diff options
Diffstat (limited to 'drivers/net/ethernet/wangxun/txgbe')
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/Makefile | 11 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c | 19 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.h | 9 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c | 304 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h | 11 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_main.c | 750 | ||||
| -rw-r--r-- | drivers/net/ethernet/wangxun/txgbe/txgbe_type.h | 103 |
7 files changed, 1207 insertions, 0 deletions
diff --git a/drivers/net/ethernet/wangxun/txgbe/Makefile b/drivers/net/ethernet/wangxun/txgbe/Makefile new file mode 100644 index 000000000..6db14a2cb --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/Makefile @@ -0,0 +1,11 @@ +# SPDX-License-Identifier: GPL-2.0 +# Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. +# +# Makefile for the Wangxun(R) 10GbE PCI Express ethernet driver +# + +obj-$(CONFIG_TXGBE) += txgbe.o + +txgbe-objs := txgbe_main.o \ + txgbe_hw.o \ + txgbe_ethtool.o diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c new file mode 100644 index 000000000..d914e9a05 --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.c @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */ + +#include <linux/pci.h> +#include <linux/phylink.h> +#include <linux/netdevice.h> + +#include "../libwx/wx_ethtool.h" +#include "txgbe_ethtool.h" + +static const struct ethtool_ops txgbe_ethtool_ops = { + .get_drvinfo = wx_get_drvinfo, + .get_link = ethtool_op_get_link, +}; + +void txgbe_set_ethtool_ops(struct net_device *netdev) +{ + netdev->ethtool_ops = &txgbe_ethtool_ops; +} diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.h new file mode 100644 index 000000000..ace1b3571 --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_ethtool.h @@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Copyright (c) 2015 - 2023 Beijing WangXun Technology Co., Ltd. */ + +#ifndef _TXGBE_ETHTOOL_H_ +#define _TXGBE_ETHTOOL_H_ + +void txgbe_set_ethtool_ops(struct net_device *netdev); + +#endif /* _TXGBE_ETHTOOL_H_ */ diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c new file mode 100644 index 000000000..ebc46f3be --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c @@ -0,0 +1,304 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */ + +#include <linux/etherdevice.h> +#include <linux/if_ether.h> +#include <linux/string.h> +#include <linux/iopoll.h> +#include <linux/types.h> +#include <linux/pci.h> + +#include "../libwx/wx_type.h" +#include "../libwx/wx_hw.h" +#include "txgbe_type.h" +#include "txgbe_hw.h" + +/** + * txgbe_init_thermal_sensor_thresh - Inits thermal sensor thresholds + * @wx: pointer to hardware structure + * + * Inits the thermal sensor thresholds according to the NVM map + * and save off the threshold and location values into mac.thermal_sensor_data + **/ +static void txgbe_init_thermal_sensor_thresh(struct wx *wx) +{ + struct wx_thermal_sensor_data *data = &wx->mac.sensor; + + memset(data, 0, sizeof(struct wx_thermal_sensor_data)); + + /* Only support thermal sensors attached to SP physical port 0 */ + if (wx->bus.func) + return; + + wr32(wx, TXGBE_TS_CTL, TXGBE_TS_CTL_EVAL_MD); + + wr32(wx, WX_TS_INT_EN, + WX_TS_INT_EN_ALARM_INT_EN | WX_TS_INT_EN_DALARM_INT_EN); + wr32(wx, WX_TS_EN, WX_TS_EN_ENA); + + data->alarm_thresh = 100; + wr32(wx, WX_TS_ALARM_THRE, 677); + data->dalarm_thresh = 90; + wr32(wx, WX_TS_DALARM_THRE, 614); +} + +/** + * txgbe_read_pba_string - Reads part number string from EEPROM + * @wx: pointer to hardware structure + * @pba_num: stores the part number string from the EEPROM + * @pba_num_size: part number string buffer length + * + * Reads the part number string from the EEPROM. + **/ +int txgbe_read_pba_string(struct wx *wx, u8 *pba_num, u32 pba_num_size) +{ + u16 pba_ptr, offset, length, data; + int ret_val; + + if (!pba_num) { + wx_err(wx, "PBA string buffer was null\n"); + return -EINVAL; + } + + ret_val = wx_read_ee_hostif(wx, + wx->eeprom.sw_region_offset + TXGBE_PBANUM0_PTR, + &data); + if (ret_val != 0) { + wx_err(wx, "NVM Read Error\n"); + return ret_val; + } + + ret_val = wx_read_ee_hostif(wx, + wx->eeprom.sw_region_offset + TXGBE_PBANUM1_PTR, + &pba_ptr); + if (ret_val != 0) { + wx_err(wx, "NVM Read Error\n"); + return ret_val; + } + + /* if data is not ptr guard the PBA must be in legacy format which + * means pba_ptr is actually our second data word for the PBA number + * and we can decode it into an ascii string + */ + if (data != TXGBE_PBANUM_PTR_GUARD) { + wx_err(wx, "NVM PBA number is not stored as string\n"); + + /* we will need 11 characters to store the PBA */ + if (pba_num_size < 11) { + wx_err(wx, "PBA string buffer too small\n"); + return -ENOMEM; + } + + /* extract hex string from data and pba_ptr */ + pba_num[0] = (data >> 12) & 0xF; + pba_num[1] = (data >> 8) & 0xF; + pba_num[2] = (data >> 4) & 0xF; + pba_num[3] = data & 0xF; + pba_num[4] = (pba_ptr >> 12) & 0xF; + pba_num[5] = (pba_ptr >> 8) & 0xF; + pba_num[6] = '-'; + pba_num[7] = 0; + pba_num[8] = (pba_ptr >> 4) & 0xF; + pba_num[9] = pba_ptr & 0xF; + + /* put a null character on the end of our string */ + pba_num[10] = '\0'; + + /* switch all the data but the '-' to hex char */ + for (offset = 0; offset < 10; offset++) { + if (pba_num[offset] < 0xA) + pba_num[offset] += '0'; + else if (pba_num[offset] < 0x10) + pba_num[offset] += 'A' - 0xA; + } + + return 0; + } + + ret_val = wx_read_ee_hostif(wx, pba_ptr, &length); + if (ret_val != 0) { + wx_err(wx, "NVM Read Error\n"); + return ret_val; + } + + if (length == 0xFFFF || length == 0) { + wx_err(wx, "NVM PBA number section invalid length\n"); + return -EINVAL; + } + + /* check if pba_num buffer is big enough */ + if (pba_num_size < (((u32)length * 2) - 1)) { + wx_err(wx, "PBA string buffer too small\n"); + return -ENOMEM; + } + + /* trim pba length from start of string */ + pba_ptr++; + length--; + + for (offset = 0; offset < length; offset++) { + ret_val = wx_read_ee_hostif(wx, pba_ptr + offset, &data); + if (ret_val != 0) { + wx_err(wx, "NVM Read Error\n"); + return ret_val; + } + pba_num[offset * 2] = (u8)(data >> 8); + pba_num[(offset * 2) + 1] = (u8)(data & 0xFF); + } + pba_num[offset * 2] = '\0'; + + return 0; +} + +/** + * txgbe_calc_eeprom_checksum - Calculates and returns the checksum + * @wx: pointer to hardware structure + * @checksum: pointer to cheksum + * + * Returns a negative error code on error + **/ +static int txgbe_calc_eeprom_checksum(struct wx *wx, u16 *checksum) +{ + u16 *eeprom_ptrs = NULL; + u32 buffer_size = 0; + u16 *buffer = NULL; + u16 *local_buffer; + int status; + u16 i; + + wx_init_eeprom_params(wx); + + if (!buffer) { + eeprom_ptrs = kvmalloc_array(TXGBE_EEPROM_LAST_WORD, sizeof(u16), + GFP_KERNEL); + if (!eeprom_ptrs) + return -ENOMEM; + /* Read pointer area */ + status = wx_read_ee_hostif_buffer(wx, 0, + TXGBE_EEPROM_LAST_WORD, + eeprom_ptrs); + if (status != 0) { + wx_err(wx, "Failed to read EEPROM image\n"); + kvfree(eeprom_ptrs); + return status; + } + local_buffer = eeprom_ptrs; + } else { + if (buffer_size < TXGBE_EEPROM_LAST_WORD) + return -EFAULT; + local_buffer = buffer; + } + + for (i = 0; i < TXGBE_EEPROM_LAST_WORD; i++) + if (i != wx->eeprom.sw_region_offset + TXGBE_EEPROM_CHECKSUM) + *checksum += local_buffer[i]; + + if (eeprom_ptrs) + kvfree(eeprom_ptrs); + + if (*checksum > TXGBE_EEPROM_SUM) + return -EINVAL; + + *checksum = TXGBE_EEPROM_SUM - *checksum; + + return 0; +} + +/** + * txgbe_validate_eeprom_checksum - Validate EEPROM checksum + * @wx: pointer to hardware structure + * @checksum_val: calculated checksum + * + * Performs checksum calculation and validates the EEPROM checksum. If the + * caller does not need checksum_val, the value can be NULL. + **/ +int txgbe_validate_eeprom_checksum(struct wx *wx, u16 *checksum_val) +{ + u16 read_checksum = 0; + u16 checksum; + int status; + + /* Read the first word from the EEPROM. If this times out or fails, do + * not continue or we could be in for a very long wait while every + * EEPROM read fails + */ + status = wx_read_ee_hostif(wx, 0, &checksum); + if (status) { + wx_err(wx, "EEPROM read failed\n"); + return status; + } + + checksum = 0; + status = txgbe_calc_eeprom_checksum(wx, &checksum); + if (status != 0) + return status; + + status = wx_read_ee_hostif(wx, wx->eeprom.sw_region_offset + + TXGBE_EEPROM_CHECKSUM, &read_checksum); + if (status != 0) + return status; + + /* Verify read checksum from EEPROM is the same as + * calculated checksum + */ + if (read_checksum != checksum) { + status = -EIO; + wx_err(wx, "Invalid EEPROM checksum\n"); + } + + /* If the user cares, return the calculated checksum */ + if (checksum_val) + *checksum_val = checksum; + + return status; +} + +static void txgbe_reset_misc(struct wx *wx) +{ + wx_reset_misc(wx); + txgbe_init_thermal_sensor_thresh(wx); +} + +/** + * txgbe_reset_hw - Perform hardware reset + * @wx: pointer to wx structure + * + * Resets the hardware by resetting the transmit and receive units, masks + * and clears all interrupts, perform a PHY reset, and perform a link (MAC) + * reset. + **/ +int txgbe_reset_hw(struct wx *wx) +{ + int status; + + /* Call adapter stop to disable tx/rx and clear interrupts */ + status = wx_stop_adapter(wx); + if (status != 0) + return status; + + if (!(((wx->subsystem_device_id & WX_NCSI_MASK) == WX_NCSI_SUP) || + ((wx->subsystem_device_id & WX_WOL_MASK) == WX_WOL_SUP))) + wx_reset_hostif(wx); + + usleep_range(10, 100); + + status = wx_check_flash_load(wx, TXGBE_SPI_ILDR_STATUS_LAN_SW_RST(wx->bus.func)); + if (status != 0) + return status; + + txgbe_reset_misc(wx); + + /* Store the permanent mac address */ + wx_get_mac_addr(wx, wx->mac.perm_addr); + + /* Store MAC address from RAR0, clear receive address registers, and + * clear the multicast table. Also reset num_rar_entries to 128, + * since we modify this value when programming the SAN MAC address. + */ + wx->mac.num_rar_entries = TXGBE_SP_RAR_ENTRIES; + wx_init_rx_addrs(wx); + + pci_set_master(wx->pdev); + + return 0; +} diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h new file mode 100644 index 000000000..e82f65dff --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h @@ -0,0 +1,11 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */ + +#ifndef _TXGBE_HW_H_ +#define _TXGBE_HW_H_ + +int txgbe_read_pba_string(struct wx *wx, u8 *pba_num, u32 pba_num_size); +int txgbe_validate_eeprom_checksum(struct wx *wx, u16 *checksum_val); +int txgbe_reset_hw(struct wx *wx); + +#endif /* _TXGBE_HW_H_ */ diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c new file mode 100644 index 000000000..6c0a98230 --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_main.c @@ -0,0 +1,750 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */ + +#include <linux/types.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/netdevice.h> +#include <linux/string.h> +#include <linux/aer.h> +#include <linux/etherdevice.h> +#include <net/ip.h> + +#include "../libwx/wx_type.h" +#include "../libwx/wx_lib.h" +#include "../libwx/wx_hw.h" +#include "txgbe_type.h" +#include "txgbe_hw.h" +#include "txgbe_ethtool.h" + +char txgbe_driver_name[] = "txgbe"; + +/* txgbe_pci_tbl - PCI Device ID Table + * + * Wildcard entries (PCI_ANY_ID) should come last + * Last entry must be all 0s + * + * { Vendor ID, Device ID, SubVendor ID, SubDevice ID, + * Class, Class Mask, private data (not used) } + */ +static const struct pci_device_id txgbe_pci_tbl[] = { + { PCI_VDEVICE(WANGXUN, TXGBE_DEV_ID_SP1000), 0}, + { PCI_VDEVICE(WANGXUN, TXGBE_DEV_ID_WX1820), 0}, + /* required last entry */ + { .device = 0 } +}; + +#define DEFAULT_DEBUG_LEVEL_SHIFT 3 + +static void txgbe_check_minimum_link(struct wx *wx) +{ + struct pci_dev *pdev; + + pdev = wx->pdev; + pcie_print_link_status(pdev); +} + +/** + * txgbe_enumerate_functions - Get the number of ports this device has + * @wx: wx structure + * + * This function enumerates the phsyical functions co-located on a single slot, + * in order to determine how many ports a device has. This is most useful in + * determining the required GT/s of PCIe bandwidth necessary for optimal + * performance. + **/ +static int txgbe_enumerate_functions(struct wx *wx) +{ + struct pci_dev *entry, *pdev = wx->pdev; + int physfns = 0; + + list_for_each_entry(entry, &pdev->bus->devices, bus_list) { + /* When the devices on the bus don't all match our device ID, + * we can't reliably determine the correct number of + * functions. This can occur if a function has been direct + * attached to a virtual machine using VT-d. + */ + if (entry->vendor != pdev->vendor || + entry->device != pdev->device) + return -EINVAL; + + physfns++; + } + + return physfns; +} + +/** + * txgbe_irq_enable - Enable default interrupt generation settings + * @wx: pointer to private structure + * @queues: enable irqs for queues + **/ +static void txgbe_irq_enable(struct wx *wx, bool queues) +{ + /* unmask interrupt */ + wx_intr_enable(wx, TXGBE_INTR_MISC(wx)); + if (queues) + wx_intr_enable(wx, TXGBE_INTR_QALL(wx)); +} + +/** + * txgbe_intr - msi/legacy mode Interrupt Handler + * @irq: interrupt number + * @data: pointer to a network interface device structure + **/ +static irqreturn_t txgbe_intr(int __always_unused irq, void *data) +{ + struct wx_q_vector *q_vector; + struct wx *wx = data; + struct pci_dev *pdev; + u32 eicr; + + q_vector = wx->q_vector[0]; + pdev = wx->pdev; + + eicr = wx_misc_isb(wx, WX_ISB_VEC0); + if (!eicr) { + /* shared interrupt alert! + * the interrupt that we masked before the ICR read. + */ + if (netif_running(wx->netdev)) + txgbe_irq_enable(wx, true); + return IRQ_NONE; /* Not our interrupt */ + } + wx->isb_mem[WX_ISB_VEC0] = 0; + if (!(pdev->msi_enabled)) + wr32(wx, WX_PX_INTA, 1); + + wx->isb_mem[WX_ISB_MISC] = 0; + /* would disable interrupts here but it is auto disabled */ + napi_schedule_irqoff(&q_vector->napi); + + /* re-enable link(maybe) and non-queue interrupts, no flush. + * txgbe_poll will re-enable the queue interrupts + */ + if (netif_running(wx->netdev)) + txgbe_irq_enable(wx, false); + + return IRQ_HANDLED; +} + +static irqreturn_t txgbe_msix_other(int __always_unused irq, void *data) +{ + struct wx *wx = data; + + /* re-enable the original interrupt state */ + if (netif_running(wx->netdev)) + txgbe_irq_enable(wx, false); + + return IRQ_HANDLED; +} + +/** + * txgbe_request_msix_irqs - Initialize MSI-X interrupts + * @wx: board private structure + * + * Allocate MSI-X vectors and request interrupts from the kernel. + **/ +static int txgbe_request_msix_irqs(struct wx *wx) +{ + struct net_device *netdev = wx->netdev; + int vector, err; + + for (vector = 0; vector < wx->num_q_vectors; vector++) { + struct wx_q_vector *q_vector = wx->q_vector[vector]; + struct msix_entry *entry = &wx->msix_entries[vector]; + + if (q_vector->tx.ring && q_vector->rx.ring) + snprintf(q_vector->name, sizeof(q_vector->name) - 1, + "%s-TxRx-%d", netdev->name, entry->entry); + else + /* skip this unused q_vector */ + continue; + + err = request_irq(entry->vector, wx_msix_clean_rings, 0, + q_vector->name, q_vector); + if (err) { + wx_err(wx, "request_irq failed for MSIX interrupt %s Error: %d\n", + q_vector->name, err); + goto free_queue_irqs; + } + } + + err = request_irq(wx->msix_entries[vector].vector, + txgbe_msix_other, 0, netdev->name, wx); + if (err) { + wx_err(wx, "request_irq for msix_other failed: %d\n", err); + goto free_queue_irqs; + } + + return 0; + +free_queue_irqs: + while (vector) { + vector--; + free_irq(wx->msix_entries[vector].vector, + wx->q_vector[vector]); + } + wx_reset_interrupt_capability(wx); + return err; +} + +/** + * txgbe_request_irq - initialize interrupts + * @wx: board private structure + * + * Attempt to configure interrupts using the best available + * capabilities of the hardware and kernel. + **/ +static int txgbe_request_irq(struct wx *wx) +{ + struct net_device *netdev = wx->netdev; + struct pci_dev *pdev = wx->pdev; + int err; + + if (pdev->msix_enabled) + err = txgbe_request_msix_irqs(wx); + else if (pdev->msi_enabled) + err = request_irq(wx->pdev->irq, &txgbe_intr, 0, + netdev->name, wx); + else + err = request_irq(wx->pdev->irq, &txgbe_intr, IRQF_SHARED, + netdev->name, wx); + + if (err) + wx_err(wx, "request_irq failed, Error %d\n", err); + + return err; +} + +static void txgbe_up_complete(struct wx *wx) +{ + u32 reg; + + wx_control_hw(wx, true); + wx_configure_vectors(wx); + + /* make sure to complete pre-operations */ + smp_mb__before_atomic(); + wx_napi_enable_all(wx); + + /* clear any pending interrupts, may auto mask */ + rd32(wx, WX_PX_IC); + rd32(wx, WX_PX_MISC_IC); + txgbe_irq_enable(wx, true); + + /* Configure MAC Rx and Tx when link is up */ + reg = rd32(wx, WX_MAC_RX_CFG); + wr32(wx, WX_MAC_RX_CFG, reg); + wr32(wx, WX_MAC_PKT_FLT, WX_MAC_PKT_FLT_PR); + reg = rd32(wx, WX_MAC_WDG_TIMEOUT); + wr32(wx, WX_MAC_WDG_TIMEOUT, reg); + reg = rd32(wx, WX_MAC_TX_CFG); + wr32(wx, WX_MAC_TX_CFG, (reg & ~WX_MAC_TX_CFG_SPEED_MASK) | WX_MAC_TX_CFG_SPEED_10G); + + /* enable transmits */ + netif_tx_start_all_queues(wx->netdev); + netif_carrier_on(wx->netdev); +} + +static void txgbe_reset(struct wx *wx) +{ + struct net_device *netdev = wx->netdev; + u8 old_addr[ETH_ALEN]; + int err; + + err = txgbe_reset_hw(wx); + if (err != 0) + wx_err(wx, "Hardware Error: %d\n", err); + + /* do not flush user set addresses */ + memcpy(old_addr, &wx->mac_table[0].addr, netdev->addr_len); + wx_flush_sw_mac_table(wx); + wx_mac_set_default_filter(wx, old_addr); +} + +static void txgbe_disable_device(struct wx *wx) +{ + struct net_device *netdev = wx->netdev; + u32 i; + + wx_disable_pcie_master(wx); + /* disable receives */ + wx_disable_rx(wx); + + /* disable all enabled rx queues */ + for (i = 0; i < wx->num_rx_queues; i++) + /* this call also flushes the previous write */ + wx_disable_rx_queue(wx, wx->rx_ring[i]); + + netif_tx_stop_all_queues(netdev); + netif_carrier_off(netdev); + netif_tx_disable(netdev); + + wx_irq_disable(wx); + wx_napi_disable_all(wx); + + if (wx->bus.func < 2) + wr32m(wx, TXGBE_MIS_PRB_CTL, TXGBE_MIS_PRB_CTL_LAN_UP(wx->bus.func), 0); + else + wx_err(wx, "%s: invalid bus lan id %d\n", + __func__, wx->bus.func); + + if (!(((wx->subsystem_device_id & WX_NCSI_MASK) == WX_NCSI_SUP) || + ((wx->subsystem_device_id & WX_WOL_MASK) == WX_WOL_SUP))) { + /* disable mac transmiter */ + wr32m(wx, WX_MAC_TX_CFG, WX_MAC_TX_CFG_TE, 0); + } + + /* disable transmits in the hardware now that interrupts are off */ + for (i = 0; i < wx->num_tx_queues; i++) { + u8 reg_idx = wx->tx_ring[i]->reg_idx; + + wr32(wx, WX_PX_TR_CFG(reg_idx), WX_PX_TR_CFG_SWFLSH); + } + + /* Disable the Tx DMA engine */ + wr32m(wx, WX_TDM_CTL, WX_TDM_CTL_TE, 0); +} + +static void txgbe_down(struct wx *wx) +{ + txgbe_disable_device(wx); + txgbe_reset(wx); + + wx_clean_all_tx_rings(wx); + wx_clean_all_rx_rings(wx); +} + +/** + * txgbe_sw_init - Initialize general software structures (struct wx) + * @wx: board private structure to initialize + **/ +static int txgbe_sw_init(struct wx *wx) +{ + u16 msix_count = 0; + int err; + + wx->mac.num_rar_entries = TXGBE_SP_RAR_ENTRIES; + wx->mac.max_tx_queues = TXGBE_SP_MAX_TX_QUEUES; + wx->mac.max_rx_queues = TXGBE_SP_MAX_RX_QUEUES; + wx->mac.mcft_size = TXGBE_SP_MC_TBL_SIZE; + wx->mac.rx_pb_size = TXGBE_SP_RX_PB_SIZE; + wx->mac.tx_pb_size = TXGBE_SP_TDB_PB_SZ; + + /* PCI config space info */ + err = wx_sw_init(wx); + if (err < 0) { + wx_err(wx, "read of internal subsystem device id failed\n"); + return err; + } + + switch (wx->device_id) { + case TXGBE_DEV_ID_SP1000: + case TXGBE_DEV_ID_WX1820: + wx->mac.type = wx_mac_sp; + break; + default: + wx->mac.type = wx_mac_unknown; + break; + } + + /* Set common capability flags and settings */ + wx->max_q_vectors = TXGBE_MAX_MSIX_VECTORS; + err = wx_get_pcie_msix_counts(wx, &msix_count, TXGBE_MAX_MSIX_VECTORS); + if (err) + wx_err(wx, "Do not support MSI-X\n"); + wx->mac.max_msix_vectors = msix_count; + + /* enable itr by default in dynamic mode */ + wx->rx_itr_setting = 1; + wx->tx_itr_setting = 1; + + /* set default ring sizes */ + wx->tx_ring_count = TXGBE_DEFAULT_TXD; + wx->rx_ring_count = TXGBE_DEFAULT_RXD; + + /* set default work limits */ + wx->tx_work_limit = TXGBE_DEFAULT_TX_WORK; + wx->rx_work_limit = TXGBE_DEFAULT_RX_WORK; + + return 0; +} + +/** + * txgbe_open - Called when a network interface is made active + * @netdev: network interface device structure + * + * Returns 0 on success, negative value on failure + * + * The open entry point is called when a network interface is made + * active by the system (IFF_UP). + **/ +static int txgbe_open(struct net_device *netdev) +{ + struct wx *wx = netdev_priv(netdev); + int err; + + err = wx_setup_resources(wx); + if (err) + goto err_reset; + + wx_configure(wx); + + err = txgbe_request_irq(wx); + if (err) + goto err_free_isb; + + /* Notify the stack of the actual queue counts. */ + err = netif_set_real_num_tx_queues(netdev, wx->num_tx_queues); + if (err) + goto err_free_irq; + + err = netif_set_real_num_rx_queues(netdev, wx->num_rx_queues); + if (err) + goto err_free_irq; + + txgbe_up_complete(wx); + + return 0; + +err_free_irq: + wx_free_irq(wx); +err_free_isb: + wx_free_isb_resources(wx); +err_reset: + txgbe_reset(wx); + + return err; +} + +/** + * txgbe_close_suspend - actions necessary to both suspend and close flows + * @wx: the private wx struct + * + * This function should contain the necessary work common to both suspending + * and closing of the device. + */ +static void txgbe_close_suspend(struct wx *wx) +{ + txgbe_disable_device(wx); + wx_free_resources(wx); +} + +/** + * txgbe_close - Disables a network interface + * @netdev: network interface device structure + * + * Returns 0, this is not allowed to fail + * + * The close entry point is called when an interface is de-activated + * by the OS. The hardware is still under the drivers control, but + * needs to be disabled. A global MAC reset is issued to stop the + * hardware, and all transmit and receive resources are freed. + **/ +static int txgbe_close(struct net_device *netdev) +{ + struct wx *wx = netdev_priv(netdev); + + txgbe_down(wx); + wx_free_irq(wx); + wx_free_resources(wx); + wx_control_hw(wx, false); + + return 0; +} + +static void txgbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake) +{ + struct wx *wx = pci_get_drvdata(pdev); + struct net_device *netdev; + + netdev = wx->netdev; + netif_device_detach(netdev); + + rtnl_lock(); + if (netif_running(netdev)) + txgbe_close_suspend(wx); + rtnl_unlock(); + + wx_control_hw(wx, false); + + pci_disable_device(pdev); +} + +static void txgbe_shutdown(struct pci_dev *pdev) +{ + bool wake; + + txgbe_dev_shutdown(pdev, &wake); + + if (system_state == SYSTEM_POWER_OFF) { + pci_wake_from_d3(pdev, wake); + pci_set_power_state(pdev, PCI_D3hot); + } +} + +static const struct net_device_ops txgbe_netdev_ops = { + .ndo_open = txgbe_open, + .ndo_stop = txgbe_close, + .ndo_start_xmit = wx_xmit_frame, + .ndo_set_rx_mode = wx_set_rx_mode, + .ndo_validate_addr = eth_validate_addr, + .ndo_set_mac_address = wx_set_mac, + .ndo_get_stats64 = wx_get_stats64, +}; + +/** + * txgbe_probe - Device Initialization Routine + * @pdev: PCI device information struct + * @ent: entry in txgbe_pci_tbl + * + * Returns 0 on success, negative on failure + * + * txgbe_probe initializes an adapter identified by a pci_dev structure. + * The OS initialization, configuring of the wx private structure, + * and a hardware reset occur. + **/ +static int txgbe_probe(struct pci_dev *pdev, + const struct pci_device_id __always_unused *ent) +{ + struct net_device *netdev; + int err, expected_gts; + struct wx *wx = NULL; + + u16 eeprom_verh = 0, eeprom_verl = 0, offset = 0; + u16 eeprom_cfg_blkh = 0, eeprom_cfg_blkl = 0; + u16 build = 0, major = 0, patch = 0; + u8 part_str[TXGBE_PBANUM_LENGTH]; + u32 etrack_id = 0; + + err = pci_enable_device_mem(pdev); + if (err) + return err; + + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); + if (err) { + dev_err(&pdev->dev, + "No usable DMA configuration, aborting\n"); + goto err_pci_disable_dev; + } + + err = pci_request_selected_regions(pdev, + pci_select_bars(pdev, IORESOURCE_MEM), + txgbe_driver_name); + if (err) { + dev_err(&pdev->dev, + "pci_request_selected_regions failed 0x%x\n", err); + goto err_pci_disable_dev; + } + + pci_enable_pcie_error_reporting(pdev); + pci_set_master(pdev); + + netdev = devm_alloc_etherdev_mqs(&pdev->dev, + sizeof(struct wx), + TXGBE_MAX_TX_QUEUES, + TXGBE_MAX_RX_QUEUES); + if (!netdev) { + err = -ENOMEM; + goto err_pci_release_regions; + } + + SET_NETDEV_DEV(netdev, &pdev->dev); + + wx = netdev_priv(netdev); + wx->netdev = netdev; + wx->pdev = pdev; + + wx->msg_enable = (1 << DEFAULT_DEBUG_LEVEL_SHIFT) - 1; + + wx->hw_addr = devm_ioremap(&pdev->dev, + pci_resource_start(pdev, 0), + pci_resource_len(pdev, 0)); + if (!wx->hw_addr) { + err = -EIO; + goto err_pci_release_regions; + } + + wx->driver_name = txgbe_driver_name; + txgbe_set_ethtool_ops(netdev); + netdev->netdev_ops = &txgbe_netdev_ops; + + /* setup the private structure */ + err = txgbe_sw_init(wx); + if (err) + goto err_free_mac_table; + + /* check if flash load is done after hw power up */ + err = wx_check_flash_load(wx, TXGBE_SPI_ILDR_STATUS_PERST); + if (err) + goto err_free_mac_table; + err = wx_check_flash_load(wx, TXGBE_SPI_ILDR_STATUS_PWRRST); + if (err) + goto err_free_mac_table; + + err = wx_mng_present(wx); + if (err) { + dev_err(&pdev->dev, "Management capability is not present\n"); + goto err_free_mac_table; + } + + err = txgbe_reset_hw(wx); + if (err) { + dev_err(&pdev->dev, "HW Init failed: %d\n", err); + goto err_free_mac_table; + } + + netdev->features |= NETIF_F_HIGHDMA; + netdev->features = NETIF_F_SG; + + /* copy netdev features into list of user selectable features */ + netdev->hw_features |= netdev->features | NETIF_F_RXALL; + + netdev->priv_flags |= IFF_UNICAST_FLT; + netdev->priv_flags |= IFF_SUPP_NOFCS; + + netdev->min_mtu = ETH_MIN_MTU; + netdev->max_mtu = TXGBE_MAX_JUMBO_FRAME_SIZE - (ETH_HLEN + ETH_FCS_LEN); + + /* make sure the EEPROM is good */ + err = txgbe_validate_eeprom_checksum(wx, NULL); + if (err != 0) { + dev_err(&pdev->dev, "The EEPROM Checksum Is Not Valid\n"); + wr32(wx, WX_MIS_RST, WX_MIS_RST_SW_RST); + err = -EIO; + goto err_free_mac_table; + } + + eth_hw_addr_set(netdev, wx->mac.perm_addr); + wx_mac_set_default_filter(wx, wx->mac.perm_addr); + + err = wx_init_interrupt_scheme(wx); + if (err) + goto err_free_mac_table; + + /* Save off EEPROM version number and Option Rom version which + * together make a unique identify for the eeprom + */ + wx_read_ee_hostif(wx, + wx->eeprom.sw_region_offset + TXGBE_EEPROM_VERSION_H, + &eeprom_verh); + wx_read_ee_hostif(wx, + wx->eeprom.sw_region_offset + TXGBE_EEPROM_VERSION_L, + &eeprom_verl); + etrack_id = (eeprom_verh << 16) | eeprom_verl; + + wx_read_ee_hostif(wx, + wx->eeprom.sw_region_offset + TXGBE_ISCSI_BOOT_CONFIG, + &offset); + + /* Make sure offset to SCSI block is valid */ + if (!(offset == 0x0) && !(offset == 0xffff)) { + wx_read_ee_hostif(wx, offset + 0x84, &eeprom_cfg_blkh); + wx_read_ee_hostif(wx, offset + 0x83, &eeprom_cfg_blkl); + + /* Only display Option Rom if exist */ + if (eeprom_cfg_blkl && eeprom_cfg_blkh) { + major = eeprom_cfg_blkl >> 8; + build = (eeprom_cfg_blkl << 8) | (eeprom_cfg_blkh >> 8); + patch = eeprom_cfg_blkh & 0x00ff; + + snprintf(wx->eeprom_id, sizeof(wx->eeprom_id), + "0x%08x, %d.%d.%d", etrack_id, major, build, + patch); + } else { + snprintf(wx->eeprom_id, sizeof(wx->eeprom_id), + "0x%08x", etrack_id); + } + } else { + snprintf(wx->eeprom_id, sizeof(wx->eeprom_id), + "0x%08x", etrack_id); + } + + err = register_netdev(netdev); + if (err) + goto err_release_hw; + + pci_set_drvdata(pdev, wx); + + netif_tx_stop_all_queues(netdev); + + /* calculate the expected PCIe bandwidth required for optimal + * performance. Note that some older parts will never have enough + * bandwidth due to being older generation PCIe parts. We clamp these + * parts to ensure that no warning is displayed, as this could confuse + * users otherwise. + */ + expected_gts = txgbe_enumerate_functions(wx) * 10; + + /* don't check link if we failed to enumerate functions */ + if (expected_gts > 0) + txgbe_check_minimum_link(wx); + else + dev_warn(&pdev->dev, "Failed to enumerate PF devices.\n"); + + /* First try to read PBA as a string */ + err = txgbe_read_pba_string(wx, part_str, TXGBE_PBANUM_LENGTH); + if (err) + strncpy(part_str, "Unknown", TXGBE_PBANUM_LENGTH); + + netif_info(wx, probe, netdev, "%pM\n", netdev->dev_addr); + + return 0; + +err_release_hw: + wx_clear_interrupt_scheme(wx); + wx_control_hw(wx, false); +err_free_mac_table: + kfree(wx->mac_table); +err_pci_release_regions: + pci_disable_pcie_error_reporting(pdev); + pci_release_selected_regions(pdev, + pci_select_bars(pdev, IORESOURCE_MEM)); +err_pci_disable_dev: + pci_disable_device(pdev); + return err; +} + +/** + * txgbe_remove - Device Removal Routine + * @pdev: PCI device information struct + * + * txgbe_remove is called by the PCI subsystem to alert the driver + * that it should release a PCI device. The could be caused by a + * Hot-Plug event, or because the driver is going to be removed from + * memory. + **/ +static void txgbe_remove(struct pci_dev *pdev) +{ + struct wx *wx = pci_get_drvdata(pdev); + struct net_device *netdev; + + netdev = wx->netdev; + unregister_netdev(netdev); + + pci_release_selected_regions(pdev, + pci_select_bars(pdev, IORESOURCE_MEM)); + + kfree(wx->mac_table); + wx_clear_interrupt_scheme(wx); + + pci_disable_pcie_error_reporting(pdev); + + pci_disable_device(pdev); +} + +static struct pci_driver txgbe_driver = { + .name = txgbe_driver_name, + .id_table = txgbe_pci_tbl, + .probe = txgbe_probe, + .remove = txgbe_remove, + .shutdown = txgbe_shutdown, +}; + +module_pci_driver(txgbe_driver); + +MODULE_DEVICE_TABLE(pci, txgbe_pci_tbl); +MODULE_AUTHOR("Beijing WangXun Technology Co., Ltd, <software@trustnetic.com>"); +MODULE_DESCRIPTION("WangXun(R) 10 Gigabit PCI Express Network Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h new file mode 100644 index 000000000..563ea51de --- /dev/null +++ b/drivers/net/ethernet/wangxun/txgbe/txgbe_type.h @@ -0,0 +1,103 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Copyright (c) 2015 - 2022 Beijing WangXun Technology Co., Ltd. */ + +#ifndef _TXGBE_TYPE_H_ +#define _TXGBE_TYPE_H_ + +/* Device IDs */ +#define TXGBE_DEV_ID_SP1000 0x1001 +#define TXGBE_DEV_ID_WX1820 0x2001 + +/* Subsystem IDs */ +/* SFP */ +#define TXGBE_ID_SP1000_SFP 0x0000 +#define TXGBE_ID_WX1820_SFP 0x2000 +#define TXGBE_ID_SFP 0x00 + +/* copper */ +#define TXGBE_ID_SP1000_XAUI 0x1010 +#define TXGBE_ID_WX1820_XAUI 0x2010 +#define TXGBE_ID_XAUI 0x10 +#define TXGBE_ID_SP1000_SGMII 0x1020 +#define TXGBE_ID_WX1820_SGMII 0x2020 +#define TXGBE_ID_SGMII 0x20 +/* backplane */ +#define TXGBE_ID_SP1000_KR_KX_KX4 0x1030 +#define TXGBE_ID_WX1820_KR_KX_KX4 0x2030 +#define TXGBE_ID_KR_KX_KX4 0x30 +/* MAC Interface */ +#define TXGBE_ID_SP1000_MAC_XAUI 0x1040 +#define TXGBE_ID_WX1820_MAC_XAUI 0x2040 +#define TXGBE_ID_MAC_XAUI 0x40 +#define TXGBE_ID_SP1000_MAC_SGMII 0x1060 +#define TXGBE_ID_WX1820_MAC_SGMII 0x2060 +#define TXGBE_ID_MAC_SGMII 0x60 + +/* Combined interface*/ +#define TXGBE_ID_SFI_XAUI 0x50 + +/* Revision ID */ +#define TXGBE_SP_MPW 1 + +/**************** SP Registers ****************************/ +/* chip control Registers */ +#define TXGBE_MIS_PRB_CTL 0x10010 +#define TXGBE_MIS_PRB_CTL_LAN_UP(_i) BIT(1 - (_i)) +/* FMGR Registers */ +#define TXGBE_SPI_ILDR_STATUS 0x10120 +#define TXGBE_SPI_ILDR_STATUS_PERST BIT(0) /* PCIE_PERST is done */ +#define TXGBE_SPI_ILDR_STATUS_PWRRST BIT(1) /* Power on reset is done */ +#define TXGBE_SPI_ILDR_STATUS_LAN_SW_RST(_i) BIT((_i) + 9) /* lan soft reset done */ + +/* Sensors for PVT(Process Voltage Temperature) */ +#define TXGBE_TS_CTL 0x10300 +#define TXGBE_TS_CTL_EVAL_MD BIT(31) + +/* Part Number String Length */ +#define TXGBE_PBANUM_LENGTH 32 + +/* Checksum and EEPROM pointers */ +#define TXGBE_EEPROM_LAST_WORD 0x800 +#define TXGBE_EEPROM_CHECKSUM 0x2F +#define TXGBE_EEPROM_SUM 0xBABA +#define TXGBE_EEPROM_VERSION_L 0x1D +#define TXGBE_EEPROM_VERSION_H 0x1E +#define TXGBE_ISCSI_BOOT_CONFIG 0x07 +#define TXGBE_PBANUM0_PTR 0x05 +#define TXGBE_PBANUM1_PTR 0x06 +#define TXGBE_PBANUM_PTR_GUARD 0xFAFA + +#define TXGBE_MAX_MSIX_VECTORS 64 +#define TXGBE_MAX_FDIR_INDICES 63 + +#define TXGBE_MAX_RX_QUEUES (TXGBE_MAX_FDIR_INDICES + 1) +#define TXGBE_MAX_TX_QUEUES (TXGBE_MAX_FDIR_INDICES + 1) + +#define TXGBE_SP_MAX_TX_QUEUES 128 +#define TXGBE_SP_MAX_RX_QUEUES 128 +#define TXGBE_SP_RAR_ENTRIES 128 +#define TXGBE_SP_MC_TBL_SIZE 128 +#define TXGBE_SP_RX_PB_SIZE 512 +#define TXGBE_SP_TDB_PB_SZ (160 * 1024) /* 160KB Packet Buffer */ +#define TXGBE_MAX_JUMBO_FRAME_SIZE 9432 /* max payload 9414 */ + +/* TX/RX descriptor defines */ +#define TXGBE_DEFAULT_TXD 512 +#define TXGBE_DEFAULT_TX_WORK 256 + +#if (PAGE_SIZE < 8192) +#define TXGBE_DEFAULT_RXD 512 +#define TXGBE_DEFAULT_RX_WORK 256 +#else +#define TXGBE_DEFAULT_RXD 256 +#define TXGBE_DEFAULT_RX_WORK 128 +#endif + +#define TXGBE_INTR_MISC(A) BIT((A)->num_q_vectors) +#define TXGBE_INTR_QALL(A) (TXGBE_INTR_MISC(A) - 1) + +#define TXGBE_MAX_EITR GENMASK(11, 3) + +extern char txgbe_driver_name[]; + +#endif /* _TXGBE_TYPE_H_ */ |