Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 509 insertions, 0 deletions

diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c
new file mode 100644
index 000000000..cc58feacd
--- /dev/null
+++ b/drivers/i2c/busses/i2c-ali15x3.c
@@ -0,0 +1,509 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+    Copyright (c) 1999  Frodo Looijaard <frodol@dds.nl> and
+    Philip Edelbrock <phil@netroedge.com> and
+    Mark D. Studebaker <mdsxyz123@yahoo.com>
+
+*/
+
+/*
+    This is the driver for the SMB Host controller on
+    Acer Labs Inc. (ALI) M1541 and M1543C South Bridges.
+
+    The M1543C is a South bridge for desktop systems.
+    The M1533 is a South bridge for portable systems.
+    They are part of the following ALI chipsets:
+       "Aladdin Pro 2": Includes the M1621 Slot 1 North bridge
+       with AGP and 100MHz CPU Front Side bus
+       "Aladdin V": Includes the M1541 Socket 7 North bridge
+       with AGP and 100MHz CPU Front Side bus
+       "Aladdin IV": Includes the M1541 Socket 7 North bridge
+       with host bus up to 83.3 MHz.
+    For an overview of these chips see http://www.acerlabs.com
+
+    The M1533/M1543C devices appear as FOUR separate devices
+    on the PCI bus. An output of lspci will show something similar
+    to the following:
+
+	00:02.0 USB Controller: Acer Laboratories Inc. M5237
+	00:03.0 Bridge: Acer Laboratories Inc. M7101
+	00:07.0 ISA bridge: Acer Laboratories Inc. M1533
+	00:0f.0 IDE interface: Acer Laboratories Inc. M5229
+
+    The SMB controller is part of the 7101 device, which is an
+    ACPI-compliant Power Management Unit (PMU).
+
+    The whole 7101 device has to be enabled for the SMB to work.
+    You can't just enable the SMB alone.
+    The SMB and the ACPI have separate I/O spaces.
+    We make sure that the SMB is enabled. We leave the ACPI alone.
+
+    This driver controls the SMB Host only.
+    The SMB Slave controller on the M15X3 is not enabled.
+
+    This driver does not use interrupts.
+*/
+
+/* Note: we assume there can only be one ALI15X3, with one SMBus interface */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/stddef.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/acpi.h>
+#include <linux/io.h>
+
+/* ALI15X3 SMBus address offsets */
+#define SMBHSTSTS	(0 + ali15x3_smba)
+#define SMBHSTCNT	(1 + ali15x3_smba)
+#define SMBHSTSTART	(2 + ali15x3_smba)
+#define SMBHSTCMD	(7 + ali15x3_smba)
+#define SMBHSTADD	(3 + ali15x3_smba)
+#define SMBHSTDAT0	(4 + ali15x3_smba)
+#define SMBHSTDAT1	(5 + ali15x3_smba)
+#define SMBBLKDAT	(6 + ali15x3_smba)
+
+/* PCI Address Constants */
+#define SMBCOM		0x004
+#define SMBBA		0x014
+#define SMBATPC		0x05B	/* used to unlock xxxBA registers */
+#define SMBHSTCFG	0x0E0
+#define SMBSLVC		0x0E1
+#define SMBCLK		0x0E2
+#define SMBREV		0x008
+
+/* Other settings */
+#define MAX_TIMEOUT		200	/* times 1/100 sec */
+#define ALI15X3_SMB_IOSIZE	32
+
+/* this is what the Award 1004 BIOS sets them to on a ASUS P5A MB.
+   We don't use these here. If the bases aren't set to some value we
+   tell user to upgrade BIOS and we fail.
+*/
+#define ALI15X3_SMB_DEFAULTBASE	0xE800
+
+/* ALI15X3 address lock bits */
+#define ALI15X3_LOCK		0x06
+
+/* ALI15X3 command constants */
+#define ALI15X3_ABORT		0x02
+#define ALI15X3_T_OUT		0x04
+#define ALI15X3_QUICK		0x00
+#define ALI15X3_BYTE		0x10
+#define ALI15X3_BYTE_DATA	0x20
+#define ALI15X3_WORD_DATA	0x30
+#define ALI15X3_BLOCK_DATA	0x40
+#define ALI15X3_BLOCK_CLR	0x80
+
+/* ALI15X3 status register bits */
+#define ALI15X3_STS_IDLE	0x04
+#define ALI15X3_STS_BUSY	0x08
+#define ALI15X3_STS_DONE	0x10
+#define ALI15X3_STS_DEV		0x20	/* device error */
+#define ALI15X3_STS_COLL	0x40	/* collision or no response */
+#define ALI15X3_STS_TERM	0x80	/* terminated by abort */
+#define ALI15X3_STS_ERR		0xE0	/* all the bad error bits */
+
+
+/* If force_addr is set to anything different from 0, we forcibly enable
+   the device at the given address. */
+static u16 force_addr;
+module_param_hw(force_addr, ushort, ioport, 0);
+MODULE_PARM_DESC(force_addr,
+		 "Initialize the base address of the i2c controller");
+
+static struct pci_driver ali15x3_driver;
+static unsigned short ali15x3_smba;
+
+static int ali15x3_setup(struct pci_dev *ALI15X3_dev)
+{
+	u16 a;
+	unsigned char temp;
+
+	/* Check the following things:
+		- SMB I/O address is initialized
+		- Device is enabled
+		- We can use the addresses
+	*/
+
+	/* Unlock the register.
+	   The data sheet says that the address registers are read-only
+	   if the lock bits are 1, but in fact the address registers
+	   are zero unless you clear the lock bits.
+	*/
+	pci_read_config_byte(ALI15X3_dev, SMBATPC, &temp);
+	if (temp & ALI15X3_LOCK) {
+		temp &= ~ALI15X3_LOCK;
+		pci_write_config_byte(ALI15X3_dev, SMBATPC, temp);
+	}
+
+	/* Determine the address of the SMBus area */
+	pci_read_config_word(ALI15X3_dev, SMBBA, &ali15x3_smba);
+	ali15x3_smba &= (0xffff & ~(ALI15X3_SMB_IOSIZE - 1));
+	if (ali15x3_smba == 0 && force_addr == 0) {
+		dev_err(&ALI15X3_dev->dev, "ALI15X3_smb region uninitialized "
+			"- upgrade BIOS or use force_addr=0xaddr\n");
+		return -ENODEV;
+	}
+
+	if(force_addr)
+		ali15x3_smba = force_addr & ~(ALI15X3_SMB_IOSIZE - 1);
+
+	if (acpi_check_region(ali15x3_smba, ALI15X3_SMB_IOSIZE,
+			      ali15x3_driver.name))
+		return -EBUSY;
+
+	if (!request_region(ali15x3_smba, ALI15X3_SMB_IOSIZE,
+			    ali15x3_driver.name)) {
+		dev_err(&ALI15X3_dev->dev,
+			"ALI15X3_smb region 0x%x already in use!\n",
+			ali15x3_smba);
+		return -ENODEV;
+	}
+
+	if(force_addr) {
+		dev_info(&ALI15X3_dev->dev, "forcing ISA address 0x%04X\n",
+			ali15x3_smba);
+		if (PCIBIOS_SUCCESSFUL != pci_write_config_word(ALI15X3_dev,
+								SMBBA,
+								ali15x3_smba))
+			goto error;
+		if (PCIBIOS_SUCCESSFUL != pci_read_config_word(ALI15X3_dev,
+								SMBBA, &a))
+			goto error;
+		if ((a & ~(ALI15X3_SMB_IOSIZE - 1)) != ali15x3_smba) {
+			/* make sure it works */
+			dev_err(&ALI15X3_dev->dev,
+				"force address failed - not supported?\n");
+			goto error;
+		}
+	}
+	/* check if whole device is enabled */
+	pci_read_config_byte(ALI15X3_dev, SMBCOM, &temp);
+	if ((temp & 1) == 0) {
+		dev_info(&ALI15X3_dev->dev, "enabling SMBus device\n");
+		pci_write_config_byte(ALI15X3_dev, SMBCOM, temp | 0x01);
+	}
+
+	/* Is SMB Host controller enabled? */
+	pci_read_config_byte(ALI15X3_dev, SMBHSTCFG, &temp);
+	if ((temp & 1) == 0) {
+		dev_info(&ALI15X3_dev->dev, "enabling SMBus controller\n");
+		pci_write_config_byte(ALI15X3_dev, SMBHSTCFG, temp | 0x01);
+	}
+
+	/* set SMB clock to 74KHz as recommended in data sheet */
+	pci_write_config_byte(ALI15X3_dev, SMBCLK, 0x20);
+
+	/*
+	  The interrupt routing for SMB is set up in register 0x77 in the
+	  1533 ISA Bridge device, NOT in the 7101 device.
+	  Don't bother with finding the 1533 device and reading the register.
+	if ((....... & 0x0F) == 1)
+		dev_dbg(&ALI15X3_dev->dev, "ALI15X3 using Interrupt 9 for SMBus.\n");
+	*/
+	pci_read_config_byte(ALI15X3_dev, SMBREV, &temp);
+	dev_dbg(&ALI15X3_dev->dev, "SMBREV = 0x%X\n", temp);
+	dev_dbg(&ALI15X3_dev->dev, "iALI15X3_smba = 0x%X\n", ali15x3_smba);
+
+	return 0;
+error:
+	release_region(ali15x3_smba, ALI15X3_SMB_IOSIZE);
+	return -ENODEV;
+}
+
+/* Another internally used function */
+static int ali15x3_transaction(struct i2c_adapter *adap)
+{
+	int temp;
+	int result = 0;
+	int timeout = 0;
+
+	dev_dbg(&adap->dev, "Transaction (pre): STS=%02x, CNT=%02x, CMD=%02x, "
+		"ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTSTS),
+		inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD),
+		inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1));
+
+	/* get status */
+	temp = inb_p(SMBHSTSTS);
+
+	/* Make sure the SMBus host is ready to start transmitting */
+	/* Check the busy bit first */
+	if (temp & ALI15X3_STS_BUSY) {
+	/*
+	   If the host controller is still busy, it may have timed out in the
+	   previous transaction, resulting in a "SMBus Timeout" Dev.
+	   I've tried the following to reset a stuck busy bit.
+		1. Reset the controller with an ABORT command.
+		   (this doesn't seem to clear the controller if an external
+		   device is hung)
+		2. Reset the controller and the other SMBus devices with a
+		   T_OUT command.  (this clears the host busy bit if an
+		   external device is hung, but it comes back upon a new access
+		   to a device)
+		3. Disable and reenable the controller in SMBHSTCFG
+	   Worst case, nothing seems to work except power reset.
+	*/
+	/* Abort - reset the host controller */
+	/*
+	   Try resetting entire SMB bus, including other devices -
+	   This may not work either - it clears the BUSY bit but
+	   then the BUSY bit may come back on when you try and use the chip again.
+	   If that's the case you are stuck.
+	*/
+		dev_info(&adap->dev, "Resetting entire SMB Bus to "
+			"clear busy condition (%02x)\n", temp);
+		outb_p(ALI15X3_T_OUT, SMBHSTCNT);
+		temp = inb_p(SMBHSTSTS);
+	}
+
+	/* now check the error bits and the busy bit */
+	if (temp & (ALI15X3_STS_ERR | ALI15X3_STS_BUSY)) {
+		/* do a clear-on-write */
+		outb_p(0xFF, SMBHSTSTS);
+		if ((temp = inb_p(SMBHSTSTS)) &
+		    (ALI15X3_STS_ERR | ALI15X3_STS_BUSY)) {
+			/* this is probably going to be correctable only by a power reset
+			   as one of the bits now appears to be stuck */
+			/* This may be a bus or device with electrical problems. */
+			dev_err(&adap->dev, "SMBus reset failed! (0x%02x) - "
+				"controller or device on bus is probably hung\n",
+				temp);
+			return -EBUSY;
+		}
+	} else {
+		/* check and clear done bit */
+		if (temp & ALI15X3_STS_DONE) {
+			outb_p(temp, SMBHSTSTS);
+		}
+	}
+
+	/* start the transaction by writing anything to the start register */
+	outb_p(0xFF, SMBHSTSTART);
+
+	/* We will always wait for a fraction of a second! */
+	timeout = 0;
+	do {
+		msleep(1);
+		temp = inb_p(SMBHSTSTS);
+	} while ((!(temp & (ALI15X3_STS_ERR | ALI15X3_STS_DONE)))
+		 && (timeout++ < MAX_TIMEOUT));
+
+	/* If the SMBus is still busy, we give up */
+	if (timeout > MAX_TIMEOUT) {
+		result = -ETIMEDOUT;
+		dev_err(&adap->dev, "SMBus Timeout!\n");
+	}
+
+	if (temp & ALI15X3_STS_TERM) {
+		result = -EIO;
+		dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
+	}
+
+	/*
+	  Unfortunately the ALI SMB controller maps "no response" and "bus
+	  collision" into a single bit. No response is the usual case so don't
+	  do a printk.
+	  This means that bus collisions go unreported.
+	*/
+	if (temp & ALI15X3_STS_COLL) {
+		result = -ENXIO;
+		dev_dbg(&adap->dev,
+			"Error: no response or bus collision ADD=%02x\n",
+			inb_p(SMBHSTADD));
+	}
+
+	/* haven't ever seen this */
+	if (temp & ALI15X3_STS_DEV) {
+		result = -EIO;
+		dev_err(&adap->dev, "Error: device error\n");
+	}
+	dev_dbg(&adap->dev, "Transaction (post): STS=%02x, CNT=%02x, CMD=%02x, "
+		"ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTSTS),
+		inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD),
+		inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1));
+	return result;
+}
+
+/* Return negative errno on error. */
+static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr,
+		   unsigned short flags, char read_write, u8 command,
+		   int size, union i2c_smbus_data * data)
+{
+	int i, len;
+	int temp;
+	int timeout;
+
+	/* clear all the bits (clear-on-write) */
+	outb_p(0xFF, SMBHSTSTS);
+	/* make sure SMBus is idle */
+	temp = inb_p(SMBHSTSTS);
+	for (timeout = 0;
+	     (timeout < MAX_TIMEOUT) && !(temp & ALI15X3_STS_IDLE);
+	     timeout++) {
+		msleep(1);
+		temp = inb_p(SMBHSTSTS);
+	}
+	if (timeout >= MAX_TIMEOUT) {
+		dev_err(&adap->dev, "Idle wait Timeout! STS=0x%02x\n", temp);
+	}
+
+	switch (size) {
+	case I2C_SMBUS_QUICK:
+		outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
+		       SMBHSTADD);
+		size = ALI15X3_QUICK;
+		break;
+	case I2C_SMBUS_BYTE:
+		outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
+		       SMBHSTADD);
+		if (read_write == I2C_SMBUS_WRITE)
+			outb_p(command, SMBHSTCMD);
+		size = ALI15X3_BYTE;
+		break;
+	case I2C_SMBUS_BYTE_DATA:
+		outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
+		       SMBHSTADD);
+		outb_p(command, SMBHSTCMD);
+		if (read_write == I2C_SMBUS_WRITE)
+			outb_p(data->byte, SMBHSTDAT0);
+		size = ALI15X3_BYTE_DATA;
+		break;
+	case I2C_SMBUS_WORD_DATA:
+		outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
+		       SMBHSTADD);
+		outb_p(command, SMBHSTCMD);
+		if (read_write == I2C_SMBUS_WRITE) {
+			outb_p(data->word & 0xff, SMBHSTDAT0);
+			outb_p((data->word & 0xff00) >> 8, SMBHSTDAT1);
+		}
+		size = ALI15X3_WORD_DATA;
+		break;
+	case I2C_SMBUS_BLOCK_DATA:
+		outb_p(((addr & 0x7f) << 1) | (read_write & 0x01),
+		       SMBHSTADD);
+		outb_p(command, SMBHSTCMD);
+		if (read_write == I2C_SMBUS_WRITE) {
+			len = data->block[0];
+			if (len < 0) {
+				len = 0;
+				data->block[0] = len;
+			}
+			if (len > 32) {
+				len = 32;
+				data->block[0] = len;
+			}
+			outb_p(len, SMBHSTDAT0);
+			/* Reset SMBBLKDAT */
+			outb_p(inb_p(SMBHSTCNT) | ALI15X3_BLOCK_CLR, SMBHSTCNT);
+			for (i = 1; i <= len; i++)
+				outb_p(data->block[i], SMBBLKDAT);
+		}
+		size = ALI15X3_BLOCK_DATA;
+		break;
+	default:
+		dev_warn(&adap->dev, "Unsupported transaction %d\n", size);
+		return -EOPNOTSUPP;
+	}
+
+	outb_p(size, SMBHSTCNT);	/* output command */
+
+	temp = ali15x3_transaction(adap);
+	if (temp)
+		return temp;
+
+	if ((read_write == I2C_SMBUS_WRITE) || (size == ALI15X3_QUICK))
+		return 0;
+
+
+	switch (size) {
+	case ALI15X3_BYTE:	/* Result put in SMBHSTDAT0 */
+		data->byte = inb_p(SMBHSTDAT0);
+		break;
+	case ALI15X3_BYTE_DATA:
+		data->byte = inb_p(SMBHSTDAT0);
+		break;
+	case ALI15X3_WORD_DATA:
+		data->word = inb_p(SMBHSTDAT0) + (inb_p(SMBHSTDAT1) << 8);
+		break;
+	case ALI15X3_BLOCK_DATA:
+		len = inb_p(SMBHSTDAT0);
+		if (len > 32)
+			len = 32;
+		data->block[0] = len;
+		/* Reset SMBBLKDAT */
+		outb_p(inb_p(SMBHSTCNT) | ALI15X3_BLOCK_CLR, SMBHSTCNT);
+		for (i = 1; i <= data->block[0]; i++) {
+			data->block[i] = inb_p(SMBBLKDAT);
+			dev_dbg(&adap->dev, "Blk: len=%d, i=%d, data=%02x\n",
+				len, i, data->block[i]);
+		}
+		break;
+	}
+	return 0;
+}
+
+static u32 ali15x3_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
+	    I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+	    I2C_FUNC_SMBUS_BLOCK_DATA;
+}
+
+static const struct i2c_algorithm smbus_algorithm = {
+	.smbus_xfer	= ali15x3_access,
+	.functionality	= ali15x3_func,
+};
+
+static struct i2c_adapter ali15x3_adapter = {
+	.owner		= THIS_MODULE,
+	.class          = I2C_CLASS_HWMON | I2C_CLASS_SPD,
+	.algo		= &smbus_algorithm,
+};
+
+static const struct pci_device_id ali15x3_ids[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) },
+	{ 0, }
+};
+
+MODULE_DEVICE_TABLE (pci, ali15x3_ids);
+
+static int ali15x3_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	if (ali15x3_setup(dev)) {
+		dev_err(&dev->dev,
+			"ALI15X3 not detected, module not inserted.\n");
+		return -ENODEV;
+	}
+
+	/* set up the sysfs linkage to our parent device */
+	ali15x3_adapter.dev.parent = &dev->dev;
+
+	snprintf(ali15x3_adapter.name, sizeof(ali15x3_adapter.name),
+		"SMBus ALI15X3 adapter at %04x", ali15x3_smba);
+	return i2c_add_adapter(&ali15x3_adapter);
+}
+
+static void ali15x3_remove(struct pci_dev *dev)
+{
+	i2c_del_adapter(&ali15x3_adapter);
+	release_region(ali15x3_smba, ALI15X3_SMB_IOSIZE);
+}
+
+static struct pci_driver ali15x3_driver = {
+	.name		= "ali15x3_smbus",
+	.id_table	= ali15x3_ids,
+	.probe		= ali15x3_probe,
+	.remove		= ali15x3_remove,
+};
+
+module_pci_driver(ali15x3_driver);
+
+MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>");
+MODULE_AUTHOR("Philip Edelbrock <phil@netroedge.com>");
+MODULE_AUTHOR("Mark D. Studebaker <mdsxyz123@yahoo.com>");
+MODULE_DESCRIPTION("ALI15X3 SMBus driver");
+MODULE_LICENSE("GPL");