Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

3 files changed, 642 insertions, 0 deletions

diff --git a/arch/sh/boards/mach-ap325rxa/Makefile b/arch/sh/boards/mach-ap325rxa/Makefile
new file mode 100644
index 000000000..dba5d0c20
--- /dev/null
+++ b/arch/sh/boards/mach-ap325rxa/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-y	 := setup.o sdram.o
+
diff --git a/arch/sh/boards/mach-ap325rxa/sdram.S b/arch/sh/boards/mach-ap325rxa/sdram.S
new file mode 100644
index 000000000..541c82cc3
--- /dev/null
+++ b/arch/sh/boards/mach-ap325rxa/sdram.S
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * AP325RXA sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(ap325rxa_sdram_enter_start)
+
+	/* SBSC: disable power down and put in self-refresh mode */
+	mov.l	1f, r4
+	mov.l	2f, r1
+	mov.l	@r4, r2
+	or	r1, r2
+	mov.l   3f, r3
+	and	r3, r2
+	mov.l	r2, @r4
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+2:	.long	0x00000400
+3:	.long	0xffff7fff
+ENTRY(ap325rxa_sdram_enter_end)
+
+	.balign 4
+ENTRY(ap325rxa_sdram_leave_start)
+
+	/* SBSC: set auto-refresh mode */
+	mov.l	1f, r4
+	mov.l	@r4, r0
+	mov.l   4f, r1
+	and	r1, r0
+	mov.l	r0, @r4
+	mov.l	6f, r4
+	mov.l	8f, r0
+	mov.l	@r4, r1
+	mov	#-1, r4
+	add	r4, r1
+	or	r1, r0
+	mov.l	7f, r1
+	mov.l	r0, @r1
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+4:	.long	0xfffffbff
+6:	.long   0xfe40001c /* RTCOR */
+7:	.long   0xfe400018 /* RTCNT */
+8:	.long   0xa55a0000
+ENTRY(ap325rxa_sdram_leave_end)
diff --git a/arch/sh/boards/mach-ap325rxa/setup.c b/arch/sh/boards/mach-ap325rxa/setup.c
new file mode 100644
index 000000000..c77b5f00a
--- /dev/null
+++ b/arch/sh/boards/mach-ap325rxa/setup.c
@@ -0,0 +1,573 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Renesas - AP-325RXA
+ * (Compatible with Algo System ., LTD. - AP-320A)
+ *
+ * Copyright (C) 2008 Renesas Solutions Corp.
+ * Author : Yusuke Goda <goda.yuske@renesas.com>
+ */
+
+#include <asm/clock.h>
+#include <asm/io.h>
+#include <asm/suspend.h>
+
+#include <cpu/sh7723.h>
+
+#include <linux/dma-map-ops.h>
+#include <linux/clkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/memblock.h>
+#include <linux/mfd/tmio.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/sh_flctl.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/sh_intc.h>
+#include <linux/smsc911x.h>
+#include <linux/videodev2.h>
+
+#include <media/drv-intf/renesas-ceu.h>
+#include <media/i2c/ov772x.h>
+
+#include <video/sh_mobile_lcdc.h>
+
+#define CEU_BUFFER_MEMORY_SIZE		(4 << 20)
+static phys_addr_t ceu_dma_membase;
+
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags		= SMSC911X_USE_32BIT,
+};
+
+static struct resource smsc9118_resources[] = {
+	[0] = {
+		.start	= 0xb6080000,
+		.end	= 0xb60fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x660),
+		.end	= evt2irq(0x660),
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device smsc9118_device = {
+	.name		= "smsc911x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smsc9118_resources),
+	.resource	= smsc9118_resources,
+	.dev		= {
+		.platform_data = &smsc911x_config,
+	},
+};
+
+/*
+ * AP320 and AP325RXA has CPLD data in NOR Flash(0xA80000-0xABFFFF).
+ * If this area erased, this board can not boot.
+ */
+static struct mtd_partition ap325rxa_nor_flash_partitions[] = {
+	{
+		.name = "uboot",
+		.offset = 0,
+		.size = (1 * 1024 * 1024),
+		.mask_flags = MTD_WRITEABLE,	/* Read-only */
+	}, {
+		.name = "kernel",
+		.offset = MTDPART_OFS_APPEND,
+		.size = (2 * 1024 * 1024),
+	}, {
+		.name = "free-area0",
+		.offset = MTDPART_OFS_APPEND,
+		.size = ((7 * 1024 * 1024) + (512 * 1024)),
+	}, {
+		.name = "CPLD-Data",
+		.offset = MTDPART_OFS_APPEND,
+		.mask_flags = MTD_WRITEABLE,	/* Read-only */
+		.size = (1024 * 128 * 2),
+	}, {
+		.name = "free-area1",
+		.offset = MTDPART_OFS_APPEND,
+		.size = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data ap325rxa_nor_flash_data = {
+	.width		= 2,
+	.parts		= ap325rxa_nor_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(ap325rxa_nor_flash_partitions),
+};
+
+static struct resource ap325rxa_nor_flash_resources[] = {
+	[0] = {
+		.name	= "NOR Flash",
+		.start	= 0x00000000,
+		.end	= 0x00ffffff,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device ap325rxa_nor_flash_device = {
+	.name		= "physmap-flash",
+	.resource	= ap325rxa_nor_flash_resources,
+	.num_resources	= ARRAY_SIZE(ap325rxa_nor_flash_resources),
+	.dev		= {
+		.platform_data = &ap325rxa_nor_flash_data,
+	},
+};
+
+static struct mtd_partition nand_partition_info[] = {
+	{
+		.name	= "nand_data",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct resource nand_flash_resources[] = {
+	[0] = {
+		.start	= 0xa4530000,
+		.end	= 0xa45300ff,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct sh_flctl_platform_data nand_flash_data = {
+	.parts		= nand_partition_info,
+	.nr_parts	= ARRAY_SIZE(nand_partition_info),
+	.flcmncr_val	= FCKSEL_E | TYPESEL_SET | NANWF_E,
+	.has_hwecc	= 1,
+};
+
+static struct platform_device nand_flash_device = {
+	.name		= "sh_flctl",
+	.resource	= nand_flash_resources,
+	.num_resources	= ARRAY_SIZE(nand_flash_resources),
+	.dev		= {
+		.platform_data = &nand_flash_data,
+	},
+};
+
+#define FPGA_LCDREG	0xB4100180
+#define FPGA_BKLREG	0xB4100212
+#define FPGA_LCDREG_VAL	0x0018
+#define PORT_MSELCRB	0xA4050182
+#define PORT_HIZCRC	0xA405015C
+#define PORT_DRVCRA	0xA405018A
+#define PORT_DRVCRB	0xA405018C
+
+static int ap320_wvga_set_brightness(int brightness)
+{
+	if (brightness) {
+		gpio_set_value(GPIO_PTS3, 0);
+		__raw_writew(0x100, FPGA_BKLREG);
+	} else {
+		__raw_writew(0, FPGA_BKLREG);
+		gpio_set_value(GPIO_PTS3, 1);
+	}
+
+	return 0;
+}
+
+static void ap320_wvga_power_on(void)
+{
+	msleep(100);
+
+	/* ASD AP-320/325 LCD ON */
+	__raw_writew(FPGA_LCDREG_VAL, FPGA_LCDREG);
+}
+
+static void ap320_wvga_power_off(void)
+{
+	/* ASD AP-320/325 LCD OFF */
+	__raw_writew(0, FPGA_LCDREG);
+}
+
+static const struct fb_videomode ap325rxa_lcdc_modes[] = {
+	{
+		.name = "LB070WV1",
+		.xres = 800,
+		.yres = 480,
+		.left_margin = 32,
+		.right_margin = 160,
+		.hsync_len = 8,
+		.upper_margin = 63,
+		.lower_margin = 80,
+		.vsync_len = 1,
+		.sync = 0, /* hsync and vsync are active low */
+	},
+};
+
+static struct sh_mobile_lcdc_info lcdc_info = {
+	.clock_source = LCDC_CLK_EXTERNAL,
+	.ch[0] = {
+		.chan = LCDC_CHAN_MAINLCD,
+		.fourcc = V4L2_PIX_FMT_RGB565,
+		.interface_type = RGB18,
+		.clock_divider = 1,
+		.lcd_modes = ap325rxa_lcdc_modes,
+		.num_modes = ARRAY_SIZE(ap325rxa_lcdc_modes),
+		.panel_cfg = {
+			.width = 152,	/* 7.0 inch */
+			.height = 91,
+			.display_on = ap320_wvga_power_on,
+			.display_off = ap320_wvga_power_off,
+		},
+		.bl_info = {
+			.name = "sh_mobile_lcdc_bl",
+			.max_brightness = 1,
+			.set_brightness = ap320_wvga_set_brightness,
+		},
+	}
+};
+
+static struct resource lcdc_resources[] = {
+	[0] = {
+		.name	= "LCDC",
+		.start	= 0xfe940000, /* P4-only space */
+		.end	= 0xfe942fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x580),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device lcdc_device = {
+	.name		= "sh_mobile_lcdc_fb",
+	.num_resources	= ARRAY_SIZE(lcdc_resources),
+	.resource	= lcdc_resources,
+	.dev		= {
+		.platform_data	= &lcdc_info,
+	},
+};
+
+/* Powerdown/reset gpios for CEU image sensors */
+static struct gpiod_lookup_table ov7725_gpios = {
+	.dev_id		= "0-0021",
+	.table		= {
+		GPIO_LOOKUP("sh7723_pfc", GPIO_PTZ5, "reset", GPIO_ACTIVE_LOW),
+	},
+};
+
+static struct ceu_platform_data ceu0_pdata = {
+	.num_subdevs			= 1,
+	.subdevs = {
+		{ /* [0] = ov7725  */
+			.flags		= 0,
+			.bus_width	= 8,
+			.bus_shift	= 0,
+			.i2c_adapter_id	= 0,
+			.i2c_address	= 0x21,
+		},
+	},
+};
+
+static struct resource ceu_resources[] = {
+	[0] = {
+		.name	= "CEU",
+		.start	= 0xfe910000,
+		.end	= 0xfe91009f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = evt2irq(0x880),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device ap325rxa_ceu_device = {
+	.name		= "renesas-ceu",
+	.id             = 0, /* "ceu.0" clock */
+	.num_resources	= ARRAY_SIZE(ceu_resources),
+	.resource	= ceu_resources,
+	.dev		= {
+		.platform_data	= &ceu0_pdata,
+	},
+};
+
+/* Fixed 3.3V regulators to be used by SDHI0, SDHI1 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
+static struct resource sdhi0_cn3_resources[] = {
+	[0] = {
+		.name	= "SDHI0",
+		.start	= 0x04ce0000,
+		.end	= 0x04ce00ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0xe80),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct tmio_mmc_data sdhi0_cn3_data = {
+	.capabilities	= MMC_CAP_SDIO_IRQ,
+};
+
+static struct platform_device sdhi0_cn3_device = {
+	.name		= "sh_mobile_sdhi",
+	.id             = 0, /* "sdhi0" clock */
+	.num_resources	= ARRAY_SIZE(sdhi0_cn3_resources),
+	.resource	= sdhi0_cn3_resources,
+	.dev = {
+		.platform_data = &sdhi0_cn3_data,
+	},
+};
+
+static struct resource sdhi1_cn7_resources[] = {
+	[0] = {
+		.name	= "SDHI1",
+		.start	= 0x04cf0000,
+		.end	= 0x04cf00ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x4e0),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct tmio_mmc_data sdhi1_cn7_data = {
+	.capabilities	= MMC_CAP_SDIO_IRQ,
+};
+
+static struct platform_device sdhi1_cn7_device = {
+	.name		= "sh_mobile_sdhi",
+	.id             = 1, /* "sdhi1" clock */
+	.num_resources	= ARRAY_SIZE(sdhi1_cn7_resources),
+	.resource	= sdhi1_cn7_resources,
+	.dev = {
+		.platform_data = &sdhi1_cn7_data,
+	},
+};
+
+static struct ov772x_camera_info ov7725_info = {
+	.flags		= OV772X_FLAG_VFLIP | OV772X_FLAG_HFLIP,
+	.edgectrl	= OV772X_AUTO_EDGECTRL(0xf, 0),
+};
+
+static struct i2c_board_info ap325rxa_i2c_devices[] __initdata = {
+	{
+		I2C_BOARD_INFO("pcf8563", 0x51),
+	},
+	{
+		I2C_BOARD_INFO("ov772x", 0x21),
+		.platform_data = &ov7725_info,
+	},
+};
+
+static struct platform_device *ap325rxa_devices[] __initdata = {
+	&smsc9118_device,
+	&ap325rxa_nor_flash_device,
+	&lcdc_device,
+	&nand_flash_device,
+	&sdhi0_cn3_device,
+	&sdhi1_cn7_device,
+};
+
+extern char ap325rxa_sdram_enter_start;
+extern char ap325rxa_sdram_enter_end;
+extern char ap325rxa_sdram_leave_start;
+extern char ap325rxa_sdram_leave_end;
+
+static int __init ap325rxa_devices_setup(void)
+{
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&ap325rxa_sdram_enter_start,
+					&ap325rxa_sdram_enter_end,
+					&ap325rxa_sdram_leave_start,
+					&ap325rxa_sdram_leave_end);
+
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
+	/* LD3 and LD4 LEDs */
+	gpio_request(GPIO_PTX5, NULL); /* RUN */
+	gpio_direction_output(GPIO_PTX5, 1);
+	gpio_export(GPIO_PTX5, 0);
+
+	gpio_request(GPIO_PTX4, NULL); /* INDICATOR */
+	gpio_direction_output(GPIO_PTX4, 0);
+	gpio_export(GPIO_PTX4, 0);
+
+	/* SW1 input */
+	gpio_request(GPIO_PTF7, NULL); /* MODE */
+	gpio_direction_input(GPIO_PTF7);
+	gpio_export(GPIO_PTF7, 0);
+
+	/* LCDC */
+	gpio_request(GPIO_FN_LCDD15, NULL);
+	gpio_request(GPIO_FN_LCDD14, NULL);
+	gpio_request(GPIO_FN_LCDD13, NULL);
+	gpio_request(GPIO_FN_LCDD12, NULL);
+	gpio_request(GPIO_FN_LCDD11, NULL);
+	gpio_request(GPIO_FN_LCDD10, NULL);
+	gpio_request(GPIO_FN_LCDD9, NULL);
+	gpio_request(GPIO_FN_LCDD8, NULL);
+	gpio_request(GPIO_FN_LCDD7, NULL);
+	gpio_request(GPIO_FN_LCDD6, NULL);
+	gpio_request(GPIO_FN_LCDD5, NULL);
+	gpio_request(GPIO_FN_LCDD4, NULL);
+	gpio_request(GPIO_FN_LCDD3, NULL);
+	gpio_request(GPIO_FN_LCDD2, NULL);
+	gpio_request(GPIO_FN_LCDD1, NULL);
+	gpio_request(GPIO_FN_LCDD0, NULL);
+	gpio_request(GPIO_FN_LCDLCLK_PTR, NULL);
+	gpio_request(GPIO_FN_LCDDCK, NULL);
+	gpio_request(GPIO_FN_LCDVEPWC, NULL);
+	gpio_request(GPIO_FN_LCDVCPWC, NULL);
+	gpio_request(GPIO_FN_LCDVSYN, NULL);
+	gpio_request(GPIO_FN_LCDHSYN, NULL);
+	gpio_request(GPIO_FN_LCDDISP, NULL);
+	gpio_request(GPIO_FN_LCDDON, NULL);
+
+	/* LCD backlight */
+	gpio_request(GPIO_PTS3, NULL);
+	gpio_direction_output(GPIO_PTS3, 1);
+
+	/* CEU */
+	gpio_request(GPIO_FN_VIO_CLK2, NULL);
+	gpio_request(GPIO_FN_VIO_VD2, NULL);
+	gpio_request(GPIO_FN_VIO_HD2, NULL);
+	gpio_request(GPIO_FN_VIO_FLD, NULL);
+	gpio_request(GPIO_FN_VIO_CKO, NULL);
+	gpio_request(GPIO_FN_VIO_D15, NULL);
+	gpio_request(GPIO_FN_VIO_D14, NULL);
+	gpio_request(GPIO_FN_VIO_D13, NULL);
+	gpio_request(GPIO_FN_VIO_D12, NULL);
+	gpio_request(GPIO_FN_VIO_D11, NULL);
+	gpio_request(GPIO_FN_VIO_D10, NULL);
+	gpio_request(GPIO_FN_VIO_D9, NULL);
+	gpio_request(GPIO_FN_VIO_D8, NULL);
+
+	gpio_request(GPIO_PTZ7, NULL);
+	gpio_direction_output(GPIO_PTZ7, 0); /* OE_CAM */
+	gpio_request(GPIO_PTZ6, NULL);
+	gpio_direction_output(GPIO_PTZ6, 0); /* STBY_CAM */
+	gpio_request(GPIO_PTZ5, NULL);
+	gpio_direction_output(GPIO_PTZ5, 0); /* RST_CAM */
+	gpio_request(GPIO_PTZ4, NULL);
+	gpio_direction_output(GPIO_PTZ4, 0); /* SADDR */
+
+	__raw_writew(__raw_readw(PORT_MSELCRB) & ~0x0001, PORT_MSELCRB);
+
+	/* FLCTL */
+	gpio_request(GPIO_FN_FCE, NULL);
+	gpio_request(GPIO_FN_NAF7, NULL);
+	gpio_request(GPIO_FN_NAF6, NULL);
+	gpio_request(GPIO_FN_NAF5, NULL);
+	gpio_request(GPIO_FN_NAF4, NULL);
+	gpio_request(GPIO_FN_NAF3, NULL);
+	gpio_request(GPIO_FN_NAF2, NULL);
+	gpio_request(GPIO_FN_NAF1, NULL);
+	gpio_request(GPIO_FN_NAF0, NULL);
+	gpio_request(GPIO_FN_FCDE, NULL);
+	gpio_request(GPIO_FN_FOE, NULL);
+	gpio_request(GPIO_FN_FSC, NULL);
+	gpio_request(GPIO_FN_FWE, NULL);
+	gpio_request(GPIO_FN_FRB, NULL);
+
+	__raw_writew(0, PORT_HIZCRC);
+	__raw_writew(0xFFFF, PORT_DRVCRA);
+	__raw_writew(0xFFFF, PORT_DRVCRB);
+
+	/* SDHI0 - CN3 - SD CARD */
+	gpio_request(GPIO_FN_SDHI0CD_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0WP_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D3_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D2_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D1_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0D0_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0CMD_PTD, NULL);
+	gpio_request(GPIO_FN_SDHI0CLK_PTD, NULL);
+
+	/* SDHI1 - CN7 - MICRO SD CARD */
+	gpio_request(GPIO_FN_SDHI1CD, NULL);
+	gpio_request(GPIO_FN_SDHI1D3, NULL);
+	gpio_request(GPIO_FN_SDHI1D2, NULL);
+	gpio_request(GPIO_FN_SDHI1D1, NULL);
+	gpio_request(GPIO_FN_SDHI1D0, NULL);
+	gpio_request(GPIO_FN_SDHI1CMD, NULL);
+	gpio_request(GPIO_FN_SDHI1CLK, NULL);
+
+	/* Add a clock alias for ov7725 xclk source. */
+	clk_add_alias(NULL, "0-0021", "video_clk", NULL);
+
+	/* Register RSTB gpio for ov7725 camera sensor. */
+	gpiod_add_lookup_table(&ov7725_gpios);
+
+	i2c_register_board_info(0, ap325rxa_i2c_devices,
+				ARRAY_SIZE(ap325rxa_i2c_devices));
+
+	/* Initialize CEU platform device separately to map memory first */
+	device_initialize(&ap325rxa_ceu_device.dev);
+	dma_declare_coherent_memory(&ap325rxa_ceu_device.dev,
+			ceu_dma_membase, ceu_dma_membase,
+			ceu_dma_membase + CEU_BUFFER_MEMORY_SIZE - 1);
+
+	platform_device_add(&ap325rxa_ceu_device);
+
+	return platform_add_devices(ap325rxa_devices,
+				ARRAY_SIZE(ap325rxa_devices));
+}
+arch_initcall(ap325rxa_devices_setup);
+
+/* Return the board specific boot mode pin configuration */
+static int ap325rxa_mode_pins(void)
+{
+	/* MD0=0, MD1=0, MD2=0: Clock Mode 0
+	 * MD3=0: 16-bit Area0 Bus Width
+	 * MD5=1: Little Endian
+	 * TSTMD=1, MD8=1: Test Mode Disabled
+	 */
+	return MODE_PIN5 | MODE_PIN8;
+}
+
+/* Reserve a portion of memory for CEU buffers */
+static void __init ap325rxa_mv_mem_reserve(void)
+{
+	phys_addr_t phys;
+	phys_addr_t size = CEU_BUFFER_MEMORY_SIZE;
+
+	phys = memblock_phys_alloc(size, PAGE_SIZE);
+	if (!phys)
+		panic("Failed to allocate CEU memory\n");
+
+	memblock_phys_free(phys, size);
+	memblock_remove(phys, size);
+
+	ceu_dma_membase = phys;
+}
+
+static struct sh_machine_vector mv_ap325rxa __initmv = {
+	.mv_name = "AP-325RXA",
+	.mv_mode_pins = ap325rxa_mode_pins,
+	.mv_mem_reserve	= ap325rxa_mv_mem_reserve,
+};