Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

1 files changed, 542 insertions, 0 deletions

diff --git a/drivers/net/wireless/ti/wl12xx/reg.h b/drivers/net/wireless/ti/wl12xx/reg.h
new file mode 100644
index 000000000..8ff018808
--- /dev/null
+++ b/drivers/net/wireless/ti/wl12xx/reg.h
@@ -0,0 +1,542 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (C) 1998-2009 Texas Instruments. All rights reserved.
+ * Copyright (C) 2009 Nokia Corporation
+ *
+ * Contact: Luciano Coelho <luciano.coelho@nokia.com>
+ */
+
+#ifndef __REG_H__
+#define __REG_H__
+
+#include <linux/bitops.h>
+
+#define REGISTERS_BASE 0x00300000
+#define DRPW_BASE      0x00310000
+
+#define REGISTERS_DOWN_SIZE 0x00008800
+#define REGISTERS_WORK_SIZE 0x0000b000
+
+#define FW_STATUS_ADDR                      (0x14FC0 + 0xA000)
+
+/*===============================================
+   Host Software Reset - 32bit RW
+ ------------------------------------------
+    [31:1] Reserved
+    0  SOFT_RESET Soft Reset  - When this bit is set,
+    it holds the Wlan hardware in a soft reset state.
+    This reset disables all MAC and baseband processor
+    clocks except the CardBus/PCI interface clock.
+    It also initializes all MAC state machines except
+    the host interface. It does not reload the
+    contents of the EEPROM. When this bit is cleared
+    (not self-clearing), the Wlan hardware
+    exits the software reset state.
+===============================================*/
+#define WL12XX_SLV_SOFT_RESET		(REGISTERS_BASE + 0x0000)
+
+#define WL1271_SLV_REG_DATA            (REGISTERS_BASE + 0x0008)
+#define WL1271_SLV_REG_ADATA           (REGISTERS_BASE + 0x000c)
+#define WL1271_SLV_MEM_DATA            (REGISTERS_BASE + 0x0018)
+
+#define WL12XX_REG_INTERRUPT_TRIG         (REGISTERS_BASE + 0x0474)
+#define WL12XX_REG_INTERRUPT_TRIG_H       (REGISTERS_BASE + 0x0478)
+
+/*=============================================
+  Host Interrupt Mask Register - 32bit (RW)
+  ------------------------------------------
+  Setting a bit in this register masks the
+  corresponding interrupt to the host.
+  0 - RX0		- Rx first dubble buffer Data Interrupt
+  1 - TXD		- Tx Data Interrupt
+  2 - TXXFR		- Tx Transfer Interrupt
+  3 - RX1		- Rx second dubble buffer Data Interrupt
+  4 - RXXFR		- Rx Transfer Interrupt
+  5 - EVENT_A	- Event Mailbox interrupt
+  6 - EVENT_B	- Event Mailbox interrupt
+  7 - WNONHST	- Wake On Host Interrupt
+  8 - TRACE_A	- Debug Trace interrupt
+  9 - TRACE_B	- Debug Trace interrupt
+ 10 - CDCMP		- Command Complete Interrupt
+ 11 -
+ 12 -
+ 13 -
+ 14 - ICOMP		- Initialization Complete Interrupt
+ 16 - SG SE		- Soft Gemini - Sense enable interrupt
+ 17 - SG SD		- Soft Gemini - Sense disable interrupt
+ 18 -			-
+ 19 -			-
+ 20 -			-
+ 21-			-
+ Default: 0x0001
+*==============================================*/
+#define WL12XX_REG_INTERRUPT_MASK         (REGISTERS_BASE + 0x04DC)
+
+/*=============================================
+  Host Interrupt Mask Set 16bit, (Write only)
+  ------------------------------------------
+ Setting a bit in this register sets
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+==============================================*/
+#define ACX_REG_HINT_MASK_SET          (REGISTERS_BASE + 0x04E0)
+
+/*=============================================
+  Host Interrupt Mask Clear 16bit,(Write only)
+  ------------------------------------------
+ Setting a bit in this register clears
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+=============================================*/
+#define ACX_REG_HINT_MASK_CLR          (REGISTERS_BASE + 0x04E4)
+
+/*=============================================
+  Host Interrupt Status Nondestructive Read
+  16bit,(Read only)
+  ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register doesn't
+ effect its content.
+=============================================*/
+#define WL12XX_REG_INTERRUPT_NO_CLEAR     (REGISTERS_BASE + 0x04E8)
+
+/*=============================================
+  Host Interrupt Status Clear on Read  Register
+  16bit,(Read only)
+  ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register clears it,
+ thus making all interrupts inactive.
+==============================================*/
+#define ACX_REG_INTERRUPT_CLEAR        (REGISTERS_BASE + 0x04F8)
+
+/*=============================================
+  Host Interrupt Acknowledge Register
+  16bit,(Write only)
+  ------------------------------------------
+ The host can set individual bits in this
+ register to clear (acknowledge) the corresp.
+ interrupt status bits in the HINT_STS_CLR and
+ HINT_STS_ND registers, thus making the
+ assotiated interrupt inactive. (0-no effect)
+==============================================*/
+#define WL12XX_REG_INTERRUPT_ACK          (REGISTERS_BASE + 0x04F0)
+
+#define WL12XX_REG_RX_DRIVER_COUNTER	(REGISTERS_BASE + 0x0538)
+
+/* Device Configuration registers*/
+#define SOR_CFG                        (REGISTERS_BASE + 0x0800)
+
+/* Embedded ARM CPU Control */
+
+/*===============================================
+ Halt eCPU   - 32bit RW
+ ------------------------------------------
+ 0 HALT_ECPU Halt Embedded CPU - This bit is the
+ complement of bit 1 (MDATA2) in the SOR_CFG register.
+ During a hardware reset, this bit holds
+ the inverse of MDATA2.
+ When downloading firmware from the host,
+ set this bit (pull down MDATA2).
+ The host clears this bit after downloading the firmware into
+ zero-wait-state SSRAM.
+ When loading firmware from Flash, clear this bit (pull up MDATA2)
+ so that the eCPU can run the bootloader code in Flash
+ HALT_ECPU eCPU State
+ --------------------
+ 1 halt eCPU
+ 0 enable eCPU
+ ===============================================*/
+#define WL12XX_REG_ECPU_CONTROL           (REGISTERS_BASE + 0x0804)
+
+#define WL12XX_HI_CFG			(REGISTERS_BASE + 0x0808)
+
+/*===============================================
+ EEPROM Burst Read Start  - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0  ACX_EE_START -  EEPROM Burst Read Start 0
+ Setting this bit starts a burst read from
+ the external EEPROM.
+ If this bit is set (after reset) before an EEPROM read/write,
+ the burst read starts at EEPROM address 0.
+ Otherwise, it starts at the address
+ following the address of the previous access.
+ TheWlan hardware hardware clears this bit automatically.
+
+ Default: 0x00000000
+*================================================*/
+#define ACX_REG_EE_START               (REGISTERS_BASE + 0x080C)
+
+#define WL12XX_OCP_POR_CTR		(REGISTERS_BASE + 0x09B4)
+#define WL12XX_OCP_DATA_WRITE		(REGISTERS_BASE + 0x09B8)
+#define WL12XX_OCP_DATA_READ		(REGISTERS_BASE + 0x09BC)
+#define WL12XX_OCP_CMD			(REGISTERS_BASE + 0x09C0)
+
+#define WL12XX_HOST_WR_ACCESS		(REGISTERS_BASE + 0x09F8)
+
+#define WL12XX_CHIP_ID_B		(REGISTERS_BASE + 0x5674)
+
+#define WL12XX_ENABLE			(REGISTERS_BASE + 0x5450)
+
+/* Power Management registers */
+#define WL12XX_ELP_CFG_MODE		(REGISTERS_BASE + 0x5804)
+#define WL12XX_ELP_CMD			(REGISTERS_BASE + 0x5808)
+#define WL12XX_PLL_CAL_TIME		(REGISTERS_BASE + 0x5810)
+#define WL12XX_CLK_REQ_TIME		(REGISTERS_BASE + 0x5814)
+#define WL12XX_CLK_BUF_TIME		(REGISTERS_BASE + 0x5818)
+
+#define WL12XX_CFG_PLL_SYNC_CNT		(REGISTERS_BASE + 0x5820)
+
+/* Scratch Pad registers*/
+#define WL12XX_SCR_PAD0			(REGISTERS_BASE + 0x5608)
+#define WL12XX_SCR_PAD1			(REGISTERS_BASE + 0x560C)
+#define WL12XX_SCR_PAD2			(REGISTERS_BASE + 0x5610)
+#define WL12XX_SCR_PAD3			(REGISTERS_BASE + 0x5614)
+#define WL12XX_SCR_PAD4			(REGISTERS_BASE + 0x5618)
+#define WL12XX_SCR_PAD4_SET		(REGISTERS_BASE + 0x561C)
+#define WL12XX_SCR_PAD4_CLR		(REGISTERS_BASE + 0x5620)
+#define WL12XX_SCR_PAD5			(REGISTERS_BASE + 0x5624)
+#define WL12XX_SCR_PAD5_SET		(REGISTERS_BASE + 0x5628)
+#define WL12XX_SCR_PAD5_CLR		(REGISTERS_BASE + 0x562C)
+#define WL12XX_SCR_PAD6			(REGISTERS_BASE + 0x5630)
+#define WL12XX_SCR_PAD7			(REGISTERS_BASE + 0x5634)
+#define WL12XX_SCR_PAD8			(REGISTERS_BASE + 0x5638)
+#define WL12XX_SCR_PAD9			(REGISTERS_BASE + 0x563C)
+
+/* Spare registers*/
+#define WL12XX_SPARE_A1			(REGISTERS_BASE + 0x0994)
+#define WL12XX_SPARE_A2			(REGISTERS_BASE + 0x0998)
+#define WL12XX_SPARE_A3			(REGISTERS_BASE + 0x099C)
+#define WL12XX_SPARE_A4			(REGISTERS_BASE + 0x09A0)
+#define WL12XX_SPARE_A5			(REGISTERS_BASE + 0x09A4)
+#define WL12XX_SPARE_A6			(REGISTERS_BASE + 0x09A8)
+#define WL12XX_SPARE_A7			(REGISTERS_BASE + 0x09AC)
+#define WL12XX_SPARE_A8			(REGISTERS_BASE + 0x09B0)
+#define WL12XX_SPARE_B1			(REGISTERS_BASE + 0x5420)
+#define WL12XX_SPARE_B2			(REGISTERS_BASE + 0x5424)
+#define WL12XX_SPARE_B3			(REGISTERS_BASE + 0x5428)
+#define WL12XX_SPARE_B4			(REGISTERS_BASE + 0x542C)
+#define WL12XX_SPARE_B5			(REGISTERS_BASE + 0x5430)
+#define WL12XX_SPARE_B6			(REGISTERS_BASE + 0x5434)
+#define WL12XX_SPARE_B7			(REGISTERS_BASE + 0x5438)
+#define WL12XX_SPARE_B8			(REGISTERS_BASE + 0x543C)
+
+#define WL12XX_PLL_PARAMETERS		(REGISTERS_BASE + 0x6040)
+#define WL12XX_WU_COUNTER_PAUSE		(REGISTERS_BASE + 0x6008)
+#define WL12XX_WELP_ARM_COMMAND		(REGISTERS_BASE + 0x6100)
+#define WL12XX_DRPW_SCRATCH_START	(DRPW_BASE + 0x002C)
+
+#define WL12XX_CMD_MBOX_ADDRESS		0x407B4
+
+#define ACX_REG_EEPROM_START_BIT BIT(1)
+
+/* Command/Information Mailbox Pointers */
+
+/*===============================================
+  Command Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the command mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to
+ find the location of the command mailbox.
+ The Wlan hardware initializes the command mailbox
+ pointer with the default address of the command mailbox.
+ The command mailbox pointer is not valid until after
+ the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define WL12XX_REG_COMMAND_MAILBOX_PTR		(WL12XX_SCR_PAD0)
+
+/*===============================================
+  Information Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the information mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to find
+ the location of the information mailbox.
+ The Wlan hardware initializes the information mailbox pointer
+ with the default address of the information mailbox.
+ The information mailbox pointer is not valid
+ until after the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define WL12XX_REG_EVENT_MAILBOX_PTR		(WL12XX_SCR_PAD1)
+
+/*===============================================
+ EEPROM Read/Write Request 32bit RW
+ ------------------------------------------
+ 1 EE_READ - EEPROM Read Request 1 - Setting this bit
+ loads a single byte of data into the EE_DATA
+ register from the EEPROM location specified in
+ the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+ EE_DATA is valid when this bit is cleared.
+
+ 0 EE_WRITE  - EEPROM Write Request  - Setting this bit
+ writes a single byte of data from the EE_DATA register into the
+ EEPROM location specified in the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+*===============================================*/
+#define ACX_EE_CTL_REG                      EE_CTL
+#define EE_WRITE                            0x00000001ul
+#define EE_READ                             0x00000002ul
+
+/*===============================================
+  EEPROM Address  - 32bit RW
+  ------------------------------------------
+  This register specifies the address
+  within the EEPROM from/to which to read/write data.
+  ===============================================*/
+#define ACX_EE_ADDR_REG                     EE_ADDR
+
+/*===============================================
+  EEPROM Data  - 32bit RW
+  ------------------------------------------
+  This register either holds the read 8 bits of
+  data from the EEPROM or the write data
+  to be written to the EEPROM.
+  ===============================================*/
+#define ACX_EE_DATA_REG                     EE_DATA
+
+/*===============================================
+  EEPROM Base Address  - 32bit RW
+  ------------------------------------------
+  This register holds the upper nine bits
+  [23:15] of the 24-bit Wlan hardware memory
+  address for burst reads from EEPROM accesses.
+  The EEPROM provides the lower 15 bits of this address.
+  The MSB of the address from the EEPROM is ignored.
+  ===============================================*/
+#define ACX_EE_CFG                          EE_CFG
+
+/*===============================================
+  GPIO Output Values  -32bit, RW
+  ------------------------------------------
+  [31:16]  Reserved
+  [15: 0]  Specify the output values (at the output driver inputs) for
+  GPIO[15:0], respectively.
+  ===============================================*/
+#define ACX_GPIO_OUT_REG            GPIO_OUT
+#define ACX_MAX_GPIO_LINES          15
+
+/*===============================================
+  Contention window  -32bit, RW
+  ------------------------------------------
+  [31:26]  Reserved
+  [25:16]  Max (0x3ff)
+  [15:07]  Reserved
+  [06:00]  Current contention window value - default is 0x1F
+  ===============================================*/
+#define ACX_CONT_WIND_CFG_REG    CONT_WIND_CFG
+#define ACX_CONT_WIND_MIN_MASK   0x0000007f
+#define ACX_CONT_WIND_MAX        0x03ff0000
+
+#define REF_FREQ_19_2                       0
+#define REF_FREQ_26_0                       1
+#define REF_FREQ_38_4                       2
+#define REF_FREQ_40_0                       3
+#define REF_FREQ_33_6                       4
+#define REF_FREQ_NUM                        5
+
+#define LUT_PARAM_INTEGER_DIVIDER           0
+#define LUT_PARAM_FRACTIONAL_DIVIDER        1
+#define LUT_PARAM_ATTN_BB                   2
+#define LUT_PARAM_ALPHA_BB                  3
+#define LUT_PARAM_STOP_TIME_BB              4
+#define LUT_PARAM_BB_PLL_LOOP_FILTER        5
+#define LUT_PARAM_NUM                       6
+
+#define WL12XX_EEPROMLESS_IND		(WL12XX_SCR_PAD4)
+#define USE_EEPROM                          0
+#define NVS_DATA_BUNDARY_ALIGNMENT          4
+
+/* Firmware image header size */
+#define FW_HDR_SIZE 8
+
+/******************************************************************************
+
+    CHANNELS, BAND & REG DOMAINS definitions
+
+******************************************************************************/
+
+#define SHORT_PREAMBLE_BIT   BIT(0) /* CCK or Barker depending on the rate */
+#define OFDM_RATE_BIT        BIT(6)
+#define PBCC_RATE_BIT        BIT(7)
+
+enum {
+	CCK_LONG = 0,
+	CCK_SHORT = SHORT_PREAMBLE_BIT,
+	PBCC_LONG = PBCC_RATE_BIT,
+	PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
+	OFDM = OFDM_RATE_BIT
+};
+
+/******************************************************************************
+
+Transmit-Descriptor RATE-SET field definitions...
+
+Define a new "Rate-Set" for TX path that incorporates the
+Rate & Modulation info into a single 16-bit field.
+
+TxdRateSet_t:
+b15   - Indicates Preamble type (1=SHORT, 0=LONG).
+	Notes:
+	Must be LONG (0) for 1Mbps rate.
+	Does not apply (set to 0) for RevG-OFDM rates.
+b14   - Indicates PBCC encoding (1=PBCC, 0=not).
+	Notes:
+	Does not apply (set to 0) for rates 1 and 2 Mbps.
+	Does not apply (set to 0) for RevG-OFDM rates.
+b13    - Unused (set to 0).
+b12-b0 - Supported Rate indicator bits as defined below.
+
+******************************************************************************/
+
+#define OCP_CMD_LOOP		32
+#define OCP_CMD_WRITE		0x1
+#define OCP_CMD_READ		0x2
+#define OCP_READY_MASK		BIT(18)
+#define OCP_STATUS_MASK		(BIT(16) | BIT(17))
+#define OCP_STATUS_NO_RESP	0x00000
+#define OCP_STATUS_OK		0x10000
+#define OCP_STATUS_REQ_FAILED	0x20000
+#define OCP_STATUS_RESP_ERROR	0x30000
+
+#define OCP_REG_POLARITY     0x0064
+#define OCP_REG_CLK_TYPE     0x0448
+#define OCP_REG_CLK_POLARITY 0x0cb2
+#define OCP_REG_CLK_PULL     0x0cb4
+
+#define POLARITY_LOW         BIT(1)
+#define NO_PULL              (BIT(14) | BIT(15))
+
+#define FREF_CLK_TYPE_BITS     0xfffffe7f
+#define CLK_REQ_PRCM           0x100
+#define FREF_CLK_POLARITY_BITS 0xfffff8ff
+#define CLK_REQ_OUTN_SEL       0x700
+
+#define WU_COUNTER_PAUSE_VAL 0x3FF
+
+/* PLL configuration algorithm for wl128x */
+#define SYS_CLK_CFG_REG              0x2200
+/* Bit[0]   -  0-TCXO,  1-FREF */
+#define MCS_PLL_CLK_SEL_FREF         BIT(0)
+/* Bit[3:2] - 01-TCXO, 10-FREF */
+#define WL_CLK_REQ_TYPE_FREF         BIT(3)
+#define WL_CLK_REQ_TYPE_PG2          (BIT(3) | BIT(2))
+/* Bit[4]   -  0-TCXO,  1-FREF */
+#define PRCM_CM_EN_MUX_WLAN_FREF     BIT(4)
+
+#define TCXO_ILOAD_INT_REG           0x2264
+#define TCXO_CLK_DETECT_REG          0x2266
+
+#define TCXO_DET_FAILED              BIT(4)
+
+#define FREF_ILOAD_INT_REG           0x2084
+#define FREF_CLK_DETECT_REG          0x2086
+#define FREF_CLK_DETECT_FAIL         BIT(4)
+
+/* Use this reg for masking during driver access */
+#define WL_SPARE_REG                 0x2320
+#define WL_SPARE_VAL                 BIT(2)
+/* Bit[6:5:3] -  mask wl write SYS_CLK_CFG[8:5:2:4] */
+#define WL_SPARE_MASK_8526           (BIT(6) | BIT(5) | BIT(3))
+
+#define PLL_LOCK_COUNTERS_REG        0xD8C
+#define PLL_LOCK_COUNTERS_COEX       0x0F
+#define PLL_LOCK_COUNTERS_MCS        0xF0
+#define MCS_PLL_OVERRIDE_REG         0xD90
+#define MCS_PLL_CONFIG_REG           0xD92
+#define MCS_SEL_IN_FREQ_MASK         0x0070
+#define MCS_SEL_IN_FREQ_SHIFT        4
+#define MCS_PLL_CONFIG_REG_VAL       0x73
+#define MCS_PLL_ENABLE_HP            (BIT(0) | BIT(1))
+
+#define MCS_PLL_M_REG                0xD94
+#define MCS_PLL_N_REG                0xD96
+#define MCS_PLL_M_REG_VAL            0xC8
+#define MCS_PLL_N_REG_VAL            0x07
+
+#define SDIO_IO_DS                   0xd14
+
+/* SDIO/wSPI DS configuration values */
+enum {
+	HCI_IO_DS_8MA = 0,
+	HCI_IO_DS_4MA = 1, /* default */
+	HCI_IO_DS_6MA = 2,
+	HCI_IO_DS_2MA = 3,
+};
+
+/* end PLL configuration algorithm for wl128x */
+
+/*
+ * Host Command Interrupt. Setting this bit masks
+ * the interrupt that the host issues to inform
+ * the FW that it has sent a command
+ * to the Wlan hardware Command Mailbox.
+ */
+#define WL12XX_INTR_TRIG_CMD		BIT(0)
+
+/*
+ * Host Event Acknowlegde Interrupt. The host
+ * sets this bit to acknowledge that it received
+ * the unsolicited information from the event
+ * mailbox.
+ */
+#define WL12XX_INTR_TRIG_EVENT_ACK	BIT(1)
+
+/*===============================================
+  HI_CFG Interface Configuration Register Values
+  ------------------------------------------
+  ===============================================*/
+#define HI_CFG_UART_ENABLE          0x00000004
+#define HI_CFG_RST232_ENABLE        0x00000008
+#define HI_CFG_CLOCK_REQ_SELECT     0x00000010
+#define HI_CFG_HOST_INT_ENABLE      0x00000020
+#define HI_CFG_VLYNQ_OUTPUT_ENABLE  0x00000040
+#define HI_CFG_HOST_INT_ACTIVE_LOW  0x00000080
+#define HI_CFG_UART_TX_OUT_GPIO_15  0x00000100
+#define HI_CFG_UART_TX_OUT_GPIO_14  0x00000200
+#define HI_CFG_UART_TX_OUT_GPIO_7   0x00000400
+
+#define HI_CFG_DEF_VAL              \
+	(HI_CFG_UART_ENABLE |        \
+	HI_CFG_RST232_ENABLE |      \
+	HI_CFG_CLOCK_REQ_SELECT |   \
+	HI_CFG_HOST_INT_ENABLE)
+
+#define WL127X_REG_FUSE_DATA_2_1	0x050a
+#define WL128X_REG_FUSE_DATA_2_1	0x2152
+#define PG_VER_MASK			0x3c
+#define PG_VER_OFFSET			2
+
+#define WL127X_PG_MAJOR_VER_MASK	0x3
+#define WL127X_PG_MAJOR_VER_OFFSET	0x0
+#define WL127X_PG_MINOR_VER_MASK	0xc
+#define WL127X_PG_MINOR_VER_OFFSET	0x2
+
+#define WL128X_PG_MAJOR_VER_MASK	0xc
+#define WL128X_PG_MAJOR_VER_OFFSET	0x2
+#define WL128X_PG_MINOR_VER_MASK	0x3
+#define WL128X_PG_MINOR_VER_OFFSET	0x0
+
+#define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \
+				     WL127X_PG_MAJOR_VER_OFFSET)
+#define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \
+				     WL127X_PG_MINOR_VER_OFFSET)
+#define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \
+				     WL128X_PG_MAJOR_VER_OFFSET)
+#define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \
+				     WL128X_PG_MINOR_VER_OFFSET)
+
+#define WL12XX_REG_FUSE_BD_ADDR_1	0x00310eb4
+#define WL12XX_REG_FUSE_BD_ADDR_2	0x00310eb8
+
+#endif