Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 590 insertions, 0 deletions

diff --git a/drivers/gpio/gpio-pcie-idio-24.c b/drivers/gpio/gpio-pcie-idio-24.c
new file mode 100644
index 000000000..8a9b98fa4
--- /dev/null
+++ b/drivers/gpio/gpio-pcie-idio-24.c
@@ -0,0 +1,590 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * GPIO driver for the ACCES PCIe-IDIO-24 family
+ * Copyright (C) 2018 William Breathitt Gray
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * This driver supports the following ACCES devices: PCIe-IDIO-24,
+ * PCIe-IDI-24, PCIe-IDO-24, and PCIe-IDIO-12.
+ */
+#include <linux/bitmap.h>
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/irqdesc.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+/*
+ * PLX PEX8311 PCI LCS_INTCSR Interrupt Control/Status
+ *
+ * Bit: Description
+ *   0: Enable Interrupt Sources (Bit 0)
+ *   1: Enable Interrupt Sources (Bit 1)
+ *   2: Generate Internal PCI Bus Internal SERR# Interrupt
+ *   3: Mailbox Interrupt Enable
+ *   4: Power Management Interrupt Enable
+ *   5: Power Management Interrupt
+ *   6: Slave Read Local Data Parity Check Error Enable
+ *   7: Slave Read Local Data Parity Check Error Status
+ *   8: Internal PCI Wire Interrupt Enable
+ *   9: PCI Express Doorbell Interrupt Enable
+ *  10: PCI Abort Interrupt Enable
+ *  11: Local Interrupt Input Enable
+ *  12: Retry Abort Enable
+ *  13: PCI Express Doorbell Interrupt Active
+ *  14: PCI Abort Interrupt Active
+ *  15: Local Interrupt Input Active
+ *  16: Local Interrupt Output Enable
+ *  17: Local Doorbell Interrupt Enable
+ *  18: DMA Channel 0 Interrupt Enable
+ *  19: DMA Channel 1 Interrupt Enable
+ *  20: Local Doorbell Interrupt Active
+ *  21: DMA Channel 0 Interrupt Active
+ *  22: DMA Channel 1 Interrupt Active
+ *  23: Built-In Self-Test (BIST) Interrupt Active
+ *  24: Direct Master was the Bus Master during a Master or Target Abort
+ *  25: DMA Channel 0 was the Bus Master during a Master or Target Abort
+ *  26: DMA Channel 1 was the Bus Master during a Master or Target Abort
+ *  27: Target Abort after internal 256 consecutive Master Retrys
+ *  28: PCI Bus wrote data to LCS_MBOX0
+ *  29: PCI Bus wrote data to LCS_MBOX1
+ *  30: PCI Bus wrote data to LCS_MBOX2
+ *  31: PCI Bus wrote data to LCS_MBOX3
+ */
+#define PLX_PEX8311_PCI_LCS_INTCSR  0x68
+#define INTCSR_INTERNAL_PCI_WIRE    BIT(8)
+#define INTCSR_LOCAL_INPUT          BIT(11)
+
+/**
+ * struct idio_24_gpio_reg - GPIO device registers structure
+ * @out0_7:	Read: FET Outputs 0-7
+ *		Write: FET Outputs 0-7
+ * @out8_15:	Read: FET Outputs 8-15
+ *		Write: FET Outputs 8-15
+ * @out16_23:	Read: FET Outputs 16-23
+ *		Write: FET Outputs 16-23
+ * @ttl_out0_7:	Read: TTL/CMOS Outputs 0-7
+ *		Write: TTL/CMOS Outputs 0-7
+ * @in0_7:	Read: Isolated Inputs 0-7
+ *		Write: Reserved
+ * @in8_15:	Read: Isolated Inputs 8-15
+ *		Write: Reserved
+ * @in16_23:	Read: Isolated Inputs 16-23
+ *		Write: Reserved
+ * @ttl_in0_7:	Read: TTL/CMOS Inputs 0-7
+ *		Write: Reserved
+ * @cos0_7:	Read: COS Status Inputs 0-7
+ *		Write: COS Clear Inputs 0-7
+ * @cos8_15:	Read: COS Status Inputs 8-15
+ *		Write: COS Clear Inputs 8-15
+ * @cos16_23:	Read: COS Status Inputs 16-23
+ *		Write: COS Clear Inputs 16-23
+ * @cos_ttl0_7:	Read: COS Status TTL/CMOS 0-7
+ *		Write: COS Clear TTL/CMOS 0-7
+ * @ctl:	Read: Control Register
+ *		Write: Control Register
+ * @reserved:	Read: Reserved
+ *		Write: Reserved
+ * @cos_enable:	Read: COS Enable
+ *		Write: COS Enable
+ * @soft_reset:	Read: IRQ Output Pin Status
+ *		Write: Software Board Reset
+ */
+struct idio_24_gpio_reg {
+	u8 out0_7;
+	u8 out8_15;
+	u8 out16_23;
+	u8 ttl_out0_7;
+	u8 in0_7;
+	u8 in8_15;
+	u8 in16_23;
+	u8 ttl_in0_7;
+	u8 cos0_7;
+	u8 cos8_15;
+	u8 cos16_23;
+	u8 cos_ttl0_7;
+	u8 ctl;
+	u8 reserved;
+	u8 cos_enable;
+	u8 soft_reset;
+};
+
+/**
+ * struct idio_24_gpio - GPIO device private data structure
+ * @chip:	instance of the gpio_chip
+ * @lock:	synchronization lock to prevent I/O race conditions
+ * @reg:	I/O address offset for the GPIO device registers
+ * @irq_mask:	I/O bits affected by interrupts
+ */
+struct idio_24_gpio {
+	struct gpio_chip chip;
+	raw_spinlock_t lock;
+	__u8 __iomem *plx;
+	struct idio_24_gpio_reg __iomem *reg;
+	unsigned long irq_mask;
+};
+
+static int idio_24_gpio_get_direction(struct gpio_chip *chip,
+	unsigned int offset)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	const unsigned long out_mode_mask = BIT(1);
+
+	/* FET Outputs */
+	if (offset < 24)
+		return GPIO_LINE_DIRECTION_OUT;
+
+	/* Isolated Inputs */
+	if (offset < 48)
+		return GPIO_LINE_DIRECTION_IN;
+
+	/* TTL/CMOS I/O */
+	/* OUT MODE = 1 when TTL/CMOS Output Mode is set */
+	if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
+		return GPIO_LINE_DIRECTION_OUT;
+
+	return GPIO_LINE_DIRECTION_IN;
+}
+
+static int idio_24_gpio_direction_input(struct gpio_chip *chip,
+	unsigned int offset)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	unsigned int ctl_state;
+	const unsigned long out_mode_mask = BIT(1);
+
+	/* TTL/CMOS I/O */
+	if (offset > 47) {
+		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+		/* Clear TTL/CMOS Output Mode */
+		ctl_state = ioread8(&idio24gpio->reg->ctl) & ~out_mode_mask;
+		iowrite8(ctl_state, &idio24gpio->reg->ctl);
+
+		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	}
+
+	return 0;
+}
+
+static int idio_24_gpio_direction_output(struct gpio_chip *chip,
+	unsigned int offset, int value)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	unsigned int ctl_state;
+	const unsigned long out_mode_mask = BIT(1);
+
+	/* TTL/CMOS I/O */
+	if (offset > 47) {
+		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+		/* Set TTL/CMOS Output Mode */
+		ctl_state = ioread8(&idio24gpio->reg->ctl) | out_mode_mask;
+		iowrite8(ctl_state, &idio24gpio->reg->ctl);
+
+		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	}
+
+	chip->set(chip, offset, value);
+	return 0;
+}
+
+static int idio_24_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	const unsigned long offset_mask = BIT(offset % 8);
+	const unsigned long out_mode_mask = BIT(1);
+
+	/* FET Outputs */
+	if (offset < 8)
+		return !!(ioread8(&idio24gpio->reg->out0_7) & offset_mask);
+
+	if (offset < 16)
+		return !!(ioread8(&idio24gpio->reg->out8_15) & offset_mask);
+
+	if (offset < 24)
+		return !!(ioread8(&idio24gpio->reg->out16_23) & offset_mask);
+
+	/* Isolated Inputs */
+	if (offset < 32)
+		return !!(ioread8(&idio24gpio->reg->in0_7) & offset_mask);
+
+	if (offset < 40)
+		return !!(ioread8(&idio24gpio->reg->in8_15) & offset_mask);
+
+	if (offset < 48)
+		return !!(ioread8(&idio24gpio->reg->in16_23) & offset_mask);
+
+	/* TTL/CMOS Outputs */
+	if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
+		return !!(ioread8(&idio24gpio->reg->ttl_out0_7) & offset_mask);
+
+	/* TTL/CMOS Inputs */
+	return !!(ioread8(&idio24gpio->reg->ttl_in0_7) & offset_mask);
+}
+
+static int idio_24_gpio_get_multiple(struct gpio_chip *chip,
+	unsigned long *mask, unsigned long *bits)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long offset;
+	unsigned long gpio_mask;
+	void __iomem *ports[] = {
+		&idio24gpio->reg->out0_7, &idio24gpio->reg->out8_15,
+		&idio24gpio->reg->out16_23, &idio24gpio->reg->in0_7,
+		&idio24gpio->reg->in8_15, &idio24gpio->reg->in16_23,
+	};
+	size_t index;
+	unsigned long port_state;
+	const unsigned long out_mode_mask = BIT(1);
+
+	/* clear bits array to a clean slate */
+	bitmap_zero(bits, chip->ngpio);
+
+	for_each_set_clump8(offset, gpio_mask, mask, ARRAY_SIZE(ports) * 8) {
+		index = offset / 8;
+
+		/* read bits from current gpio port (port 6 is TTL GPIO) */
+		if (index < 6)
+			port_state = ioread8(ports[index]);
+		else if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask)
+			port_state = ioread8(&idio24gpio->reg->ttl_out0_7);
+		else
+			port_state = ioread8(&idio24gpio->reg->ttl_in0_7);
+
+		port_state &= gpio_mask;
+
+		bitmap_set_value8(bits, port_state, offset);
+	}
+
+	return 0;
+}
+
+static void idio_24_gpio_set(struct gpio_chip *chip, unsigned int offset,
+	int value)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	const unsigned long out_mode_mask = BIT(1);
+	void __iomem *base;
+	const unsigned int mask = BIT(offset % 8);
+	unsigned long flags;
+	unsigned int out_state;
+
+	/* Isolated Inputs */
+	if (offset > 23 && offset < 48)
+		return;
+
+	/* TTL/CMOS Inputs */
+	if (offset > 47 && !(ioread8(&idio24gpio->reg->ctl) & out_mode_mask))
+		return;
+
+	/* TTL/CMOS Outputs */
+	if (offset > 47)
+		base = &idio24gpio->reg->ttl_out0_7;
+	/* FET Outputs */
+	else if (offset > 15)
+		base = &idio24gpio->reg->out16_23;
+	else if (offset > 7)
+		base = &idio24gpio->reg->out8_15;
+	else
+		base = &idio24gpio->reg->out0_7;
+
+	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+	if (value)
+		out_state = ioread8(base) | mask;
+	else
+		out_state = ioread8(base) & ~mask;
+
+	iowrite8(out_state, base);
+
+	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+}
+
+static void idio_24_gpio_set_multiple(struct gpio_chip *chip,
+	unsigned long *mask, unsigned long *bits)
+{
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long offset;
+	unsigned long gpio_mask;
+	void __iomem *ports[] = {
+		&idio24gpio->reg->out0_7, &idio24gpio->reg->out8_15,
+		&idio24gpio->reg->out16_23
+	};
+	size_t index;
+	unsigned long bitmask;
+	unsigned long flags;
+	unsigned long out_state;
+	const unsigned long out_mode_mask = BIT(1);
+
+	for_each_set_clump8(offset, gpio_mask, mask, ARRAY_SIZE(ports) * 8) {
+		index = offset / 8;
+
+		bitmask = bitmap_get_value8(bits, offset) & gpio_mask;
+
+		raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+		/* read bits from current gpio port (port 6 is TTL GPIO) */
+		if (index < 6) {
+			out_state = ioread8(ports[index]);
+		} else if (ioread8(&idio24gpio->reg->ctl) & out_mode_mask) {
+			out_state = ioread8(&idio24gpio->reg->ttl_out0_7);
+		} else {
+			/* skip TTL GPIO if set for input */
+			raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+			continue;
+		}
+
+		/* set requested bit states */
+		out_state &= ~gpio_mask;
+		out_state |= bitmask;
+
+		/* write bits for current gpio port (port 6 is TTL GPIO) */
+		if (index < 6)
+			iowrite8(out_state, ports[index]);
+		else
+			iowrite8(out_state, &idio24gpio->reg->ttl_out0_7);
+
+		raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+	}
+}
+
+static void idio_24_irq_ack(struct irq_data *data)
+{
+}
+
+static void idio_24_irq_mask(struct irq_data *data)
+{
+	struct gpio_chip *const chip = irq_data_get_irq_chip_data(data);
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	const unsigned long bit_offset = irqd_to_hwirq(data) - 24;
+	unsigned char new_irq_mask;
+	const unsigned long bank_offset = bit_offset / 8;
+	unsigned char cos_enable_state;
+
+	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+	idio24gpio->irq_mask &= ~BIT(bit_offset);
+	new_irq_mask = idio24gpio->irq_mask >> bank_offset * 8;
+
+	if (!new_irq_mask) {
+		cos_enable_state = ioread8(&idio24gpio->reg->cos_enable);
+
+		/* Disable Rising Edge detection */
+		cos_enable_state &= ~BIT(bank_offset);
+		/* Disable Falling Edge detection */
+		cos_enable_state &= ~BIT(bank_offset + 4);
+
+		iowrite8(cos_enable_state, &idio24gpio->reg->cos_enable);
+	}
+
+	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+}
+
+static void idio_24_irq_unmask(struct irq_data *data)
+{
+	struct gpio_chip *const chip = irq_data_get_irq_chip_data(data);
+	struct idio_24_gpio *const idio24gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	unsigned char prev_irq_mask;
+	const unsigned long bit_offset = irqd_to_hwirq(data) - 24;
+	const unsigned long bank_offset = bit_offset / 8;
+	unsigned char cos_enable_state;
+
+	raw_spin_lock_irqsave(&idio24gpio->lock, flags);
+
+	prev_irq_mask = idio24gpio->irq_mask >> bank_offset * 8;
+	idio24gpio->irq_mask |= BIT(bit_offset);
+
+	if (!prev_irq_mask) {
+		cos_enable_state = ioread8(&idio24gpio->reg->cos_enable);
+
+		/* Enable Rising Edge detection */
+		cos_enable_state |= BIT(bank_offset);
+		/* Enable Falling Edge detection */
+		cos_enable_state |= BIT(bank_offset + 4);
+
+		iowrite8(cos_enable_state, &idio24gpio->reg->cos_enable);
+	}
+
+	raw_spin_unlock_irqrestore(&idio24gpio->lock, flags);
+}
+
+static int idio_24_irq_set_type(struct irq_data *data, unsigned int flow_type)
+{
+	/* The only valid irq types are none and both-edges */
+	if (flow_type != IRQ_TYPE_NONE &&
+		(flow_type & IRQ_TYPE_EDGE_BOTH) != IRQ_TYPE_EDGE_BOTH)
+		return -EINVAL;
+
+	return 0;
+}
+
+static struct irq_chip idio_24_irqchip = {
+	.name = "pcie-idio-24",
+	.irq_ack = idio_24_irq_ack,
+	.irq_mask = idio_24_irq_mask,
+	.irq_unmask = idio_24_irq_unmask,
+	.irq_set_type = idio_24_irq_set_type
+};
+
+static irqreturn_t idio_24_irq_handler(int irq, void *dev_id)
+{
+	struct idio_24_gpio *const idio24gpio = dev_id;
+	unsigned long irq_status;
+	struct gpio_chip *const chip = &idio24gpio->chip;
+	unsigned long irq_mask;
+	int gpio;
+
+	raw_spin_lock(&idio24gpio->lock);
+
+	/* Read Change-Of-State status */
+	irq_status = ioread32(&idio24gpio->reg->cos0_7);
+
+	raw_spin_unlock(&idio24gpio->lock);
+
+	/* Make sure our device generated IRQ */
+	if (!irq_status)
+		return IRQ_NONE;
+
+	/* Handle only unmasked IRQ */
+	irq_mask = idio24gpio->irq_mask & irq_status;
+
+	for_each_set_bit(gpio, &irq_mask, chip->ngpio - 24)
+		generic_handle_domain_irq(chip->irq.domain, gpio + 24);
+
+	raw_spin_lock(&idio24gpio->lock);
+
+	/* Clear Change-Of-State status */
+	iowrite32(irq_status, &idio24gpio->reg->cos0_7);
+
+	raw_spin_unlock(&idio24gpio->lock);
+
+	return IRQ_HANDLED;
+}
+
+#define IDIO_24_NGPIO 56
+static const char *idio_24_names[IDIO_24_NGPIO] = {
+	"OUT0", "OUT1", "OUT2", "OUT3", "OUT4", "OUT5", "OUT6", "OUT7",
+	"OUT8", "OUT9", "OUT10", "OUT11", "OUT12", "OUT13", "OUT14", "OUT15",
+	"OUT16", "OUT17", "OUT18", "OUT19", "OUT20", "OUT21", "OUT22", "OUT23",
+	"IIN0", "IIN1", "IIN2", "IIN3", "IIN4", "IIN5", "IIN6", "IIN7",
+	"IIN8", "IIN9", "IIN10", "IIN11", "IIN12", "IIN13", "IIN14", "IIN15",
+	"IIN16", "IIN17", "IIN18", "IIN19", "IIN20", "IIN21", "IIN22", "IIN23",
+	"TTL0", "TTL1", "TTL2", "TTL3", "TTL4", "TTL5", "TTL6", "TTL7"
+};
+
+static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct device *const dev = &pdev->dev;
+	struct idio_24_gpio *idio24gpio;
+	int err;
+	const size_t pci_plx_bar_index = 1;
+	const size_t pci_bar_index = 2;
+	const char *const name = pci_name(pdev);
+	struct gpio_irq_chip *girq;
+
+	idio24gpio = devm_kzalloc(dev, sizeof(*idio24gpio), GFP_KERNEL);
+	if (!idio24gpio)
+		return -ENOMEM;
+
+	err = pcim_enable_device(pdev);
+	if (err) {
+		dev_err(dev, "Failed to enable PCI device (%d)\n", err);
+		return err;
+	}
+
+	err = pcim_iomap_regions(pdev, BIT(pci_plx_bar_index) | BIT(pci_bar_index), name);
+	if (err) {
+		dev_err(dev, "Unable to map PCI I/O addresses (%d)\n", err);
+		return err;
+	}
+
+	idio24gpio->plx = pcim_iomap_table(pdev)[pci_plx_bar_index];
+	idio24gpio->reg = pcim_iomap_table(pdev)[pci_bar_index];
+
+	idio24gpio->chip.label = name;
+	idio24gpio->chip.parent = dev;
+	idio24gpio->chip.owner = THIS_MODULE;
+	idio24gpio->chip.base = -1;
+	idio24gpio->chip.ngpio = IDIO_24_NGPIO;
+	idio24gpio->chip.names = idio_24_names;
+	idio24gpio->chip.get_direction = idio_24_gpio_get_direction;
+	idio24gpio->chip.direction_input = idio_24_gpio_direction_input;
+	idio24gpio->chip.direction_output = idio_24_gpio_direction_output;
+	idio24gpio->chip.get = idio_24_gpio_get;
+	idio24gpio->chip.get_multiple = idio_24_gpio_get_multiple;
+	idio24gpio->chip.set = idio_24_gpio_set;
+	idio24gpio->chip.set_multiple = idio_24_gpio_set_multiple;
+
+	girq = &idio24gpio->chip.irq;
+	girq->chip = &idio_24_irqchip;
+	/* This will let us handle the parent IRQ in the driver */
+	girq->parent_handler = NULL;
+	girq->num_parents = 0;
+	girq->parents = NULL;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_edge_irq;
+
+	raw_spin_lock_init(&idio24gpio->lock);
+
+	/* Software board reset */
+	iowrite8(0, &idio24gpio->reg->soft_reset);
+	/*
+	 * enable PLX PEX8311 internal PCI wire interrupt and local interrupt
+	 * input
+	 */
+	iowrite8((INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT) >> 8,
+		 idio24gpio->plx + PLX_PEX8311_PCI_LCS_INTCSR + 1);
+
+	err = devm_gpiochip_add_data(dev, &idio24gpio->chip, idio24gpio);
+	if (err) {
+		dev_err(dev, "GPIO registering failed (%d)\n", err);
+		return err;
+	}
+
+	err = devm_request_irq(dev, pdev->irq, idio_24_irq_handler, IRQF_SHARED,
+		name, idio24gpio);
+	if (err) {
+		dev_err(dev, "IRQ handler registering failed (%d)\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static const struct pci_device_id idio_24_pci_dev_id[] = {
+	{ PCI_DEVICE(0x494F, 0x0FD0) }, { PCI_DEVICE(0x494F, 0x0BD0) },
+	{ PCI_DEVICE(0x494F, 0x07D0) }, { PCI_DEVICE(0x494F, 0x0FC0) },
+	{ 0 }
+};
+MODULE_DEVICE_TABLE(pci, idio_24_pci_dev_id);
+
+static struct pci_driver idio_24_driver = {
+	.name = "pcie-idio-24",
+	.id_table = idio_24_pci_dev_id,
+	.probe = idio_24_probe
+};
+
+module_pci_driver(idio_24_driver);
+
+MODULE_AUTHOR("William Breathitt Gray <vilhelm.gray@gmail.com>");
+MODULE_DESCRIPTION("ACCES PCIe-IDIO-24 GPIO driver");
+MODULE_LICENSE("GPL v2");