
+		return -EIO;
+	}
+
+	i8042_ctr &= ~I8042_CTR_KBDDIS;
+	i8042_ctr |= I8042_CTR_KBDINT;
+
+	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
+		i8042_ctr &= ~I8042_CTR_KBDINT;
+		i8042_ctr |= I8042_CTR_KBDDIS;
+		pr_err("i8042.c: Failed to enable KBD port.\n");
+
+		return -EIO;
+	}
+
+	return 0;
+}
+
+void setup_wakeup_events(void)
+{
+	int irq_mask;
+
+	switch (mips_machtype) {
+	case MACH_LEMOTE_ML2F7:
+	case MACH_LEMOTE_YL2F89:
+		/* open the keyboard irq in i8259A */
+		outb((0xff & ~(1 << I8042_KBD_IRQ)), PIC_MASTER_IMR);
+		irq_mask = inb(PIC_MASTER_IMR);
+
+		/* enable keyboard port */
+		i8042_enable_kbd_port();
+
+		/* Wakeup CPU via SCI lid open event */
+		outb(irq_mask & ~(1 << PIC_CASCADE_IR), PIC_MASTER_IMR);
+		inb(PIC_MASTER_IMR);
+		outb(0xff & ~(1 << (SCI_IRQ_NUM - 8)), PIC_SLAVE_IMR);
+		inb(PIC_SLAVE_IMR);
+
+		break;
+
+	default:
+		break;
+	}
+}
+
+static struct delayed_work lid_task;
+static int initialized;
+/* yeeloong_report_lid_status will be implemented in yeeloong_laptop.c */
+sci_handler yeeloong_report_lid_status;
+EXPORT_SYMBOL(yeeloong_report_lid_status);
+static void yeeloong_lid_update_task(struct work_struct *work)
+{
+	if (yeeloong_report_lid_status)
+		yeeloong_report_lid_status(BIT_LID_DETECT_ON);
+}
+
+int wakeup_loongson(void)
+{
+	int irq;
+
+	/* query the interrupt number */
+	irq = mach_i8259_irq();
+	if (irq < 0)
+		return 0;
+
+	printk(KERN_INFO "%s: irq = %d\n", __func__, irq);
+
+	if (irq == I8042_KBD_IRQ)
+		return 1;
+	else if (irq == SCI_IRQ_NUM) {
+		int ret, sci_event;
+		/* query the event number */
+		ret = ec_query_seq(CMD_GET_EVENT_NUM);
+		if (ret < 0)
+			return 0;
+		sci_event = ec_get_event_num();
+		if (sci_event < 0)
+			return 0;
+		if (sci_event == EVENT_LID) {
+			int lid_status;
+			/* check the LID status */
+			lid_status = ec_read(REG_LID_DETECT);
+			/* wakeup cpu when people open the LID */
+			if (lid_status == BIT_LID_DETECT_ON) {
+				/* If we call it directly here, the WARNING
+				 * will be sent out by getnstimeofday
+				 * via "WARN_ON(timekeeping_suspended);"
+				 * because we can not schedule in suspend mode.
+				 */
+				if (initialized == 0) {
+					INIT_DELAYED_WORK(&lid_task,
+						yeeloong_lid_update_task);
+					initialized = 1;
+				}
+				schedule_delayed_work(&lid_task, 1);
+				return 1;
+			}
+		}
+	}
+
+	return 0;
+}
+
+void __weak mach_suspend(void)
+{
+	disable_mfgpt0_counter();
+}
+
+void __weak mach_resume(void)
+{
+	enable_mfgpt0_counter();
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/reset.c b/arch/mips/loongson2ef/lemote-2f/reset.c
new file mode 100644
index 000000000..197dae4ff
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/reset.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* Board-specific reboot/shutdown routines
+ *
+ * Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca>
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+#include <cs5536/cs5536.h>
+#include "ec_kb3310b.h"
+
+static void reset_cpu(void)
+{
+	/*
+	 * reset cpu to full speed, this is needed when enabling cpu frequency
+	 * scalling
+	 */
+	writel(readl(LOONGSON_CHIPCFG) | 0x7, LOONGSON_CHIPCFG);
+}
+
+/* reset support for fuloong2f */
+
+static void fl2f_reboot(void)
+{
+	reset_cpu();
+
+	/* send a reset signal to south bridge.
+	 *
+	 * NOTE: if enable "Power Management" in kernel, rtl8169 will not reset
+	 * normally with this reset operation and it will not work in PMON, but
+	 * you can type halt command and then reboot, seems the hardware reset
+	 * logic not work normally.
+	 */
+	{
+		u32 hi, lo;
+		_rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo);
+		lo |= 0x00000001;
+		_wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo);
+	}
+}
+
+static void fl2f_shutdown(void)
+{
+	u32 hi, lo, val;
+	int gpio_base;
+
+	/* get gpio base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
+	gpio_base = lo & 0xff00;
+
+	/* make cs5536 gpio13 output enable */
+	val = inl(gpio_base + GPIOL_OUT_EN);
+	val &= ~(1 << (16 + 13));
+	val |= (1 << 13);
+	outl(val, gpio_base + GPIOL_OUT_EN);
+	mmiowb();
+	/* make cs5536 gpio13 output low level voltage. */
+	val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13));
+	val |= (1 << (16 + 13));
+	outl(val, gpio_base + GPIOL_OUT_VAL);
+	mmiowb();
+}
+
+/* reset support for yeeloong2f and mengloong2f notebook */
+
+static void ml2f_reboot(void)
+{
+	reset_cpu();
+
+	/* sending an reset signal to EC(embedded controller) */
+	ec_write(REG_RESET, BIT_RESET_ON);
+}
+
+#define yl2f89_reboot ml2f_reboot
+
+/* menglong(7inches) laptop has different shutdown logic from 8.9inches */
+#define EC_SHUTDOWN_IO_PORT_HIGH 0xff2d
+#define EC_SHUTDOWN_IO_PORT_LOW	 0xff2e
+#define EC_SHUTDOWN_IO_PORT_DATA 0xff2f
+#define REG_SHUTDOWN_HIGH	 0xFC
+#define REG_SHUTDOWN_LOW	 0x29
+#define BIT_SHUTDOWN_ON		 (1 << 1)
+
+static void ml2f_shutdown(void)
+{
+	u8 val;
+	u64 i;
+
+	outb(REG_SHUTDOWN_HIGH, EC_SHUTDOWN_IO_PORT_HIGH);
+	outb(REG_SHUTDOWN_LOW, EC_SHUTDOWN_IO_PORT_LOW);
+	mmiowb();
+	val = inb(EC_SHUTDOWN_IO_PORT_DATA);
+	outb(val & (~BIT_SHUTDOWN_ON), EC_SHUTDOWN_IO_PORT_DATA);
+	mmiowb();
+	/* need enough wait here... how many microseconds needs? */
+	for (i = 0; i < 0x10000; i++)
+		delay();
+	outb(val | BIT_SHUTDOWN_ON, EC_SHUTDOWN_IO_PORT_DATA);
+	mmiowb();
+}
+
+static void yl2f89_shutdown(void)
+{
+	/* cpu-gpio0 output low */
+	LOONGSON_GPIODATA &= ~0x00000001;
+	/* cpu-gpio0 as output */
+	LOONGSON_GPIOIE &= ~0x00000001;
+}
+
+void mach_prepare_reboot(void)
+{
+	switch (mips_machtype) {
+	case MACH_LEMOTE_FL2F:
+	case MACH_LEMOTE_NAS:
+	case MACH_LEMOTE_LL2F:
+		fl2f_reboot();
+		break;
+	case MACH_LEMOTE_ML2F7:
+		ml2f_reboot();
+		break;
+	case MACH_LEMOTE_YL2F89:
+		yl2f89_reboot();
+		break;
+	default:
+		break;
+	}
+}
+
+void mach_prepare_shutdown(void)
+{
+	switch (mips_machtype) {
+	case MACH_LEMOTE_FL2F:
+	case MACH_LEMOTE_NAS:
+	case MACH_LEMOTE_LL2F:
+		fl2f_shutdown();
+		break;
+	case MACH_LEMOTE_ML2F7:
+		ml2f_shutdown();
+		break;
+	case MACH_LEMOTE_YL2F89:
+		yl2f89_shutdown();
+		break;
+	default:
+		break;
+	}
+}