Merge tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextgrafted

Pull networking updates from Jakub Kicinski:
 "Core:

   - Add dedicated kmem_cache for typical/small skb->head, avoid having
     to access struct page at kfree time, and improve memory use.

   - Introduce sysctl to set default RPS configuration for new netdevs.

   - Define Netlink protocol specification format which can be used to
     describe messages used by each family and auto-generate parsers.
     Add tools for generating kernel data structures and uAPI headers.

   - Expose all net/core sysctls inside netns.

   - Remove 4s sleep in netpoll if carrier is instantly detected on
     boot.

   - Add configurable limit of MDB entries per port, and port-vlan.

   - Continue populating drop reasons throughout the stack.

   - Retire a handful of legacy Qdiscs and classifiers.

  Protocols:

   - Support IPv4 big TCP (TSO frames larger than 64kB).

   - Add IP_LOCAL_PORT_RANGE socket option, to control local port range
     on socket by socket basis.

   - Track and report in procfs number of MPTCP sockets used.

   - Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
     manager.

   - IPv6: don't check net.ipv6.route.max_size and rely on garbage
     collection to free memory (similarly to IPv4).

   - Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).

   - ICMP: add per-rate limit counters.

   - Add support for user scanning requests in ieee802154.

   - Remove static WEP support.

   - Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
     reporting.

   - WiFi 7 EHT channel puncturing support (client & AP).

  BPF:

   - Add a rbtree data structure following the "next-gen data structure"
     precedent set by recently added linked list, that is, by using
     kfunc + kptr instead of adding a new BPF map type.

   - Expose XDP hints via kfuncs with initial support for RX hash and
     timestamp metadata.

   - Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
     better support decap on GRE tunnel devices not operating in collect
     metadata.

   - Improve x86 JIT's codegen for PROBE_MEM runtime error checks.

   - Remove the need for trace_printk_lock for bpf_trace_printk and
     bpf_trace_vprintk helpers.

   - Extend libbpf's bpf_tracing.h support for tracing arguments of
     kprobes/uprobes and syscall as a special case.

   - Significantly reduce the search time for module symbols by
     livepatch and BPF.

   - Enable cpumasks to be used as kptrs, which is useful for tracing
     programs tracking which tasks end up running on which CPUs in
     different time intervals.

   - Add support for BPF trampoline on s390x and riscv64.

   - Add capability to export the XDP features supported by the NIC.

   - Add __bpf_kfunc tag for marking kernel functions as kfuncs.

   - Add cgroup.memory=nobpf kernel parameter option to disable BPF
     memory accounting for container environments.

  Netfilter:

   - Remove the CLUSTERIP target. It has been marked as obsolete for
     years, and we still have WARN splats wrt races of the out-of-band
     /proc interface installed by this target.

   - Add 'destroy' commands to nf_tables. They are identical to the
     existing 'delete' commands, but do not return an error if the
     referenced object (set, chain, rule...) did not exist.

  Driver API:

   - Improve cpumask_local_spread() locality to help NICs set the right
     IRQ affinity on AMD platforms.

   - Separate C22 and C45 MDIO bus transactions more clearly.

   - Introduce new DCB table to control DSCP rewrite on egress.

   - Support configuration of Physical Layer Collision Avoidance (PLCA)
     Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
     shared medium Ethernet.

   - Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
     preemption of low priority frames by high priority frames.

   - Add support for controlling MACSec offload using netlink SET.

   - Rework devlink instance refcounts to allow registration and
     de-registration under the instance lock. Split the code into
     multiple files, drop some of the unnecessarily granular locks and
     factor out common parts of netlink operation handling.

   - Add TX frame aggregation parameters (for USB drivers).

   - Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
     messages with notifications for debug.

   - Allow offloading of UDP NEW connections via act_ct.

   - Add support for per action HW stats in TC.

   - Support hardware miss to TC action (continue processing in SW from
     a specific point in the action chain).

   - Warn if old Wireless Extension user space interface is used with
     modern cfg80211/mac80211 drivers. Do not support Wireless
     Extensions for Wi-Fi 7 devices at all. Everyone should switch to
     using nl80211 interface instead.

   - Improve the CAN bit timing configuration. Use extack to return
     error messages directly to user space, update the SJW handling,
     including the definition of a new default value that will benefit
     CAN-FD controllers, by increasing their oscillator tolerance.

  New hardware / drivers:

   - Ethernet:
      - nVidia BlueField-3 support (control traffic driver)
      - Ethernet support for imx93 SoCs
      - Motorcomm yt8531 gigabit Ethernet PHY
      - onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
      - Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
      - Amlogic gxl MDIO mux

   - WiFi:
      - RealTek RTL8188EU (rtl8xxxu)
      - Qualcomm Wi-Fi 7 devices (ath12k)

   - CAN:
      - Renesas R-Car V4H

  Drivers:

   - Bluetooth:
      - Set Per Platform Antenna Gain (PPAG) for Intel controllers.

   - Ethernet NICs:
      - Intel (1G, igc):
         - support TSN / Qbv / packet scheduling features of i226 model
      - Intel (100G, ice):
         - use GNSS subsystem instead of TTY
         - multi-buffer XDP support
         - extend support for GPIO pins to E823 devices
      - nVidia/Mellanox:
         - update the shared buffer configuration on PFC commands
         - implement PTP adjphase function for HW offset control
         - TC support for Geneve and GRE with VF tunnel offload
         - more efficient crypto key management method
         - multi-port eswitch support
      - Netronome/Corigine:
         - add DCB IEEE support
         - support IPsec offloading for NFP3800
      - Freescale/NXP (enetc):
         - support XDP_REDIRECT for XDP non-linear buffers
         - improve reconfig, avoid link flap and waiting for idle
         - support MAC Merge layer
      - Other NICs:
         - sfc/ef100: add basic devlink support for ef100
         - ionic: rx_push mode operation (writing descriptors via MMIO)
         - bnxt: use the auxiliary bus abstraction for RDMA
         - r8169: disable ASPM and reset bus in case of tx timeout
         - cpsw: support QSGMII mode for J721e CPSW9G
         - cpts: support pulse-per-second output
         - ngbe: add an mdio bus driver
         - usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
         - r8152: handle devices with FW with NCM support
         - amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
         - virtio-net: support multi buffer XDP
         - virtio/vsock: replace virtio_vsock_pkt with sk_buff
         - tsnep: XDP support

   - Ethernet high-speed switches:
      - nVidia/Mellanox (mlxsw):
         - add support for latency TLV (in FW control messages)
      - Microchip (sparx5):
         - separate explicit and implicit traffic forwarding rules, make
           the implicit rules always active
         - add support for egress DSCP rewrite
         - IS0 VCAP support (Ingress Classification)
         - IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
           etc.)
         - ES2 VCAP support (Egress Access Control)
         - support for Per-Stream Filtering and Policing (802.1Q,
           8.6.5.1)

   - Ethernet embedded switches:
      - Marvell (mv88e6xxx):
         - add MAB (port auth) offload support
         - enable PTP receive for mv88e6390
      - NXP (ocelot):
         - support MAC Merge layer
         - support for the the vsc7512 internal copper phys
      - Microchip:
         - lan9303: convert to PHYLINK
         - lan966x: support TC flower filter statistics
         - lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
         - lan937x: support Credit Based Shaper configuration
         - ksz9477: support Energy Efficient Ethernet
      - other:
         - qca8k: convert to regmap read/write API, use bulk operations
         - rswitch: Improve TX timestamp accuracy

   - Intel WiFi (iwlwifi):
      - EHT (Wi-Fi 7) rate reporting
      - STEP equalizer support: transfer some STEP (connection to radio
        on platforms with integrated wifi) related parameters from the
        BIOS to the firmware.

   - Qualcomm 802.11ax WiFi (ath11k):
      - IPQ5018 support
      - Fine Timing Measurement (FTM) responder role support
      - channel 177 support

   - MediaTek WiFi (mt76):
      - per-PHY LED support
      - mt7996: EHT (Wi-Fi 7) support
      - Wireless Ethernet Dispatch (WED) reset support
      - switch to using page pool allocator

   - RealTek WiFi (rtw89):
      - support new version of Bluetooth co-existance

   - Mobile:
      - rmnet: support TX aggregation"

* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
  page_pool: add a comment explaining the fragment counter usage
  net: ethtool: fix __ethtool_dev_mm_supported() implementation
  ethtool: pse-pd: Fix double word in comments
  xsk: add linux/vmalloc.h to xsk.c
  sefltests: netdevsim: wait for devlink instance after netns removal
  selftest: fib_tests: Always cleanup before exit
  net/mlx5e: Align IPsec ASO result memory to be as required by hardware
  net/mlx5e: TC, Set CT miss to the specific ct action instance
  net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
  net/mlx5: Refactor tc miss handling to a single function
  net/mlx5: Kconfig: Make tc offload depend on tc skb extension
  net/sched: flower: Support hardware miss to tc action
  net/sched: flower: Move filter handle initialization earlier
  net/sched: cls_api: Support hardware miss to tc action
  net/sched: Rename user cookie and act cookie
  sfc: fix builds without CONFIG_RTC_LIB
  sfc: clean up some inconsistent indentings
  net/mlx4_en: Introduce flexible array to silence overflow warning
  net: lan966x: Fix possible deadlock inside PTP
  net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
  ...

12 files changed, 580 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/extcon/extcon-max3355.txt b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
new file mode 100644
index 000000000..f2288ea9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
@@ -0,0 +1,21 @@
+Maxim Integrated MAX3355 USB OTG chip
+-------------------------------------
+
+MAX3355 integrates a charge pump and comparators to enable a system with an
+integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
+device.
+
+Required properties:
+- compatible: should be "maxim,max3355";
+- maxim,shdn-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+		    connected to the MAX3355's SHDN# pin;
+- id-gpios: should contain a phandle and GPIO specifier for the GPIO pin
+	    connected to the MAX3355's ID_OUT pin.
+
+Example:
+
+	usb-otg {
+		compatible = "maxim,max3355";
+		maxim,shdn-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		id-gpios = <&gpio5 31 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-palmas.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt
new file mode 100644
index 000000000..f61d5af44
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt
@@ -0,0 +1,22 @@
+EXTCON FOR PALMAS/TWL CHIPS
+
+PALMAS USB COMPARATOR
+Required Properties:
+ - compatible: should contain one of:
+   * "ti,palmas-usb-vid".
+   * "ti,twl6035-usb-vid".
+   * "ti,palmas-usb" (DEPRECATED - use "ti,palmas-usb-vid").
+   * "ti,twl6035-usb" (DEPRECATED - use "ti,twl6035-usb-vid").
+
+Optional Properties:
+ - ti,wakeup : To enable the wakeup comparator in probe
+ - ti,enable-id-detection: Perform ID detection. If id-gpio is specified
+		it performs id-detection using GPIO else using OTG core.
+ - ti,enable-vbus-detection: Perform VBUS detection.
+ - id-gpio: gpio for GPIO ID detection. See gpio binding.
+ - debounce-delay-ms: debounce delay for GPIO ID pin in milliseconds.
+
+palmas-usb {
+       compatible = "ti,twl6035-usb", "ti,palmas-usb";
+       ti,wakeup;
+};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
new file mode 100644
index 000000000..d5cfa32ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PTN5150 CC (Configuration Channel) Logic device
+
+maintainers:
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  PTN5150 is a small thin low power CC logic chip supporting the USB Type-C
+  connector application with CC control logic detection and indication
+  functions.  It is interfaced to the host controller using an I2C interface.
+
+properties:
+  compatible:
+    const: nxp,ptn5150
+
+  int-gpios:
+    maxItems: 1
+    deprecated: true
+    description:
+      GPIO pin (input) connected to the PTN5150's INTB pin.
+      Use "interrupts" instead.
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  vbus-gpios:
+    maxItems: 1
+    description:
+      GPIO pin (output) used to control VBUS. If skipped, no such control
+      takes place.
+
+required:
+  - compatible
+  - interrupts
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ptn5150@1d {
+            compatible = "nxp,ptn5150";
+            reg = <0x1d>;
+            interrupt-parent = <&msmgpio>;
+            interrupts = <78 IRQ_TYPE_LEVEL_HIGH>;
+            vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt
new file mode 100644
index 000000000..cfcf455ad
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-rt8973a.txt
@@ -0,0 +1,23 @@
+
+* Richtek RT8973A - Micro USB Switch device
+
+The Richtek RT8973A is Micro USB Switch with OVP and I2C interface. The RT8973A
+is a USB port accessory detector and switch that is optimized to protect low
+voltage system from abnormal high input voltage (up to 28V) and supports high
+speed USB operation. Also, RT8973A support 'auto-configuration' mode.
+If auto-configuration mode is enabled, RT8973A would control internal h/w patch
+for USB D-/D+ switching.
+
+Required properties:
+- compatible: Should be "richtek,rt8973a-muic"
+- reg: Specifies the I2C slave address of the MUIC block. It should be 0x14
+- interrupts: Interrupt specifiers for detection interrupt sources.
+
+Example:
+
+	rt8973a@14 {
+		compatible = "richtek,rt8973a-muic";
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 0>;
+		reg = <0x14>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
new file mode 100644
index 000000000..dfc14f71e
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt
@@ -0,0 +1,21 @@
+USB GPIO Extcon device
+
+This is a virtual device used to generate USB cable states from the USB ID pin
+connected to a GPIO pin.
+
+Required properties:
+- compatible: Should be "linux,extcon-usb-gpio"
+
+Either one of id-gpio or vbus-gpio must be present. Both can be present as well.
+- id-gpio: gpio for USB ID pin. See gpio binding.
+- vbus-gpio: gpio for USB VBUS pin.
+
+Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below:
+	extcon_usb1 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
+	}
+
+	&omap_dwc3_1 {
+		extcon = <&extcon_usb1>;
+	};
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml
new file mode 100644
index 000000000..2e5b39881
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usbc-cros-ec.yaml
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-usbc-cros-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ChromeOS EC USB Type-C cable and accessories detection
+
+maintainers:
+  - Benson Leung <bleung@chromium.org>
+
+description: |
+  On ChromeOS systems with USB Type C ports, the ChromeOS Embedded Controller is
+  able to detect the state of external accessories such as display adapters
+  or USB devices when said accessories are attached or detached.
+  The node for this device must be under a cros-ec node like google,cros-ec-spi
+  or google,cros-ec-i2c.
+
+properties:
+  compatible:
+    const: google,extcon-usbc-cros-ec
+
+  google,usb-port-id:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: the port id
+    minimum: 0
+    maximum: 255
+
+required:
+  - compatible
+  - google,usb-port-id
+
+additionalProperties: false
+
+examples:
+  - |
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        cros-ec@0 {
+            compatible = "google,cros-ec-spi";
+            reg = <0>;
+            interrupts = <44 0>;
+
+            usbc_extcon0: extcon0 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <0>;
+            };
+
+            usbc_extcon1: extcon1 {
+                compatible = "google,extcon-usbc-cros-ec";
+                google,usb-port-id = <1>;
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/extcon-usbc-tusb320.yaml b/Documentation/devicetree/bindings/extcon/extcon-usbc-tusb320.yaml
new file mode 100644
index 000000000..71a9f2e5d
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/extcon-usbc-tusb320.yaml
@@ -0,0 +1,43 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/extcon-usbc-tusb320.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI TUSB320 USB Type-C CC Logic controller
+
+maintainers:
+  - Michael Auchter <michael.auchter@ni.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,tusb320
+      - ti,tusb320l
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        tusb320@61 {
+            compatible = "ti,tusb320";
+            reg = <0x61>;
+            interrupt-parent = <&gpio>;
+            interrupts = <27 1>;
+        };
+    };
+...
diff --git a/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml b/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml
new file mode 100644
index 000000000..ef6a246a1
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/fcs,fsa880.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/fcs,fsa880.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Fairchild Semiconductor FSA880, FSA9480 and compatibles
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+  The FSA880 and FSA9480 are USB port accessory detectors and switches.
+  The switch is fully controlled using I2C and enables USB data, stereo
+  and mono audio, video, microphone, and UART data to use a common
+  connector port. Compatible switches exist from other manufacturers.
+
+properties:
+  compatible:
+    enum:
+      - fcs,fsa880
+      - fcs,fsa9480
+      - ti,tsu6111
+
+  reg:
+    maxItems: 1
+    description: The I2C address for an FSA880 compatible device is
+      usually 0x25.
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        usb-switch@25 {
+            compatible = "fcs,fsa880";
+            reg = <0x25>;
+            interrupt-parent = <&gpio>;
+            interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/maxim,max77843.yaml b/Documentation/devicetree/bindings/extcon/maxim,max77843.yaml
new file mode 100644
index 000000000..128960545
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/maxim,max77843.yaml
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/maxim,max77843.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX77843 MicroUSB and Companion Power Management IC Extcon
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+  - Krzysztof Kozlowski <krzk@kernel.org>
+
+description: |
+  This is a part of device tree bindings for Maxim MAX77843 MicroUSB
+  Integrated Circuit (MUIC).
+
+  See also Documentation/devicetree/bindings/mfd/maxim,max77843.yaml for
+  additional information and example.
+
+properties:
+  compatible:
+    const: maxim,max77843-muic
+
+  connector:
+    $ref: /schemas/connector/usb-connector.yaml#
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    description:
+      Any connector to the data bus of this controller should be modelled using
+      the OF graph bindings specified
+    properties:
+      port:
+        $ref: /schemas/graph.yaml#/properties/port
+
+required:
+  - compatible
+  - connector
+
+additionalProperties: false
diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.yaml b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.yaml
new file mode 100644
index 000000000..6a9c96f03
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/qcom,pm8941-misc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Technologies, Inc. PM8941 USB ID Extcon device
+
+maintainers:
+  - Guru Das Srinagesh <gurus@codeaurora.org>
+
+description: |
+  Some Qualcomm PMICs have a "misc" module that can be used to detect when
+  the USB ID pin has been pulled low or high.
+
+properties:
+  compatible:
+    items:
+      - const: qcom,pm8941-misc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    minItems: 1
+    items:
+      - const: usb_id
+      - const: usb_vbus
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    pmic {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            interrupt-controller;
+            #interrupt-cells = <4>;
+
+            usb_id: misc@900 {
+                    compatible = "qcom,pm8941-misc";
+                    reg = <0x900>;
+                    interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
+                    interrupt-names = "usb_id";
+            };
+    };
+
+    usb-controller {
+           extcon = <&usb_id>;
+    };
diff --git a/Documentation/devicetree/bindings/extcon/siliconmitus,sm5502-muic.yaml b/Documentation/devicetree/bindings/extcon/siliconmitus,sm5502-muic.yaml
new file mode 100644
index 000000000..7a224b2f0
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/siliconmitus,sm5502-muic.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/siliconmitus,sm5502-muic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SM5502/SM5504 MUIC (Micro-USB Interface Controller) device
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+
+description:
+  The Silicon Mitus SM5502 is a MUIC (Micro-USB Interface Controller) device
+  which can detect the state of external accessory when external accessory is
+  attached or detached and button is pressed or released. It is interfaced to
+  the host controller using an I2C interface.
+
+properties:
+  compatible:
+    enum:
+      - siliconmitus,sm5502-muic
+      - siliconmitus,sm5504-muic
+      - siliconmitus,sm5703-muic
+
+  reg:
+    maxItems: 1
+    description: I2C slave address of the device. Usually 0x25 for SM5502
+      and SM5703, 0x14 for SM5504.
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        extcon@25 {
+                compatible = "siliconmitus,sm5502-muic";
+                reg = <0x25>;
+                interrupt-parent = <&msmgpio>;
+                interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml
new file mode 100644
index 000000000..efdf59abb
--- /dev/null
+++ b/Documentation/devicetree/bindings/extcon/wlf,arizona.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/extcon/wlf,arizona.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs
+
+maintainers:
+  - patches@opensource.cirrus.com
+
+description: |
+  These devices are audio SoCs with extensive digital capabilities and a
+  range of analogue I/O.
+
+  This document lists Extcon specific bindings, see the primary binding
+  document ../mfd/arizona.yaml
+
+properties:
+  wlf,hpdet-channel:
+    description:
+      Headphone detection channel.  ARIZONA_ACCDET_MODE_HPL/1 sets the
+      headphone detect mode to HPDETL, ARIZONA_ACCDET_MODE_HPR/2 sets it
+      to HPDETR.  If this node is not included or if the value is unknown,
+      then headphone detection mode is set to HPDETL.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 1
+    maximum: 2
+
+  wlf,use-jd2:
+    description:
+      Use the additional JD input along with JD1 for dual pin jack detection.
+    type: boolean
+
+  wlf,use-jd2-nopull:
+    description:
+      Internal pull on JD2 is disabled when used for jack detection.
+    type: boolean
+
+  wlf,jd-invert:
+    description:
+      Invert the polarity of the jack detection switch.
+    type: boolean
+
+  wlf,micd-software-compare:
+    description:
+      Use a software comparison to determine mic presence.
+    type: boolean
+
+  wlf,micd-detect-debounce:
+    description:
+      Additional software microphone detection debounce specified in
+      milliseconds.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+
+  wlf,micd-pol-gpio:
+    description:
+      GPIO specifier for the GPIO controlling the headset polarity if one
+      exists.
+    maxItems: 1
+
+  wlf,micd-bias-start-time:
+    description:
+      Time allowed for MICBIAS to startup prior to performing microphone
+      detection, specified as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-rate:
+    description:
+      Delay between successive microphone detection measurements, specified
+      as per the ARIZONA_MICD_TIME_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 12
+
+  wlf,micd-dbtime:
+    description:
+      Microphone detection hardware debounces specified as the number of
+      measurements to take.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    enum: [2, 4]
+
+  wlf,micd-timeout-ms:
+    description:
+      Timeout for microphone detection, specified in milliseconds.
+
+  wlf,micd-force-micbias:
+    description:
+      Force MICBIAS continuously on during microphone detection.
+    type: boolean
+
+  wlf,micd-configs:
+    description:
+      Headset polarity configurations (generally used for detection of
+      CTIA / OMTP headsets), the field can be of variable length but
+      should always be a multiple of 3 cells long, each three cell group
+      represents one polarity configuration.
+    $ref: "/schemas/types.yaml#/definitions/uint32-matrix"
+    items:
+      items:
+        - description:
+            The first cell defines the accessory detection pin, zero
+            will use MICDET1 and 0x2000 will use MICDET2.
+          enum: [ 0, 0x2000 ]
+        - description:
+            The second cell represents the MICBIAS to be used. Zero
+            will use MICVDD, 1-3 will use MICBIASx.
+          minimum: 0
+          maximum: 3
+        - description:
+            The third cell represents the value of the micd-pol-gpio
+            pin.
+          minimum: 0
+          maximum: 1
+
+  wlf,gpsw:
+    description:
+      Settings for the general purpose switch, set as one of the
+      ARIZONA_GPSW_XXX defines.
+    $ref: "/schemas/types.yaml#/definitions/uint32"
+    minimum: 0
+    maximum: 3
+
+additionalProperties: true